Coverage matrix¶
One row per datasheet (Rev. 7) parameter: register, bit field, interrupt source, state, electrical or
timing parameter, pin, OTP value. Each row names the driver API, the model behaviour and the test suite
with its files; the status says whether the behaviour is covered. The source is
coverage-matrix.csv; this page is generated from it by
python3 tools/coverage_matrix.py write, and python3 tools/coverage_matrix.py check verifies the totals
against Coverage.
Totals: 1090 rows; OK 729, INFO 360, TODO 1.
The test suite ids (T01 to T28) name groups of tests; the files column lists where they live. A suite
is not one test case: it is the set of cases in those files that exercise the behaviour.
| Suite | Test cases | Files |
|---|---|---|
| T01 | every I/O call returns NotInitialized before EnsureInitialized | tests/test_config.cpp; inc/pf1550_codec.hpp (static_assert) |
| T02 | EnsureInitialized reads DEVICE_ID and the charger, writes nothing; Config without Limits is rejected before any I/O; failures of the bus and of identity | |
| T03 | Limits are mandatory and must be sane; charger values are on the grid and inside Limits | tests/test_configure.cpp |
| T04 | every safety downgrade needs its acknowledgement; rails: windows, grids, DVS declaration, low power | tests/test_model.cpp; tests/test_configure.cpp |
| T05 | coin cell, power block and power-down order need their acknowledgements | |
| T06 | an enumerator that is not one is rejected; codecs: grids, anchors and reserved codes | |
| T07 | charger block writes the documented bytes and leaves the mode last; charger mode LinearOnly leaves charging off; reserved bits and fields the block does not own are preserved; JEITA, DPM, debounce and interrupt options reach their fields | tests/test_charger.cpp |
| T08 | the BATFET fault policy and DISBATFET are written when acknowledged | tests/test_charger.cpp |
| T09 | buck and LDO blocks: enables, voltages, current limit, forced PWM; the rail order is the caller's; a DVS step waits for the done flag, and an unchanged voltage does not; a DVS step that never finishes times out | tests/test_charger.cpp |
| T10 | coin cell, USB PHY, LED and power control reach their registers; reset paths and UVDET are written only when asked and acknowledged | tests/test_configure.cpp; tests/test_charger.cpp |
| T11 | Configure refuses charging while the charger reports a fault | tests/test_charger.cpp |
| T12 | a write that does not hold is reported; a bus error in the middle of Configure stops it | tests/test_irq.cpp |
| T13 | no write reaches a register that is not meant to be written | tests/test_power.cpp |
| T14 | the interrupt mask block writes defined bits and preserves reserved ones | tests/test_rails.cpp; tests/test_configure.cpp |
| T15 | charger states decode from CHG_SNS, including reserved codes; battery states, flags and the watchdog readings; VBUS flags decode | tests/test_irq.cpp; tests/test_rails.cpp |
| T16 | a charger state that changes between the two reads is flagged | tests/test_power.cpp; tests/test_rails.cpp; tests/test_review.cpp |
| T17 | charging is enabled only with limits-covered registers and no fault; charging with unsafe registers is refused whatever Configure did; SetChargerMode(Charge) checks the as-found values and reports them | tests/test_configure.cpp |
| T18 | RestartCharger cycles off and on, a bounded number of times | tests/test_power.cpp; tests/test_configure.cpp |
| T19 | the watchdog is serviced by WDTCLR = 1 and the other bits are kept; as found: option A1 starts the charger with no fast-charge timer; as found: MakeSafe writes CHG_OPER = linear only and verifies; as found: acknowledgements make an untimed charger acceptable; as found: limits below the OTP charge values give OutOfLimits; as found: a charger that is off is not checked; as found: each OTP option reads back its identity | tests/test_lifecycle.cpp; tests/test_model.cpp |
| T20 | ReadRail decodes each option's start-up values; load switch and low power flags read back | |
| T21 | SetRailVoltage: LDOs, DVS bucks and the refusals; a rail with no window is never driven | tests/test_lifecycle.cpp; tests/test_errors.cpp |
| T22 | variants: A0 and unlisted flavour bytes are reported, never an error; SILICON_REV and the address code are reported raw; power states decode and a reserved code is Unknown; SetRailModes writes the four enables and checks the low power rule | tests/test_irq.cpp |
| T23 | the load switch is one way and needs a window and a token | |
| T27 | the STANDBY pin goes through the port, or the call is Unsupported |
Registers¶
| Id | Item | Datasheet | API | Model | Test | Status |
|---|---|---|---|---|---|---|
| REG-00 | 0x00 DEVICE_ID [RO] | Table 86 p81 | EnsureInitialized(): reads 0x00, requires 0x7C else DeviceIdMismatch | fixed 0x7C | T19: tests/test_lifecycle.cpp; tests/test_model.cpp | OK |
| REG-01 | 0x01 OTP_FLAVOR [RO] | Table 87 p81 | ReadVariant(): raw byte + named option (A0 reading, A1..A9, else Unknown; C10) | per-option value | T19: tests/test_lifecycle.cpp; tests/test_model.cpp | OK |
| REG-02 | 0x02 SILICON_REV [RO] | Table 88 p81 | Snapshot.silicon_rev raw; no decision made on it | stored; knob silicon_rev_reset (C22) | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| REG-06 | 0x06 INT_CATEGORY [RO] | Table 89 p81 | ServiceInterrupts(): summary read first | derived OR of STAT bits | T12: tests/test_irq.cpp | OK |
| REG-08 | 0x08 SW_INT_STAT0 [STAT] | Table 90 p82 | ServiceInterrupts(): SW low-side current limit events returned; write-1 clear only of reported bits (C3) | set by event, cleared per knob int_clear | T12,T15: tests/test_irq.cpp; tests/test_rails.cpp | OK |
| REG-09 | 0x09 SW_INT_MASK0 [MASK] | Table 91 p82 | IrqMask: unmask only requested sources, rest stay masked; unused bits preserved | mask gates INTB only; STAT still sets | T12: tests/test_irq.cpp | OK |
| REG-0A | 0x0A SW_INT_SENSE0 [SENSE] | Table 92 p83 | Snapshot live sense; never cleared by driver | live state, not latched | T12,T22: tests/test_irq.cpp | OK |
| REG-0B | 0x0B SW_INT_STAT1 [STAT] | Table 93 p83 | ServiceInterrupts(): SW high-side current limit events returned; write-1 clear only of reported bits (C3) | set by event, cleared per knob int_clear | T12,T15: tests/test_irq.cpp; tests/test_rails.cpp | OK |
| REG-0C | 0x0C SW_INT_MASK1 [MASK] | Table 94 p84 | IrqMask: unmask only requested sources, rest stay masked; unused bits preserved | mask gates INTB only; STAT still sets | T12: tests/test_irq.cpp | OK |
| REG-0D | 0x0D SW_INT_SENSE1 [SENSE] | Table 95 p84 | Snapshot live sense; never cleared by driver | live state, not latched | T12,T22: tests/test_irq.cpp | OK |
| REG-0E | 0x0E SW_INT_STAT2 [STAT] | Table 96 p84 | ServiceInterrupts(): SW DVS done events returned; write-1 clear only of reported bits (C3) | set by event, cleared per knob int_clear | T12,T14: tests/test_irq.cpp; tests/test_rails.cpp; tests/test_configure.cpp | OK |
| REG-0F | 0x0F SW_INT_MASK2 [MASK] | Table 97 p85 | IrqMask: unmask only requested sources, rest stay masked; unused bits preserved | mask gates INTB only; STAT still sets | T12: tests/test_irq.cpp | OK |
| REG-10 | 0x10 SW_INT_SENSE2 [SENSE] | Table 98 p85 | Snapshot live sense; never cleared by driver | live state, not latched | T12,T22: tests/test_irq.cpp | OK |
| REG-18 | 0x18 LDO_INT_STAT0 [STAT] | Table 99 p85 | ServiceInterrupts(): LDO fault events returned; write-1 clear only of reported bits (C3) | set by event, cleared per knob int_clear | T12,T15: tests/test_irq.cpp; tests/test_rails.cpp | OK |
| REG-19 | 0x19 LDO_INT_MASK0 [MASK] | Table 100 p86 | IrqMask: unmask only requested sources, rest stay masked; unused bits preserved | mask gates INTB only; STAT still sets | T12: tests/test_irq.cpp | OK |
| REG-1A | 0x1A LDO_INT_SENSE0 [SENSE] | Table 101 p86 | Snapshot live sense; never cleared by driver | live state, not latched | T12,T22: tests/test_irq.cpp | OK |
| REG-20 | 0x20 TEMP_INT_STAT0 [STAT] | Table 102 p86 | ServiceInterrupts(): die temperature events returned; write-1 clear only of reported bits (C3) | set by event, cleared per knob int_clear | T12,T10: tests/test_irq.cpp; tests/test_configure.cpp; tests/test_charger.cpp | OK |
| REG-21 | 0x21 TEMP_INT_MASK0 [MASK] | Table 103 p87 | IrqMask: unmask only requested sources, rest stay masked; unused bits preserved | mask gates INTB only; STAT still sets | T12: tests/test_irq.cpp | OK |
| REG-22 | 0x22 TEMP_INT_SENSE0 [SENSE] | Table 104 p87 | Snapshot live sense; never cleared by driver | live state, not latched | T12,T22: tests/test_irq.cpp | OK |
| REG-24 | 0x24 ONKEY_INT_STAT0 [STAT] | Table 105 p87 | ServiceInterrupts(): ONKEY events returned; write-1 clear only of reported bits (C3) | set by event, cleared per knob int_clear | T12,T13: tests/test_irq.cpp; tests/test_power.cpp | OK |
| REG-25 | 0x25 ONKEY_INT_MASK0 [MASK] | Table 106 p88 | IrqMask: unmask only requested sources, rest stay masked; unused bits preserved | mask gates INTB only; STAT still sets | T12: tests/test_irq.cpp | OK |
| REG-26 | 0x26 ONKEY_INT_SENSE0 [SENSE] | Table 107 p89 | Snapshot live sense; never cleared by driver | live state, not latched | T12,T22: tests/test_irq.cpp | OK |
| REG-28 | 0x28 MISC_INT_STAT0 [STAT] | Table 108 p89 | ServiceInterrupts(): misc power events returned; write-1 clear only of reported bits (C3) | set by event, cleared per knob int_clear | T12,T13: tests/test_irq.cpp; tests/test_power.cpp | OK |
| REG-29 | 0x29 MISC_INT_MASK0 [MASK] | Table 109 p90 | IrqMask: unmask only requested sources, rest stay masked; unused bits preserved | mask gates INTB only; STAT still sets | T12: tests/test_irq.cpp | OK |
| REG-2A | 0x2A MISC_INT_SENSE0 [SENSE] | Table 110 p90 | Snapshot live sense; never cleared by driver | live state, not latched | T12,T22: tests/test_irq.cpp | OK |
| REG-30 | 0x30 COINCELL_CONTROL [GUARD] | Table 111 p91 | CoinCell{charge_enable, voltage_mv 1800..3300 step 100}; charge_enable needs ack coin_cell_is_rechargeable; codes above 0 need Limits.coin_cell_max_mv >= 3300 (C40) | VCOIN and COINCHEN stored; no knob (C40 open); LICELL charges to VCOIN while COINCHEN is set | T18,T05: tests/test_power.cpp; tests/test_configure.cpp; tests/test_config.cpp | OK |
| REG-32 | 0x32 SW1_VOLT [GUARD] | Table 112 p91 | SetRailVoltage(SW1): only when SW1 declared DVS (C1); microvolts grid 0.6 V+12.5 mV; inside Limits; STBY/SLP only on request; verify | DVS table or fixed table by option; write ignored when non-DVS (knob) | T01,T14,T05: tests/test_config.cpp; inc/pf1550_codec.hpp (static_assert); tests/test_rails.cpp; tests/test_configure.cpp | OK |
| REG-33 | 0x33 SW1_STBY_VOLT [GUARD] | Table 113 p91 | SetRailVoltage(SW1): only when SW1 declared DVS (C1); microvolts grid 0.6 V+12.5 mV; inside Limits; STBY/SLP only on request; verify | DVS table or fixed table by option; write ignored when non-DVS (knob) | T01,T14,T05: tests/test_config.cpp; inc/pf1550_codec.hpp (static_assert); tests/test_rails.cpp; tests/test_configure.cpp | OK |
| REG-34 | 0x34 SW1_SLP_VOLT [GUARD] | Table 114 p92 | SetRailVoltage(SW1): only when SW1 declared DVS (C1); microvolts grid 0.6 V+12.5 mV; inside Limits; STBY/SLP only on request; verify | DVS table or fixed table by option; write ignored when non-DVS (knob) | T01,T14,T05: tests/test_config.cpp; inc/pf1550_codec.hpp (static_assert); tests/test_rails.cpp; tests/test_configure.cpp | OK |
| REG-35 | 0x35 SW1_CTRL [CFG] | Table 115 p92 | BuckConfig(SW1).modes {run, standby, sleep, low_power}, dvs_speed, fpwm_in_dvs, fpwm, output_discharge | enable per mode (Table 30), DVS slew, discharge resistor | T14,T06: tests/test_rails.cpp; tests/test_configure.cpp | OK |
| REG-36 | 0x36 SW1_CTRL1 [CFG] | Table 116 p93 | BuckConfig.current_limit (ILIM 1.0/1.2/1.5/2.0 A typ); TMODE_SEL not exposed | ILIM stored; limit fault injected by test | T01,T15: tests/test_config.cpp; inc/pf1550_codec.hpp (static_assert); tests/test_irq.cpp; tests/test_rails.cpp | OK |
| REG-38 | 0x38 SW2_VOLT [GUARD] | Table 117 p93 | SetRailVoltage(SW2): only when SW2 declared DVS (C1); microvolts grid 0.6 V+12.5 mV; inside Limits; STBY/SLP only on request; verify | DVS table or fixed table by option; write ignored when non-DVS (knob) | T01,T14,T05: tests/test_config.cpp; inc/pf1550_codec.hpp (static_assert); tests/test_rails.cpp; tests/test_configure.cpp | OK |
| REG-39 | 0x39 SW2_STBY_VOLT [GUARD] | Table 118 p93 | SetRailVoltage(SW2): only when SW2 declared DVS (C1); microvolts grid 0.6 V+12.5 mV; inside Limits; STBY/SLP only on request; verify | DVS table or fixed table by option; write ignored when non-DVS (knob) | T01,T14,T05: tests/test_config.cpp; inc/pf1550_codec.hpp (static_assert); tests/test_rails.cpp; tests/test_configure.cpp | OK |
| REG-3A | 0x3A SW2_SLP_VOLT [GUARD] | Table 119 p93 | SetRailVoltage(SW2): only when SW2 declared DVS (C1); microvolts grid 0.6 V+12.5 mV; inside Limits; STBY/SLP only on request; verify | DVS table or fixed table by option; write ignored when non-DVS (knob) | T01,T14,T05: tests/test_config.cpp; inc/pf1550_codec.hpp (static_assert); tests/test_rails.cpp; tests/test_configure.cpp | OK |
| REG-3B | 0x3B SW2_CTRL [CFG] | Table 120 p94 | BuckConfig(SW2).modes {run, standby, sleep, low_power}, dvs_speed, fpwm_in_dvs, fpwm, output_discharge | enable per mode (Table 30), DVS slew, discharge resistor | T14,T06: tests/test_rails.cpp; tests/test_configure.cpp | OK |
| REG-3C | 0x3C SW2_CTRL1 [CFG] | Table 121 p94 | BuckConfig.current_limit (ILIM 1.0/1.2/1.5/2.0 A typ); TMODE_SEL not exposed | ILIM stored; limit fault injected by test | T01,T15: tests/test_config.cpp; inc/pf1550_codec.hpp (static_assert); tests/test_irq.cpp; tests/test_rails.cpp | OK |
| REG-3E | 0x3E SW3_VOLT [RO] | Table 122 p95 | ReadRail(Sw3): decode Table 37; never written (read-only, 6.3.3) | loaded from OTP; writes ignored (knob C2) | T01,T04,T14: tests/test_config.cpp; inc/pf1550_codec.hpp (static_assert); tests/test_model.cpp; tests/test_configure.cpp; tests/test_rails.cpp | OK |
| REG-3F | 0x3F SW3_STBY_VOLT [RO] | Table 123 p95 | ReadRail(Sw3): decode Table 37; never written (read-only, 6.3.3) | loaded from OTP; writes ignored (knob C2) | T01,T04,T14: tests/test_config.cpp; inc/pf1550_codec.hpp (static_assert); tests/test_model.cpp; tests/test_configure.cpp; tests/test_rails.cpp | OK |
| REG-40 | 0x40 SW3_SLP_VOLT [RO] | Table 124 p95 | ReadRail(Sw3): decode Table 37; never written (read-only, 6.3.3) | loaded from OTP; writes ignored (knob C2) | T01,T04,T14: tests/test_config.cpp; inc/pf1550_codec.hpp (static_assert); tests/test_model.cpp; tests/test_configure.cpp; tests/test_rails.cpp | OK |
| REG-41 | 0x41 SW3_CTRL [CFG] | Table 125 p95 | BuckConfig(SW3).modes {run, standby, sleep, low_power}, fpwm, output_discharge | enable per mode (Table 36), discharge resistor | T14,T06: tests/test_rails.cpp; tests/test_configure.cpp | OK |
| REG-42 | 0x42 SW3_CTRL1 [CFG] | Table 126 p96 | BuckConfig.current_limit SW3; TMODE_SEL not exposed | ILIM stored | T01,T15: tests/test_config.cpp; inc/pf1550_codec.hpp (static_assert); tests/test_irq.cpp; tests/test_rails.cpp | OK |
| REG-48 | 0x48 VSNVS_CTRL [CFG] | Table 127 p96 | VsnvsConfig.local_bandgap_disable (LIBGDIS); CLKPULSE/FORCEBOS/VSNVS_VOLT not exposed | stored | T18: tests/test_power.cpp; tests/test_configure.cpp | OK |
| REG-4A | 0x4A VREFDDR_CTRL [CFG] | Table 128 p96 | VrefDdrConfig.modes for VREFDDR (EN/STBY_EN/OMODE/LPWR) | enable per mode | T18: tests/test_power.cpp; tests/test_configure.cpp | OK |
| REG-4C | 0x4C LDO1_VOLT [GUARD] | Table 129 p97 | SetRailVoltage(LDO1): grid Table 41/43, inside Limits, verify | code table | T01,T14,T05: tests/test_config.cpp; inc/pf1550_codec.hpp (static_assert); tests/test_rails.cpp; tests/test_configure.cpp | OK |
| REG-4D | 0x4D LDO1_CTRL [CFG] | Table 130 p97 | LdoConfig.modes for LDO1: EN/STBY_EN/OMODE/LPWR; LS_EN via EnableLoadSwitch (guarded, one-way) | enable per mode (Table 42/44); LS one-way | T14,T16: tests/test_rails.cpp; tests/test_configure.cpp; tests/test_power.cpp; tests/test_review.cpp | OK |
| REG-4F | 0x4F LDO2_VOLT [GUARD] | Table 131 p97 | SetRailVoltage(LDO2): grid Table 41/43, inside Limits, verify | code table | T01,T14,T05: tests/test_config.cpp; inc/pf1550_codec.hpp (static_assert); tests/test_rails.cpp; tests/test_configure.cpp | OK |
| REG-50 | 0x50 LDO2_CTRL [CFG] | Table 132 p98 | LdoConfig.modes for LDO2: EN/STBY_EN/OMODE/LPWR; LS_EN via EnableLoadSwitch (guarded, one-way) | enable per mode (Table 42/44); LS one-way | T14,T16: tests/test_rails.cpp; tests/test_configure.cpp; tests/test_power.cpp; tests/test_review.cpp | OK |
| REG-52 | 0x52 LDO3_VOLT [GUARD] | Table 133 p98 | SetRailVoltage(LDO3): grid Table 41/43, inside Limits, verify | code table | T01,T14,T05: tests/test_config.cpp; inc/pf1550_codec.hpp (static_assert); tests/test_rails.cpp; tests/test_configure.cpp | OK |
| REG-53 | 0x53 LDO3_CTRL [CFG] | Table 134 p98 | LdoConfig.modes for LDO3: EN/STBY_EN/OMODE/LPWR; LS_EN via EnableLoadSwitch (guarded, one-way) | enable per mode (Table 42/44); LS one-way | T14,T16: tests/test_rails.cpp; tests/test_configure.cpp; tests/test_power.cpp; tests/test_review.cpp | OK |
| REG-58 | 0x58 PWRCTRL0 [GUARD] | Table 135 p99 | PowerConfig: STANDBYDLY, STANDBYINV typed; TGRESET guarded; POR_DLY not exposed (OTP, code 001 undefined C30) | stored; STANDBY pin logic (Table 76) | T13,T23: tests/test_power.cpp; tests/test_configure.cpp | OK |
| REG-59 | 0x59 PWRCTRL1 [GUARD] | Table 136 p99 | PowerConfig: debounces; PWRONRSTEN/RESTARTEN/ONKEY_RST_EN need ack hard_reset_paths; REGSCPEN typed | stored; ONKEY/PWRON events | T13,T23,T05: tests/test_power.cpp; tests/test_configure.cpp; tests/test_config.cpp | OK |
| REG-5A | 0x5A PWRCTRL2 [GUARD] | Table 137 p100 | PowerConfig.low_sys_warn typed; UVDET needs ack undervoltage_threshold | thresholds on injected VSYS | T13,T23: tests/test_power.cpp; tests/test_configure.cpp | OK |
| REG-5B | 0x5B PWRCTRL3 [GUARD] | Table 138 p100 | EnterShip(ShipConfirm), EnterCoreOff(CoreOffConfirm): preconditions in section 2.5 (C6, C7) | Table 83 G/I/J/K/L; no knob (C6: SHIP only without VBUS, the driver refuses the call with VBUS valid) | T16: tests/test_power.cpp; tests/test_rails.cpp; tests/test_review.cpp | OK |
| REG-5F | 0x5F SW1_PWRDN_SEQ [NOEXP] | Table 139 p101 | ReadPowerDownSequence(), SetPowerDownSequence() (needs power_down_order_reviewed), PowerDownDelayUs() | power-down order mirrors the power-up order after reset; the model runs the schedule | T03,T04: tests/test_configure.cpp; tests/test_model.cpp | OK |
| REG-60 | 0x60 SW2_PWRDN_SEQ [NOEXP] | Table 140 p101 | ReadPowerDownSequence(), SetPowerDownSequence() (needs power_down_order_reviewed), PowerDownDelayUs() | power-down order mirrors the power-up order after reset; the model runs the schedule | T03,T04: tests/test_configure.cpp; tests/test_model.cpp | OK |
| REG-61 | 0x61 SW3_PWRDN_SEQ [NOEXP] | Table 141 p102 | ReadPowerDownSequence(), SetPowerDownSequence() (needs power_down_order_reviewed), PowerDownDelayUs() | power-down order mirrors the power-up order after reset; the model runs the schedule | T03,T04: tests/test_configure.cpp; tests/test_model.cpp | OK |
| REG-62 | 0x62 LDO1_PWRDN_SEQ [NOEXP] | Table 142 p102 | ReadPowerDownSequence(), SetPowerDownSequence() (needs power_down_order_reviewed), PowerDownDelayUs() | power-down order mirrors the power-up order after reset; the model runs the schedule | T03,T04: tests/test_configure.cpp; tests/test_model.cpp | OK |
| REG-63 | 0x63 LDO2_PWRDN_SEQ [NOEXP] | Table 143 p103 | ReadPowerDownSequence(), SetPowerDownSequence() (needs power_down_order_reviewed), PowerDownDelayUs() | power-down order mirrors the power-up order after reset; the model runs the schedule | T03,T04: tests/test_configure.cpp; tests/test_model.cpp | OK |
| REG-64 | 0x64 LDO3_PWRDN_SEQ [NOEXP] | Table 144 p103 | ReadPowerDownSequence(), SetPowerDownSequence() (needs power_down_order_reviewed), PowerDownDelayUs() | power-down order mirrors the power-up order after reset; the model runs the schedule | T03,T04: tests/test_configure.cpp; tests/test_model.cpp | OK |
| REG-65 | 0x65 VREFDDR_PWRDN_SEQ [NOEXP] | Table 145 p104 | ReadPowerDownSequence(), SetPowerDownSequence() (needs power_down_order_reviewed), PowerDownDelayUs() | power-down order mirrors the power-up order after reset; the model runs the schedule | T03,T04: tests/test_configure.cpp; tests/test_model.cpp | OK |
| REG-67 | 0x67 STATE_INFO [RO] | Table 146 p104 | ReadPowerState(): STATE[5:0] decode, others Unknown | state machine output | T13: tests/test_power.cpp | OK |
| REG-68 | 0x68 I2C_ADDR [RO] | Table 147 p104 | EnsureInitialized(): address read-back; USE_DEFAULT_ADDR not touched | per option 0x08..0x0F | T19: tests/test_lifecycle.cpp; tests/test_model.cpp | OK |
| REG-69 | 0x69 IO_DRV0 [NOEXP] | Table 174 p125 | IO_DRV0: bitmap only, no field text; not exposed (undocumented) | stored (all RW) | T04: tests/test_model.cpp; tests/test_configure.cpp | INFO |
| REG-6A | 0x6A IO_DRV1 [NOEXP] | Table 174 p125 | IO_DRV1: bitmap only, no field text; not exposed (undocumented) | stored (b1:0 RW) | T04: tests/test_model.cpp; tests/test_configure.cpp | INFO |
| REG-6B | 0x6B RC_16MHZ [NOEXP] | Table 148 p105 | RC_16MHZ: forces clocks on (current cost only); not exposed | stored | T04: tests/test_model.cpp; tests/test_configure.cpp | INFO |
| REG-6F | 0x6F KEY1 [NOEXP] | Table 174 p125 | KEY1 (bitmap address; Table 149 prints 0x6B): not exposed; value sequence undocumented (C5) | stored | T04: tests/test_model.cpp; tests/test_configure.cpp | INFO |
| REG-80 | 0x80 CHG_INT [STAT] | Table 150 p105 | ServiceInterrupts(): charger events; clear per C3 (Table 150 RW1S vs bitmap RW1C) | set on state changes (Figure 16); clear per knob | T12,T07,T08: tests/test_irq.cpp; tests/test_charger.cpp | OK |
| REG-82 | 0x82 CHG_INT_MASK [MASK] | Table 151 p106 | IrqMask for charger sources | mask gates INTB | T12: tests/test_irq.cpp | OK |
| REG-84 | 0x84 CHG_INT_OK [RO] | Table 152 p107 | ReadChargerStatus(): OK flags | derived from state machine | T07,T22: tests/test_charger.cpp; tests/test_irq.cpp | OK |
| REG-86 | 0x86 VBUS_SNS [RO] | Table 153 p107 | ReadChargerStatus(): VBUS flags | derived from VBUS voltage model | T11,T22: tests/test_charger.cpp; tests/test_irq.cpp | OK |
| REG-87 | 0x87 CHG_SNS [RO] | Table 154 p108 | ReadChargerStatus(): state + WDT/THM/TREG; reserved -> Unknown fault | charger state machine | T07,T08,T22: tests/test_charger.cpp; tests/test_irq.cpp | OK |
| REG-88 | 0x88 BATT_SNS [RO] | Table 155 p109 | ReadChargerStatus(): battery state + BATTOC | battery model | T08,T22: tests/test_charger.cpp; tests/test_irq.cpp | OK |
| REG-89 | 0x89 CHG_OPER [GUARD] | Table 156 p109 | ChargerConfig.mode (Off/LinearOnly/Charge) written last; DISBATFET needs ack; WDTEN via Watchdog | mode per Table 156 | T06,T07,T05: tests/test_configure.cpp; tests/test_charger.cpp; tests/test_config.cpp | OK |
| REG-8A | 0x8A CHG_TMR [GUARD] | Table 157 p110 | ChargerConfig timers; fast timer disabled only with ack allow_untimed_charge | timers on scaled clock | T09,T05: tests/test_charger.cpp; tests/test_config.cpp | OK |
| REG-8D | 0x8D CHG_EOC_CNFG [GUARD] | Table 158 p111 | ChargerConfig.termination_ma, restart; IEOC 5 or 10 mA needs ack eoc_accuracy_accepted (T10 IEOC accuracy) | EOC detection, restart | T07,T05: tests/test_charger.cpp; tests/test_config.cpp | OK |
| REG-8E | 0x8E CHG_CURR_CNFG [GUARD] | Table 159 p112 | ChargerConfig.charge_current_ma <= Limits.cell_max_charge_ma; reserved codes unencodable | IFC applied; foldback | T01,T02,T05,T07: tests/test_config.cpp; inc/pf1550_codec.hpp (static_assert); tests/test_review.cpp; tests/test_charger.cpp | OK |
| REG-8F | 0x8F BATT_REG [GUARD] | Table 160 p113 | ChargerConfig.charge_voltage_mv <= Limits.cell_max_mv; VSYSMIN typed | CV applied (AppliedCvMv) | T01,T02,T05,T07: tests/test_config.cpp; inc/pf1550_codec.hpp (static_assert); tests/test_review.cpp; tests/test_charger.cpp | OK |
| REG-91 | 0x91 BATFET_CNFG [GUARD] | Table 161 p114 | ChargerConfig.batfet.{oc_threshold, oc_keeps_closed, oc_without_vbus}, watchdog.time; ServiceChargerWatchdog() writes WDTCLR | BATFET overcurrent, watchdog | T08,T09,T05: tests/test_charger.cpp; tests/test_config.cpp | OK |
| REG-92 | 0x92 THM_REG_CNFG [GUARD] | Table 162 p115 | ChargerConfig.thermistor, thermal_reg.{temperature, foldback}, jeita.{cold, hot} | thermal/thermistor model | T10,T05: tests/test_configure.cpp; tests/test_charger.cpp; tests/test_config.cpp | OK |
| REG-94 | 0x94 VBUS_INLIM_CNFG [GUARD] | Table 163 p116 | ChargerConfig.input_limit_ma (21 codes) <= Limits.input_max_ma | input limit applied | T01,T02,T11,T05: tests/test_config.cpp; inc/pf1550_codec.hpp (static_assert); tests/test_review.cpp; tests/test_charger.cpp | OK |
| REG-95 | 0x95 VBUS_LIN_DPM [CFG] | Table 164 p117 | ChargerConfig.vbus.{dpm, dpm_stop}; PRECHGDBATT_THRSH and FET_SCALE not exposed | DPM loop | T01,T11: tests/test_config.cpp; inc/pf1550_codec.hpp (static_assert); tests/test_charger.cpp | OK |
| REG-96 | 0x96 USB_PHY_LDO_CNFG [CFG] | Table 165 p117 | UsbPhyConfig{enable, voltage 3.¾.9 V, active_discharge} | model output UsbphyEnabled()/UsbphyMv() (state only, analog not simulated) | T18: tests/test_power.cpp; tests/test_configure.cpp | OK |
| REG-98 | 0x98 DBNC_DELAY_TIME [CFG] | Table 166 p118 | ChargerConfig.vbus.{ovlo_debounce, sys_wakeup_delay}; USB_PHY_TDB not exposed | delays in the VBUS comparator | T11,T20: tests/test_charger.cpp; tests/test_configure.cpp | OK |
| REG-99 | 0x99 CHG_INT_CNFG [CFG] | Table 167 p118 | ChargerConfig.interrupts.{every_transition, eoc} | interrupt generation per bits | T12: tests/test_irq.cpp | OK |
| REG-9A | 0x9A THM_ADJ_SETTING [GUARD] | Table 168 p118 | ChargerConfig.jeita.{warm, cool, cv_adjust, cc_adjust} | JEITA model | T10: tests/test_configure.cpp; tests/test_charger.cpp | OK |
| REG-9B | 0x9B VBUS2SYS_CNFG [CFG] | Table 169 p119 | ChargerConfig.vbus.{vbus2sys_threshold, vbus2sys_debounce} | VBUS_VALID comparator | T11: tests/test_charger.cpp | OK |
| REG-9C | 0x9C LED_PWM [CFG] | Table 170 p120 | LedConfig.{enable, duty_32nds 0..32, ramp} | model output Led() per Tables 70, 71 | T17: tests/test_configure.cpp | OK |
| REG-9D | 0x9D FAULT_BATFET_CNFG [GUARD] | Table 171 p120 | ChargerConfig.batfet.fault_policy.{on_overvoltage, on_watchdog, on_thermistor, on_thermal_shutdown, on_timer_fault}; keep-closed needs ack allow_batfet_closed_on_fault | BATFET policy per fault | T08,T05: tests/test_charger.cpp; tests/test_config.cpp | OK |
| REG-9E | 0x9E LED_CNFG [CFG] | Table 172 p121 | LedConfig.{frequency, mode, software_override}; LED_CURRENT written 01 (6 mA) when the LED is used | model output Led() and blink period | T17: tests/test_configure.cpp | OK |
| REG-9F | 0x9F CHGR_KEY2 [NOEXP] | Table 173 p122 | CHGR_KEY2: Reserved; not exposed (C5) | stored | T04: tests/test_model.cpp; tests/test_configure.cpp | INFO |
Bit fields¶
| Id | Item | Datasheet | API | Model | Test | Status |
|---|---|---|---|---|---|---|
| FLD-00.DEVICE_ID | 0x00 DEVICE_ID[2:0] DEVICE_ID (R, reset 100) | Table 86 p81 | EnsureInitialized(): low 3 bits must read 100 | fixed | T19: tests/test_lifecycle.cpp; tests/test_model.cpp | OK |
| FLD-00.FAMILY | 0x00 DEVICE_ID[7:3] FAMILY (R, reset 01111) | Table 86 p81 | EnsureInitialized(): bits 7:3 must read 01111 | fixed | T19: tests/test_lifecycle.cpp; tests/test_model.cpp | OK |
| FLD-01.UNUSED | 0x01 OTP_FLAVOR[7:0] UNUSED (R, reset 0x00) | Table 87 p81 | VariantInfo.flavor_raw and .option (named for listed values, Unknown otherwise, C10) | per-option value | T19: tests/test_lifecycle.cpp; tests/test_model.cpp | OK |
| FLD-02.METAL_LAYER_REV | 0x02 SILICON_REV[2:0] METAL_LAYER_REV (R, reset 001) | Table 88 p81 | VariantInfo.silicon_rev_raw (whole byte, no decision made on it, C22) | knob silicon_rev_reset | T19: tests/test_lifecycle.cpp; tests/test_model.cpp | OK |
| FLD-02.FULL_LAYER_REV | 0x02 SILICON_REV[5:3] FULL_LAYER_REV (R, reset 010) | Table 88 p81 | VariantInfo.silicon_rev_raw (whole byte, no decision made on it, C22) | knob silicon_rev_reset | T19: tests/test_lifecycle.cpp; tests/test_model.cpp | OK |
| FLD-02.FAB_FIN | 0x02 SILICON_REV[7:6] FAB_FIN (R, reset 00) | Table 88 p81 | VariantInfo.silicon_rev_raw (whole byte, no decision made on it, C22) | knob silicon_rev_reset | T19: tests/test_lifecycle.cpp; tests/test_model.cpp | OK |
| FLD-06.CHG_INT | 0x06 INT_CATEGORY[0] CHG_INT (R, reset 0) | Table 89 p81 | ServiceInterrupts(): summary read first; InterruptEvents.categories.chg | derived OR of the group status bits (C28) | T12: tests/test_irq.cpp | OK |
| FLD-06.SW1_INT | 0x06 INT_CATEGORY[1] SW1_INT (R, reset 0) | Table 89 p81 | ServiceInterrupts(): summary read first; InterruptEvents.categories.sw1 | derived OR of the group status bits (C28) | T12: tests/test_irq.cpp | OK |
| FLD-06.SW2_INT | 0x06 INT_CATEGORY[2] SW2_INT (R, reset 0) | Table 89 p81 | ServiceInterrupts(): summary read first; InterruptEvents.categories.sw2 | derived OR of the group status bits (C28) | T12: tests/test_irq.cpp | OK |
| FLD-06.SW3_INT | 0x06 INT_CATEGORY[3] SW3_INT (R, reset 0) | Table 89 p81 | ServiceInterrupts(): summary read first; InterruptEvents.categories.sw3 | derived OR of the group status bits (C28) | T12: tests/test_irq.cpp | OK |
| FLD-06.LDO_INT | 0x06 INT_CATEGORY[4] LDO_INT (R, reset 0) | Table 89 p81 | ServiceInterrupts(): summary read first; InterruptEvents.categories.ldo | derived OR of the group status bits (C28) | T12: tests/test_irq.cpp | OK |
| FLD-06.ONKEY_INT | 0x06 INT_CATEGORY[5] ONKEY_INT (R, reset 0) | Table 89 p81 | ServiceInterrupts(): summary read first; InterruptEvents.categories.onkey | derived OR of the group status bits (C28) | T12: tests/test_irq.cpp | OK |
| FLD-06.TEMP_INT | 0x06 INT_CATEGORY[6] TEMP_INT (R, reset 0) | Table 89 p81 | ServiceInterrupts(): summary read first; InterruptEvents.categories.temp | derived OR of the group status bits (C28) | T12: tests/test_irq.cpp | OK |
| FLD-06.MISC_INT | 0x06 INT_CATEGORY[7] MISC_INT (R, reset 0) | Table 89 p81 | ServiceInterrupts(): summary read first; InterruptEvents.categories.misc | derived OR of the group status bits (C28) | T12: tests/test_irq.cpp | OK |
| FLD-08.SW1_LS_I | 0x08 SW_INT_STAT0[0] SW1_LS_I (RW1C, reset 0) | Table 90 p82 | Has(events, IrqSource::Sw1LowSideLimit): returned by ServiceInterrupts(); cleared by write 1 of the reported bit only | status latch set by event, cleared per knob int_clear (C3) | T12,T15: tests/test_irq.cpp; tests/test_rails.cpp | OK |
| FLD-08.SW2_LS_I | 0x08 SW_INT_STAT0[1] SW2_LS_I (RW1C, reset 0) | Table 90 p82 | Has(events, IrqSource::Sw2LowSideLimit): returned by ServiceInterrupts(); cleared by write 1 of the reported bit only | status latch set by event, cleared per knob int_clear (C3) | T12,T15: tests/test_irq.cpp; tests/test_rails.cpp | OK |
| FLD-08.SW3_LS_I | 0x08 SW_INT_STAT0[2] SW3_LS_I (RW1C, reset 0) | Table 90 p82 | Has(events, IrqSource::Sw3LowSideLimit): returned by ServiceInterrupts(); cleared by write 1 of the reported bit only | status latch set by event, cleared per knob int_clear (C3) | T12,T15: tests/test_irq.cpp; tests/test_rails.cpp | OK |
| FLD-08.UNUSED | 0x08 SW_INT_STAT0[7:3] UNUSED (—, reset —) | Table 90 p82 | not exposed: reserved/unused; kept by read-modify-write, never forced | register file stores the bit | T03: tests/test_configure.cpp | INFO |
| FLD-09.SW1_LS_M | 0x09 SW_INT_MASK0[0] SW1_LS_M (RW, reset 1) | Table 91 p82 | UnmaskOnly({IrqSource::Sw1LowSideLimit}) (1 = masked, reset 1); driver unmasks only requested sources | mask gates INTB only; status still sets | T12: tests/test_irq.cpp | OK |
| FLD-09.SW2_LS_M | 0x09 SW_INT_MASK0[1] SW2_LS_M (RW, reset 1) | Table 91 p82 | UnmaskOnly({IrqSource::Sw2LowSideLimit}) (1 = masked, reset 1); driver unmasks only requested sources | mask gates INTB only; status still sets | T12: tests/test_irq.cpp | OK |
| FLD-09.SW3_LS_M | 0x09 SW_INT_MASK0[2] SW3_LS_M (RW, reset 1) | Table 91 p82 | UnmaskOnly({IrqSource::Sw3LowSideLimit}) (1 = masked, reset 1); driver unmasks only requested sources | mask gates INTB only; status still sets | T12: tests/test_irq.cpp | OK |
| FLD-09.UNUSED | 0x09 SW_INT_MASK0[7:3] UNUSED (—, reset —) | Table 91 p82 | not exposed: reserved/unused; kept by read-modify-write, never forced | register file stores the bit | T03: tests/test_configure.cpp | INFO |
| FLD-0A.SW1_LS_S | 0x0A SW_INT_SENSE0[0] SW1_LS_S (R, reset 0) | Table 92 p83 | Snapshot.sense[group] bit SW1_LS (ReadSense()): read only, not latched | live level | T12,T22: tests/test_irq.cpp | OK |
| FLD-0A.SW2_LS_S | 0x0A SW_INT_SENSE0[1] SW2_LS_S (R, reset 0) | Table 92 p83 | Snapshot.sense[group] bit SW2_LS (ReadSense()): read only, not latched | live level | T12,T22: tests/test_irq.cpp | OK |
| FLD-0A.SW3_LS_S | 0x0A SW_INT_SENSE0[2] SW3_LS_S (R, reset 0) | Table 92 p83 | Snapshot.sense[group] bit SW3_LS (ReadSense()): read only, not latched | live level | T12,T22: tests/test_irq.cpp | OK |
| FLD-0A.UNUSED | 0x0A SW_INT_SENSE0[7:3] UNUSED (—, reset —) | Table 92 p83 | not exposed: reserved/unused; kept by read-modify-write, never forced | register file stores the bit | T03: tests/test_configure.cpp | INFO |
| FLD-0B.SW1_HS_I | 0x0B SW_INT_STAT1[0] SW1_HS_I (RW1C, reset 0) | Table 93 p83 | Has(events, IrqSource::Sw1HighSideLimit): returned by ServiceInterrupts(); cleared by write 1 of the reported bit only | status latch set by event, cleared per knob int_clear (C3) | T12,T15: tests/test_irq.cpp; tests/test_rails.cpp | OK |
| FLD-0B.SW2_HS_I | 0x0B SW_INT_STAT1[1] SW2_HS_I (RW1C, reset 0) | Table 93 p83 | Has(events, IrqSource::Sw2HighSideLimit): returned by ServiceInterrupts(); cleared by write 1 of the reported bit only | status latch set by event, cleared per knob int_clear (C3) | T12,T15: tests/test_irq.cpp; tests/test_rails.cpp | OK |
| FLD-0B.SW3_HS_I | 0x0B SW_INT_STAT1[2] SW3_HS_I (RW1C, reset 0) | Table 93 p83 | Has(events, IrqSource::Sw3HighSideLimit): returned by ServiceInterrupts(); cleared by write 1 of the reported bit only | status latch set by event, cleared per knob int_clear (C3) | T12,T15: tests/test_irq.cpp; tests/test_rails.cpp | OK |
| FLD-0B.UNUSED | 0x0B SW_INT_STAT1[7:3] UNUSED (—, reset —) | Table 93 p83 | not exposed: reserved/unused; kept by read-modify-write, never forced | register file stores the bit | T03: tests/test_configure.cpp | INFO |
| FLD-0C.SW1_HS_M | 0x0C SW_INT_MASK1[0] SW1_HS_M (RW, reset 1) | Table 94 p84 | UnmaskOnly({IrqSource::Sw1HighSideLimit}) (1 = masked, reset 1); driver unmasks only requested sources | mask gates INTB only; status still sets | T12: tests/test_irq.cpp | OK |
| FLD-0C.SW2_HS_M | 0x0C SW_INT_MASK1[1] SW2_HS_M (RW, reset 1) | Table 94 p84 | UnmaskOnly({IrqSource::Sw2HighSideLimit}) (1 = masked, reset 1); driver unmasks only requested sources | mask gates INTB only; status still sets | T12: tests/test_irq.cpp | OK |
| FLD-0C.SW3_HS_M | 0x0C SW_INT_MASK1[2] SW3_HS_M (RW, reset 1) | Table 94 p84 | UnmaskOnly({IrqSource::Sw3HighSideLimit}) (1 = masked, reset 1); driver unmasks only requested sources | mask gates INTB only; status still sets | T12: tests/test_irq.cpp | OK |
| FLD-0C.UNUSED | 0x0C SW_INT_MASK1[7:3] UNUSED (—, reset —) | Table 94 p84 | not exposed: reserved/unused; kept by read-modify-write, never forced | register file stores the bit | T03: tests/test_configure.cpp | INFO |
| FLD-0D.SW1_HS_S | 0x0D SW_INT_SENSE1[0] SW1_HS_S (R, reset 0) | Table 95 p84 | Snapshot.sense[group] bit SW1_HS (ReadSense()): read only, not latched | live level | T12,T22: tests/test_irq.cpp | OK |
| FLD-0D.SW2_HS_S | 0x0D SW_INT_SENSE1[1] SW2_HS_S (R, reset 0) | Table 95 p84 | Snapshot.sense[group] bit SW2_HS (ReadSense()): read only, not latched | live level | T12,T22: tests/test_irq.cpp | OK |
| FLD-0D.SW3_HS_S | 0x0D SW_INT_SENSE1[2] SW3_HS_S (R, reset 0) | Table 95 p84 | Snapshot.sense[group] bit SW3_HS (ReadSense()): read only, not latched | live level | T12,T22: tests/test_irq.cpp | OK |
| FLD-0D.UNUSED | 0x0D SW_INT_SENSE1[7:3] UNUSED (—, reset —) | Table 95 p84 | not exposed: reserved/unused; kept by read-modify-write, never forced | register file stores the bit | T03: tests/test_configure.cpp | INFO |
| FLD-0E.SW1_DVS_DONE_I | 0x0E SW_INT_STAT2[0] SW1_DVS_DONE_I (RW1C, reset 0) | Table 96 p84 | Has(events, IrqSource::Sw1DvsDone): returned by ServiceInterrupts(); cleared by write 1 of the reported bit only | status latch set by event, cleared per knob int_clear (C3) | T12,T14: tests/test_irq.cpp; tests/test_rails.cpp; tests/test_configure.cpp | OK |
| FLD-0E.SW2_DVS_DONE_I | 0x0E SW_INT_STAT2[1] SW2_DVS_DONE_I (RW1C, reset 0) | Table 96 p84 | Has(events, IrqSource::Sw2DvsDone): returned by ServiceInterrupts(); cleared by write 1 of the reported bit only | status latch set by event, cleared per knob int_clear (C3) | T12,T14: tests/test_irq.cpp; tests/test_rails.cpp; tests/test_configure.cpp | OK |
| FLD-0E.UNUSED | 0x0E SW_INT_STAT2[7:2] UNUSED (—, reset —) | Table 96 p84 | not exposed: reserved/unused; kept by read-modify-write, never forced | register file stores the bit | T03: tests/test_configure.cpp | INFO |
| FLD-0F.SW1_DVS_DONE_M | 0x0F SW_INT_MASK2[0] SW1_DVS_DONE_M (RW, reset 1) | Table 97 p85 | UnmaskOnly({IrqSource::Sw1DvsDone}) (1 = masked, reset 1); driver unmasks only requested sources | mask gates INTB only; status still sets | T12: tests/test_irq.cpp | OK |
| FLD-0F.SW2_DVS_DONE_M | 0x0F SW_INT_MASK2[1] SW2_DVS_DONE_M (RW, reset 1) | Table 97 p85 | UnmaskOnly({IrqSource::Sw2DvsDone}) (1 = masked, reset 1); driver unmasks only requested sources | mask gates INTB only; status still sets | T12: tests/test_irq.cpp | OK |
| FLD-0F.UNUSED | 0x0F SW_INT_MASK2[7:2] UNUSED (—, reset —) | Table 97 p85 | not exposed: reserved/unused; kept by read-modify-write, never forced | register file stores the bit | T03: tests/test_configure.cpp | INFO |
| FLD-10.SW1_DVS_S | 0x10 SW_INT_SENSE2[0] SW1_DVS_S (R, reset 0) | Table 98 p85 | Snapshot.sense[group] bit SW1_DVS (ReadSense()): read only, not latched | live level | T12,T22: tests/test_irq.cpp | OK |
| FLD-10.SW2_DVS_S | 0x10 SW_INT_SENSE2[1] SW2_DVS_S (R, reset 0) | Table 98 p85 | Snapshot.sense[group] bit SW2_DVS (ReadSense()): read only, not latched | live level | T12,T22: tests/test_irq.cpp | OK |
| FLD-10.UNUSED | 0x10 SW_INT_SENSE2[7:2] UNUSED (—, reset —) | Table 98 p85 | not exposed: reserved/unused; kept by read-modify-write, never forced | register file stores the bit | T03: tests/test_configure.cpp | INFO |
| FLD-18.LDO1_FAULTI | 0x18 LDO_INT_STAT0[0] LDO1_FAULTI (RW1C, reset 0) | Table 99 p85 | Has(events, IrqSource::Ldo1Fault): returned by ServiceInterrupts(); cleared by write 1 of the reported bit only | status latch set by event, cleared per knob int_clear (C3) | T12,T15: tests/test_irq.cpp; tests/test_rails.cpp | OK |
| FLD-18.LDO2_FAULTI | 0x18 LDO_INT_STAT0[1] LDO2_FAULTI (RW1C, reset 0) | Table 99 p85 | Has(events, IrqSource::Ldo2Fault): returned by ServiceInterrupts(); cleared by write 1 of the reported bit only | status latch set by event, cleared per knob int_clear (C3) | T12,T15: tests/test_irq.cpp; tests/test_rails.cpp | OK |
| FLD-18.LDO3_FAULTI | 0x18 LDO_INT_STAT0[2] LDO3_FAULTI (RW1C, reset 0) | Table 99 p85 | Has(events, IrqSource::Ldo3Fault): returned by ServiceInterrupts(); cleared by write 1 of the reported bit only | status latch set by event, cleared per knob int_clear (C3) | T12,T15: tests/test_irq.cpp; tests/test_rails.cpp | OK |
| FLD-18.UNUSED | 0x18 LDO_INT_STAT0[7:3] UNUSED (—, reset —) | Table 99 p85 | not exposed: reserved/unused; kept by read-modify-write, never forced | register file stores the bit | T03: tests/test_configure.cpp | INFO |
| FLD-19.LDO1_FAULTM | 0x19 LDO_INT_MASK0[0] LDO1_FAULTM (RW, reset 1) | Table 100 p86 | UnmaskOnly({IrqSource::Ldo1Fault}) (1 = masked, reset 1); driver unmasks only requested sources | mask gates INTB only; status still sets | T12: tests/test_irq.cpp | OK |
| FLD-19.LDO2_FAULTM | 0x19 LDO_INT_MASK0[1] LDO2_FAULTM (RW, reset 1) | Table 100 p86 | UnmaskOnly({IrqSource::Ldo2Fault}) (1 = masked, reset 1); driver unmasks only requested sources | mask gates INTB only; status still sets | T12: tests/test_irq.cpp | OK |
| FLD-19.LDO3_FAULTM | 0x19 LDO_INT_MASK0[2] LDO3_FAULTM (RW, reset 1) | Table 100 p86 | UnmaskOnly({IrqSource::Ldo3Fault}) (1 = masked, reset 1); driver unmasks only requested sources | mask gates INTB only; status still sets | T12: tests/test_irq.cpp | OK |
| FLD-19.UNUSED | 0x19 LDO_INT_MASK0[7:3] UNUSED (—, reset —) | Table 100 p86 | not exposed: reserved/unused; kept by read-modify-write, never forced | register file stores the bit | T03: tests/test_configure.cpp | INFO |
| FLD-1A.LDO1_FAULTS | 0x1A LDO_INT_SENSE0[0] LDO1_FAULTS (R, reset 0) | Table 101 p86 | Snapshot.sense[group] bit LDO1 (ReadSense()): read only, not latched | live level | T12,T22: tests/test_irq.cpp | OK |
| FLD-1A.LDO2_FAULTS | 0x1A LDO_INT_SENSE0[1] LDO2_FAULTS (R, reset 0) | Table 101 p86 | Snapshot.sense[group] bit LDO2 (ReadSense()): read only, not latched | live level | T12,T22: tests/test_irq.cpp | OK |
| FLD-1A.LDO3_FAULTS | 0x1A LDO_INT_SENSE0[2] LDO3_FAULTS (R, reset 0) | Table 101 p86 | Snapshot.sense[group] bit LDO3 (ReadSense()): read only, not latched | live level | T12,T22: tests/test_irq.cpp | OK |
| FLD-1A.UNUSED | 0x1A LDO_INT_SENSE0[7:3] UNUSED (—, reset —) | Table 101 p86 | not exposed: reserved/unused; kept by read-modify-write, never forced | register file stores the bit | T03: tests/test_configure.cpp | INFO |
| FLD-20.THERM110I | 0x20 TEMP_INT_STAT0[0] THERM110I (RW1C, reset 0) | Table 102 p86 | Has(events, IrqSource::Temp110): returned by ServiceInterrupts(); cleared by write 1 of the reported bit only | status latch set by event, cleared per knob int_clear (C3) | T12,T10: tests/test_irq.cpp; tests/test_configure.cpp; tests/test_charger.cpp | OK |
| FLD-20.UNUSED | 0x20 TEMP_INT_STAT0[1] UNUSED (—, reset —) | Table 102 p86 | not exposed: reserved/unused; kept by read-modify-write, never forced | register file stores the bit | T03: tests/test_configure.cpp | INFO |
| FLD-20.THERM125I | 0x20 TEMP_INT_STAT0[2] THERM125I (RW1C, reset 0) | Table 102 p86 | Has(events, IrqSource::Temp125): returned by ServiceInterrupts(); cleared by write 1 of the reported bit only | status latch set by event, cleared per knob int_clear (C3) | T12,T10: tests/test_irq.cpp; tests/test_configure.cpp; tests/test_charger.cpp | OK |
| FLD-20.UNUSED[7:3] | 0x20 TEMP_INT_STAT0[7:3] UNUSED (—, reset —) | Table 102 p86 | not exposed: reserved/unused; kept by read-modify-write, never forced | register file stores the bit | T03: tests/test_configure.cpp | INFO |
| FLD-21.THERM110M | 0x21 TEMP_INT_MASK0[0] THERM110M (RW, reset 1) | Table 103 p87 | UnmaskOnly({IrqSource::Temp110}) (1 = masked, reset 1); driver unmasks only requested sources | mask gates INTB only; status still sets | T12: tests/test_irq.cpp | OK |
| FLD-21.UNUSED | 0x21 TEMP_INT_MASK0[1] UNUSED (—, reset —) | Table 103 p87 | not exposed: reserved/unused; kept by read-modify-write, never forced | register file stores the bit | T03: tests/test_configure.cpp | INFO |
| FLD-21.THERM125M | 0x21 TEMP_INT_MASK0[2] THERM125M (RW, reset 1) | Table 103 p87 | UnmaskOnly({IrqSource::Temp125}) (1 = masked, reset 1); driver unmasks only requested sources | mask gates INTB only; status still sets | T12: tests/test_irq.cpp | OK |
| FLD-21.UNUSED[7:3] | 0x21 TEMP_INT_MASK0[7:3] UNUSED (—, reset —) | Table 103 p87 | not exposed: reserved/unused; kept by read-modify-write, never forced | register file stores the bit | T03: tests/test_configure.cpp | INFO |
| FLD-22.THERM110S | 0x22 TEMP_INT_SENSE0[0] THERM110S (R, reset 0) | Table 104 p87 | Snapshot.sense[group] bit THERM110S (ReadSense()): read only, not latched | live level | T12,T22: tests/test_irq.cpp | OK |
| FLD-22.UNUSED | 0x22 TEMP_INT_SENSE0[1] UNUSED (—, reset —) | Table 104 p87 | not exposed: reserved/unused; kept by read-modify-write, never forced | register file stores the bit | T03: tests/test_configure.cpp | INFO |
| FLD-22.THERM125S | 0x22 TEMP_INT_SENSE0[2] THERM125S (R, reset 0) | Table 104 p87 | Snapshot.sense[group] bit THERM125S (ReadSense()): read only, not latched | live level | T12,T22: tests/test_irq.cpp | OK |
| FLD-22.UNUSED[7:3] | 0x22 TEMP_INT_SENSE0[7:3] UNUSED (—, reset —) | Table 104 p87 | not exposed: reserved/unused; kept by read-modify-write, never forced | register file stores the bit | T03: tests/test_configure.cpp | INFO |
| FLD-24.ONKEY_PUSHI | 0x24 ONKEY_INT_STAT0[0] ONKEY_PUSHI (RW1C, reset 0) | Table 105 p87 | Has(events, IrqSource::OnkeyPush): returned by ServiceInterrupts(); cleared by write 1 of the reported bit only | status latch set by event, cleared per knob int_clear (C3) | T12,T13: tests/test_irq.cpp; tests/test_power.cpp | OK |
| FLD-24.ONKEY_1SI | 0x24 ONKEY_INT_STAT0[1] ONKEY_1SI (RW1C, reset 0) | Table 105 p87 | Has(events, IrqSource::Onkey1s): returned by ServiceInterrupts(); cleared by write 1 of the reported bit only | status latch set by event, cleared per knob int_clear (C3) | T12,T13: tests/test_irq.cpp; tests/test_power.cpp | OK |
| FLD-24.ONKEY_2SI | 0x24 ONKEY_INT_STAT0[2] ONKEY_2SI (RW1C, reset 0) | Table 105 p87 | Has(events, IrqSource::Onkey2s): returned by ServiceInterrupts(); cleared by write 1 of the reported bit only | status latch set by event, cleared per knob int_clear (C3) | T12,T13: tests/test_irq.cpp; tests/test_power.cpp | OK |
| FLD-24.ONKEY_3SI | 0x24 ONKEY_INT_STAT0[3] ONKEY_3SI (RW1C, reset 0) | Table 105 p87 | Has(events, IrqSource::Onkey3s): returned by ServiceInterrupts(); cleared by write 1 of the reported bit only | status latch set by event, cleared per knob int_clear (C3) | T12,T13: tests/test_irq.cpp; tests/test_power.cpp | OK |
| FLD-24.ONKEY_4SI | 0x24 ONKEY_INT_STAT0[4] ONKEY_4SI (RW1C, reset 0) | Table 105 p87 | Has(events, IrqSource::Onkey4s): returned by ServiceInterrupts(); cleared by write 1 of the reported bit only | status latch set by event, cleared per knob int_clear (C3) | T12,T13: tests/test_irq.cpp; tests/test_power.cpp | OK |
| FLD-24.ONKEY_8SI | 0x24 ONKEY_INT_STAT0[5] ONKEY_8SI (RW1C, reset 0) | Table 105 p87 | Has(events, IrqSource::Onkey8s): returned by ServiceInterrupts(); cleared by write 1 of the reported bit only | status latch set by event, cleared per knob int_clear (C3) | T12,T13: tests/test_irq.cpp; tests/test_power.cpp | OK |
| FLD-24.UNUSED | 0x24 ONKEY_INT_STAT0[7:6] UNUSED (—, reset —) | Table 105 p87 | not exposed: reserved/unused; kept by read-modify-write, never forced | register file stores the bit | T03: tests/test_configure.cpp | INFO |
| FLD-25.ONKEY_PUSHM | 0x25 ONKEY_INT_MASK0[0] ONKEY_PUSHM (RW, reset 1) | Table 106 p88 | IrqMask.masked[group] bit ONKEY_PUSHM (1 = masked, reset 1); driver unmasks only requested sources | mask gates INTB only; status still sets | T12: tests/test_irq.cpp | OK |
| FLD-25.ONKEY_1SM | 0x25 ONKEY_INT_MASK0[1] ONKEY_1SM (RW, reset 1) | Table 106 p88 | IrqMask.masked[group] bit ONKEY_1SM (1 = masked, reset 1); driver unmasks only requested sources | mask gates INTB only; status still sets | T12: tests/test_irq.cpp | OK |
| FLD-25.ONKEY_2SM | 0x25 ONKEY_INT_MASK0[2] ONKEY_2SM (RW, reset 1) | Table 106 p88 | IrqMask.masked[group] bit ONKEY_2SM (1 = masked, reset 1); driver unmasks only requested sources | mask gates INTB only; status still sets | T12: tests/test_irq.cpp | OK |
| FLD-25.ONKEY_3SM | 0x25 ONKEY_INT_MASK0[3] ONKEY_3SM (RW, reset 1) | Table 106 p88 | IrqMask.masked[group] bit ONKEY_3SM (1 = masked, reset 1); driver unmasks only requested sources | mask gates INTB only; status still sets | T12: tests/test_irq.cpp | OK |
| FLD-25.ONKEY_4SM | 0x25 ONKEY_INT_MASK0[4] ONKEY_4SM (RW, reset 1) | Table 106 p88 | IrqMask.masked[group] bit ONKEY_4SM (1 = masked, reset 1); driver unmasks only requested sources | mask gates INTB only; status still sets | T12: tests/test_irq.cpp | OK |
| FLD-25.ONKEY_8SM | 0x25 ONKEY_INT_MASK0[5] ONKEY_8SM (RW, reset 1) | Table 106 p88 | IrqMask.masked[group] bit ONKEY_8SM (1 = masked, reset 1); driver unmasks only requested sources | mask gates INTB only; status still sets | T12: tests/test_irq.cpp | OK |
| FLD-25.UNUSED | 0x25 ONKEY_INT_MASK0[7:6] UNUSED (—, reset —) | Table 106 p88 | not exposed: reserved/unused; kept by read-modify-write, never forced | register file stores the bit | T03: tests/test_configure.cpp | INFO |
| FLD-26.ONKEY_PUSHS | 0x26 ONKEY_INT_SENSE0[0] ONKEY_PUSHS (R, reset 0) | Table 107 p89 | Snapshot.sense[group] bit ONKEY_PUSHS (ReadSense()): read only, not latched | live level | T12,T22: tests/test_irq.cpp | OK |
| FLD-26.ONKEY_1SS | 0x26 ONKEY_INT_SENSE0[1] ONKEY_1SS (R, reset 0) | Table 107 p89 | Snapshot.sense[group] bit ONKEY_1SS (ReadSense()): read only, not latched | live level | T12,T22: tests/test_irq.cpp | OK |
| FLD-26.ONKEY_2SS | 0x26 ONKEY_INT_SENSE0[2] ONKEY_2SS (R, reset 0) | Table 107 p89 | Snapshot.sense[group] bit ONKEY_2SS (ReadSense()): read only, not latched | live level | T12,T22: tests/test_irq.cpp | OK |
| FLD-26.ONKEY_3SS | 0x26 ONKEY_INT_SENSE0[3] ONKEY_3SS (R, reset 0) | Table 107 p89 | Snapshot.sense[group] bit ONKEY_3SS (ReadSense()): read only, not latched | live level | T12,T22: tests/test_irq.cpp | OK |
| FLD-26.ONKEY_4SS | 0x26 ONKEY_INT_SENSE0[4] ONKEY_4SS (R, reset 0) | Table 107 p89 | Snapshot.sense[group] bit ONKEY_4SS (ReadSense()): read only, not latched | live level | T12,T22: tests/test_irq.cpp | OK |
| FLD-26.ONKEY_8SS | 0x26 ONKEY_INT_SENSE0[5] ONKEY_8SS (R, reset 0) | Table 107 p89 | Snapshot.sense[group] bit ONKEY_8SS (ReadSense()): read only, not latched | live level | T12,T22: tests/test_irq.cpp | OK |
| FLD-26.UNUSED | 0x26 ONKEY_INT_SENSE0[7:6] UNUSED (—, reset —) | Table 107 p89 | not exposed: reserved/unused; kept by read-modify-write, never forced | register file stores the bit | T03: tests/test_configure.cpp | INFO |
| FLD-28.PWRUP_I | 0x28 MISC_INT_STAT0[0] PWRUP_I (RW1C, reset 0) | Table 108 p89 | Has(events, IrqSource::PowerUp): returned by ServiceInterrupts(); cleared by write 1 of the reported bit only | status latch set by event, cleared per knob int_clear (C3) | T12,T13: tests/test_irq.cpp; tests/test_power.cpp | OK |
| FLD-28.PWRDN_I | 0x28 MISC_INT_STAT0[1] PWRDN_I (RW1C, reset 0) | Table 108 p89 | Has(events, IrqSource::PowerDown): returned by ServiceInterrupts(); cleared by write 1 of the reported bit only | status latch set by event, cleared per knob int_clear (C3) | T12,T13: tests/test_irq.cpp; tests/test_power.cpp | OK |
| FLD-28.PWRON_I | 0x28 MISC_INT_STAT0[2] PWRON_I (RW1C, reset 0) | Table 108 p89 | Has(events, IrqSource::PwronChange): returned by ServiceInterrupts(); cleared by write 1 of the reported bit only | status latch set by event, cleared per knob int_clear (C3) | T12,T13: tests/test_irq.cpp; tests/test_power.cpp | OK |
| FLD-28.LOW_SYS_WARN_I | 0x28 MISC_INT_STAT0[3] LOW_SYS_WARN_I (RW1C, reset 0) | Table 108 p89 | Has(events, IrqSource::LowSysWarning): returned by ServiceInterrupts(); cleared by write 1 of the reported bit only | status latch set by event, cleared per knob int_clear (C3) | T12,T13: tests/test_irq.cpp; tests/test_power.cpp | OK |
| FLD-28.SYS_OVLO_I | 0x28 MISC_INT_STAT0[4] SYS_OVLO_I (RW1C, reset 0) | Table 108 p89 | Has(events, IrqSource::SysOvervoltage): returned by ServiceInterrupts(); cleared by write 1 of the reported bit only | status latch set by event, cleared per knob int_clear (C3) | T12,T13: tests/test_irq.cpp; tests/test_power.cpp | OK |
| FLD-28.UNUSED | 0x28 MISC_INT_STAT0[7:5] UNUSED (—, reset —) | Table 108 p89 | not exposed: reserved/unused; kept by read-modify-write, never forced | register file stores the bit | T03: tests/test_configure.cpp | INFO |
| FLD-29.PWRUP_M | 0x29 MISC_INT_MASK0[0] PWRUP_M (RW, reset 1) | Table 109 p90 | UnmaskOnly({IrqSource::PowerUp}) (1 = masked, reset 1); driver unmasks only requested sources | mask gates INTB only; status still sets | T12: tests/test_irq.cpp | OK |
| FLD-29.PWRDN_M | 0x29 MISC_INT_MASK0[1] PWRDN_M (RW, reset 1) | Table 109 p90 | UnmaskOnly({IrqSource::PowerDown}) (1 = masked, reset 1); driver unmasks only requested sources | mask gates INTB only; status still sets | T12: tests/test_irq.cpp | OK |
| FLD-29.PWRON_M | 0x29 MISC_INT_MASK0[2] PWRON_M (RW, reset 1) | Table 109 p90 | UnmaskOnly({IrqSource::PwronChange}) (1 = masked, reset 1); driver unmasks only requested sources | mask gates INTB only; status still sets | T12: tests/test_irq.cpp | OK |
| FLD-29.LOW_SYS_WARN_M | 0x29 MISC_INT_MASK0[3] LOW_SYS_WARN_M (RW, reset 1) | Table 109 p90 | UnmaskOnly({IrqSource::LowSysWarning}) (1 = masked, reset 1); driver unmasks only requested sources | mask gates INTB only; status still sets | T12: tests/test_irq.cpp | OK |
| FLD-29.SYS_OVLO_M | 0x29 MISC_INT_MASK0[4] SYS_OVLO_M (RW, reset 1) | Table 109 p90 | UnmaskOnly({IrqSource::SysOvervoltage}) (1 = masked, reset 1); driver unmasks only requested sources | mask gates INTB only; status still sets | T12: tests/test_irq.cpp | OK |
| FLD-29.UNUSED | 0x29 MISC_INT_MASK0[7:5] UNUSED (—, reset —) | Table 109 p90 | not exposed: reserved/unused; kept by read-modify-write, never forced | register file stores the bit | T03: tests/test_configure.cpp | INFO |
| FLD-2A.PWRUP_S | 0x2A MISC_INT_SENSE0[0] PWRUP_S (R, reset 0) | Table 110 p90 | Snapshot.sense[group] bit PWRUP (ReadSense()): read only, not latched | live level | T12,T22: tests/test_irq.cpp | OK |
| FLD-2A.PWRDN_S | 0x2A MISC_INT_SENSE0[1] PWRDN_S (R, reset 0) | Table 110 p90 | Snapshot.sense[group] bit PWRDN (ReadSense()): read only, not latched | live level | T12,T22: tests/test_irq.cpp | OK |
| FLD-2A.PWRON_S | 0x2A MISC_INT_SENSE0[2] PWRON_S (R, reset 0) | Table 110 p90 | Snapshot.sense[group] bit PWRON (ReadSense()): read only, not latched | live level | T12,T22: tests/test_irq.cpp | OK |
| FLD-2A.LOW_SYS_WARN_S | 0x2A MISC_INT_SENSE0[3] LOW_SYS_WARN_S (R, reset 0) | Table 110 p90 | Snapshot.sense[group] bit LOW_SYS_WARN (ReadSense()): read only, not latched | live level | T12,T22: tests/test_irq.cpp | OK |
| FLD-2A.SYS_OVLO_S | 0x2A MISC_INT_SENSE0[4] SYS_OVLO_S (R, reset 0) | Table 110 p90 | Snapshot.sense[group] bit SYS_OVLO (ReadSense()): read only, not latched | live level | T12,T22: tests/test_irq.cpp | OK |
| FLD-2A.UNUSED | 0x2A MISC_INT_SENSE0[7:5] UNUSED (—, reset —) | Table 110 p90 | not exposed: reserved/unused; kept by read-modify-write, never forced | register file stores the bit | T03: tests/test_configure.cpp | INFO |
| FLD-30.VCOIN | 0x30 COINCELL_CONTROL[3:0] VCOIN (RW, reset 0000) | Table 111 p91 | CoinCell.voltage_mv (1800..3300 step 100); code > 0 needs Limits.coin_cell_max_mv >= 3300 (C40) | VCOIN stored, no knob (C40 open; the 3.3 V = 1111 reading) | T18: tests/test_power.cpp; tests/test_configure.cpp | OK |
| FLD-30.COINCHEN | 0x30 COINCELL_CONTROL[4] COINCHEN (RW, reset 0) | Table 111 p91 | CoinCell.charge_enable, ack coin_cell_is_rechargeable | COINCHEN stored; LICELL charges to VCOIN while COINCHEN is set | T18,T05: tests/test_power.cpp; tests/test_configure.cpp; tests/test_config.cpp | OK |
| FLD-30.UNUSED | 0x30 COINCELL_CONTROL[7:5] UNUSED (—, reset —) | Table 111 p91 | not exposed: reserved/unused; kept by read-modify-write, never forced | register file stores the bit | T03: tests/test_configure.cpp | INFO |
| FLD-32.SW1_VOLT | 0x32 SW1_VOLT[5:0] SW1_VOLT (RW1S, reset —) | Table 112 p91 | BuckConfig(SW1).run_uv; SetRailVoltage; only when declared DVS (C1) | DVS table or fixed table by option | T01,T14: tests/test_config.cpp; inc/pf1550_codec.hpp (static_assert); tests/test_rails.cpp; tests/test_configure.cpp | OK |
| FLD-32.UNUSED | 0x32 SW1_VOLT[7:5] UNUSED (—, reset —) | Table 112 p91 | not exposed: reserved/unused; kept by read-modify-write, never forced | register file stores the bit | T03: tests/test_configure.cpp | INFO |
| FLD-33.SW1_STBY_VOLT | 0x33 SW1_STBY_VOLT[5:0] SW1_STBY_VOLT (RW1S, reset —) | Table 113 p91 | BuckConfig(SW1).standby_uv (optional); DVS only | as above | T01,T14: tests/test_config.cpp; inc/pf1550_codec.hpp (static_assert); tests/test_rails.cpp; tests/test_configure.cpp | OK |
| FLD-33.UNUSED | 0x33 SW1_STBY_VOLT[7:6] UNUSED (—, reset —) | Table 113 p91 | not exposed: reserved/unused; kept by read-modify-write, never forced | register file stores the bit | T03: tests/test_configure.cpp | INFO |
| FLD-34.SW1_SLP_VOLT | 0x34 SW1_SLP_VOLT[5:0] SW1_SLP_VOLT (RW1S, reset —) | Table 114 p92 | BuckConfig(SW1).sleep_uv (optional); DVS only | as above | T01,T14: tests/test_config.cpp; inc/pf1550_codec.hpp (static_assert); tests/test_rails.cpp; tests/test_configure.cpp | OK |
| FLD-34.UNUSED | 0x34 SW1_SLP_VOLT[7:6] UNUSED (—, reset —) | Table 114 p92 | not exposed: reserved/unused; kept by read-modify-write, never forced | register file stores the bit | T03: tests/test_configure.cpp | INFO |
| FLD-35.SW1_EN | 0x35 SW1_CTRL[0] SW1_EN (RW1S, reset 0) | Table 115 p92 | BuckConfig(SW1).modes.run | enable in RUN (T30) | T14,T06: tests/test_rails.cpp; tests/test_configure.cpp | OK |
| FLD-35.SW1_STBY_EN | 0x35 SW1_CTRL[1] SW1_STBY_EN (RW1S, reset 0) | Table 115 p92 | BuckConfig(SW1).modes.standby | enable in STANDBY (T30) | T14: tests/test_rails.cpp; tests/test_configure.cpp | OK |
| FLD-35.SW1_OMODE | 0x35 SW1_CTRL[2] SW1_OMODE (RW, reset 0) | Table 115 p92 | BuckConfig(SW1).modes.sleep (enable in SLEEP) | enable in SLEEP (T30) | T14: tests/test_rails.cpp; tests/test_configure.cpp | OK |
| FLD-35.SW1_LPWR | 0x35 SW1_CTRL[3] SW1_LPWR (RW, reset 0) | Table 115 p92 | BuckConfig(SW1).modes.low_power | low-power in STANDBY/SLEEP (T30) | T14: tests/test_rails.cpp; tests/test_configure.cpp | OK |
| FLD-35.SW1_DVSSPEED | 0x35 SW1_CTRL[4] SW1_DVSSPEED (RW1S, reset 0) | Table 115 p92 | BuckConfig(SW1).dvs_speed {2us, 4us} per 12.5 mV | DVS step time | T14: tests/test_rails.cpp; tests/test_configure.cpp | OK |
| FLD-35.SW1_FPWM_IN_DVS | 0x35 SW1_CTRL[5] SW1_FPWM_IN_DVS (RW, reset 0) | Table 115 p92 | BuckConfig(SW1).fpwm_in_dvs | flag stored; CCM in DVS down | T14: tests/test_rails.cpp; tests/test_configure.cpp | OK |
| FLD-35.SW1_FPWM | 0x35 SW1_CTRL[6] SW1_FPWM (RW, reset 0) | Table 115 p92 | BuckConfig(SW1).fpwm | forced PWM flag | T14: tests/test_rails.cpp; tests/test_configure.cpp | OK |
| FLD-35.SW1_RDIS_ENB | 0x35 SW1_CTRL[7] SW1_RDIS_ENB (RW1S, reset 0) | Table 115 p92 | BuckConfig(SW1).output_discharge (inverted: RDIS_ENB 1 = no discharge) | discharge resistor flag | T14: tests/test_rails.cpp; tests/test_configure.cpp | OK |
| FLD-36.SW1_ILIM | 0x36 SW1_CTRL1[1:0] SW1_ILIM (RW1S, reset 00) | Table 116 p93 | BuckConfig(SW1).current_limit {1.0, 1.2, 1.5, 2.0} A | limit level; fault injected by test | T01,T15: tests/test_config.cpp; inc/pf1550_codec.hpp (static_assert); tests/test_irq.cpp; tests/test_rails.cpp | OK |
| FLD-36.UNUSED | 0x36 SW1_CTRL1[3:2] UNUSED (—, reset —) | Table 116 p93 | not exposed: reserved/unused; kept by read-modify-write, never forced | register file stores the bit | T03: tests/test_configure.cpp | INFO |
| FLD-36.SW1_TMODE_SEL | 0x36 SW1_CTRL1[4] SW1_TMODE_SEL (RW, reset 0) | Table 116 p93 | not exposed: control-loop option, data sheet gives no selection guidance | register file stores the bit; write attempts rejected by the access table | T04: tests/test_model.cpp; tests/test_configure.cpp | INFO |
| FLD-36.UNUSED[7:5] | 0x36 SW1_CTRL1[7:5] UNUSED (—, reset —) | Table 116 p93 | not exposed: reserved/unused; kept by read-modify-write, never forced | register file stores the bit | T03: tests/test_configure.cpp | INFO |
| FLD-38.SW2_VOLT | 0x38 SW2_VOLT[5:0] SW2_VOLT (RW1S, reset —) | Table 117 p93 | BuckConfig(SW2).run_uv; SetRailVoltage; only when declared DVS (C1) | DVS table or fixed table by option | T01,T14: tests/test_config.cpp; inc/pf1550_codec.hpp (static_assert); tests/test_rails.cpp; tests/test_configure.cpp | OK |
| FLD-38.UNUSED | 0x38 SW2_VOLT[7:6] UNUSED (—, reset —) | Table 117 p93 | not exposed: reserved/unused; kept by read-modify-write, never forced | register file stores the bit | T03: tests/test_configure.cpp | INFO |
| FLD-39.SW2_STBY_VOLT | 0x39 SW2_STBY_VOLT[5:0] SW2_STBY_VOLT (RW1S, reset —) | Table 118 p93 | BuckConfig(SW2).standby_uv (optional); DVS only | as above | T01,T14: tests/test_config.cpp; inc/pf1550_codec.hpp (static_assert); tests/test_rails.cpp; tests/test_configure.cpp | OK |
| FLD-39.UNUSED | 0x39 SW2_STBY_VOLT[7:6] UNUSED (—, reset —) | Table 118 p93 | not exposed: reserved/unused; kept by read-modify-write, never forced | register file stores the bit | T03: tests/test_configure.cpp | INFO |
| FLD-3A.SW2_SLP_VOLT | 0x3A SW2_SLP_VOLT[5:0] SW2_SLP_VOLT (RW1S, reset —) | Table 119 p93 | BuckConfig(SW2).sleep_uv (optional); DVS only | as above | T01,T14: tests/test_config.cpp; inc/pf1550_codec.hpp (static_assert); tests/test_rails.cpp; tests/test_configure.cpp | OK |
| FLD-3A.UNUSED | 0x3A SW2_SLP_VOLT[7:6] UNUSED (—, reset —) | Table 119 p93 | not exposed: reserved/unused; kept by read-modify-write, never forced | register file stores the bit | T03: tests/test_configure.cpp | INFO |
| FLD-3B.SW2_EN | 0x3B SW2_CTRL[0] SW2_EN (RW1S, reset 0) | Table 120 p94 | BuckConfig(SW2).modes.run | enable in RUN (T30) | T14,T06: tests/test_rails.cpp; tests/test_configure.cpp | OK |
| FLD-3B.SW2_STBY_EN | 0x3B SW2_CTRL[1] SW2_STBY_EN (RW1S, reset 0) | Table 120 p94 | BuckConfig(SW2).modes.standby | enable in STANDBY (T30) | T14: tests/test_rails.cpp; tests/test_configure.cpp | OK |
| FLD-3B.SW2_OMODE | 0x3B SW2_CTRL[2] SW2_OMODE (RW, reset 0) | Table 120 p94 | BuckConfig(SW2).modes.sleep (enable in SLEEP) | enable in SLEEP (T30) | T14: tests/test_rails.cpp; tests/test_configure.cpp | OK |
| FLD-3B.SW2_LPWR | 0x3B SW2_CTRL[3] SW2_LPWR (RW, reset 0) | Table 120 p94 | BuckConfig(SW2).modes.low_power | low-power in STANDBY/SLEEP (T30) | T14: tests/test_rails.cpp; tests/test_configure.cpp | OK |
| FLD-3B.SW2_DVSSPEED | 0x3B SW2_CTRL[4] SW2_DVSSPEED (RW1S, reset 0) | Table 120 p94 | BuckConfig(SW2).dvs_speed {2us, 4us} per 12.5 mV | DVS step time | T14: tests/test_rails.cpp; tests/test_configure.cpp | OK |
| FLD-3B.SW2_FPWM_IN_DVS | 0x3B SW2_CTRL[5] SW2_FPWM_IN_DVS (RW, reset 0) | Table 120 p94 | BuckConfig(SW2).fpwm_in_dvs | flag stored; CCM in DVS down | T14: tests/test_rails.cpp; tests/test_configure.cpp | OK |
| FLD-3B.SW2_FPWM | 0x3B SW2_CTRL[6] SW2_FPWM (RW, reset 0) | Table 120 p94 | BuckConfig(SW2).fpwm | forced PWM flag | T14: tests/test_rails.cpp; tests/test_configure.cpp | OK |
| FLD-3B.SW2_RDIS_ENB | 0x3B SW2_CTRL[7] SW2_RDIS_ENB (RW1S, reset 0) | Table 120 p94 | BuckConfig(SW2).output_discharge (inverted: RDIS_ENB 1 = no discharge) | discharge resistor flag | T14: tests/test_rails.cpp; tests/test_configure.cpp | OK |
| FLD-3C.SW2_ILIM | 0x3C SW2_CTRL1[1:0] SW2_ILIM (RW1S, reset 00) | Table 121 p94 | BuckConfig(SW2).current_limit {1.0, 1.2, 1.5, 2.0} A | limit level; fault injected by test | T01,T15: tests/test_config.cpp; inc/pf1550_codec.hpp (static_assert); tests/test_irq.cpp; tests/test_rails.cpp | OK |
| FLD-3C.UNUSED | 0x3C SW2_CTRL1[3:2] UNUSED (—, reset —) | Table 121 p94 | not exposed: reserved/unused; kept by read-modify-write, never forced | register file stores the bit | T03: tests/test_configure.cpp | INFO |
| FLD-3C.SW2_TMODE_SEL | 0x3C SW2_CTRL1[4] SW2_TMODE_SEL (RW, reset 0) | Table 121 p94 | not exposed: control-loop option, data sheet gives no selection guidance | register file stores the bit; write attempts rejected by the access table | T04: tests/test_model.cpp; tests/test_configure.cpp | INFO |
| FLD-3C.UNUSED[7:5] | 0x3C SW2_CTRL1[7:5] UNUSED (—, reset —) | Table 121 p94 | not exposed: reserved/unused; kept by read-modify-write, never forced | register file stores the bit | T03: tests/test_configure.cpp | INFO |
| FLD-3E.SW3_VOLT | 0x3E SW3_VOLT[3:0] SW3_VOLT (RW1S, reset —) | Table 122 p95 | ReadRail(Rail::Sw3) read only; never written (6.3.3, C2) | loaded from OTP; write ignored (knob) | T01,T04,T14: tests/test_config.cpp; inc/pf1550_codec.hpp (static_assert); tests/test_model.cpp; tests/test_configure.cpp; tests/test_rails.cpp | OK |
| FLD-3E.UNUSED | 0x3E SW3_VOLT[7:4] UNUSED (—, reset —) | Table 122 p95 | not exposed: reserved/unused; kept by read-modify-write, never forced | register file stores the bit | T03: tests/test_configure.cpp | INFO |
| FLD-3F.SW3_STBY_VOLT | 0x3F SW3_STBY_VOLT[3:0] SW3_STBY_VOLT (RW1S, reset —) | Table 123 p95 | ReadRail(Rail::Sw3) read only; never written (6.3.3, C2) | loaded from OTP; write ignored (knob) | T01,T04,T14: tests/test_config.cpp; inc/pf1550_codec.hpp (static_assert); tests/test_model.cpp; tests/test_configure.cpp; tests/test_rails.cpp | OK |
| FLD-3F.UNUSED | 0x3F SW3_STBY_VOLT[7:4] UNUSED (—, reset —) | Table 123 p95 | not exposed: reserved/unused; kept by read-modify-write, never forced | register file stores the bit | T03: tests/test_configure.cpp | INFO |
| FLD-40.SW3_SLP_VOLT | 0x40 SW3_SLP_VOLT[3:0] SW3_SLP_VOLT (RW1S, reset —) | Table 124 p95 | ReadRail(Rail::Sw3) read only; never written (6.3.3, C2) | loaded from OTP; write ignored (knob) | T01,T04,T14: tests/test_config.cpp; inc/pf1550_codec.hpp (static_assert); tests/test_model.cpp; tests/test_configure.cpp; tests/test_rails.cpp | OK |
| FLD-40.UNUSED | 0x40 SW3_SLP_VOLT[7:4] UNUSED (—, reset —) | Table 124 p95 | not exposed: reserved/unused; kept by read-modify-write, never forced | register file stores the bit | T03: tests/test_configure.cpp | INFO |
| FLD-41.SW3_EN | 0x41 SW3_CTRL[0] SW3_EN (RW1S, reset 0) | Table 125 p95 | BuckConfig(SW3).modes.run | enable in RUN (T36) | T14,T06: tests/test_rails.cpp; tests/test_configure.cpp | OK |
| FLD-41.SW3_STBY_EN | 0x41 SW3_CTRL[1] SW3_STBY_EN (RW1S, reset 0) | Table 125 p95 | BuckConfig(SW3).modes.standby | T36 | T14: tests/test_rails.cpp; tests/test_configure.cpp | OK |
| FLD-41.SW3_OMODE | 0x41 SW3_CTRL[2] SW3_OMODE (RW, reset 0) | Table 125 p95 | BuckConfig(SW3).modes.sleep | T36 | T14: tests/test_rails.cpp; tests/test_configure.cpp | OK |
| FLD-41.SW3_LPWR | 0x41 SW3_CTRL[3] SW3_LPWR (RW, reset 0) | Table 125 p95 | BuckConfig(SW3).modes.low_power | T36 | T14: tests/test_rails.cpp; tests/test_configure.cpp | OK |
| FLD-41.UNUSED | 0x41 SW3_CTRL[4] UNUSED (—, reset —) | Table 125 p95 | not exposed: reserved/unused; kept by read-modify-write, never forced | register file stores the bit | T03: tests/test_configure.cpp | INFO |
| FLD-41.UNUSED[5] | 0x41 SW3_CTRL[5] UNUSED (—, reset —) | Table 125 p95 | not exposed: reserved/unused; kept by read-modify-write, never forced | register file stores the bit | T03: tests/test_configure.cpp | INFO |
| FLD-41.SW3_FPWM | 0x41 SW3_CTRL[6] SW3_FPWM (RW, reset 0) | Table 125 p95 | BuckConfig(SW3).fpwm | forced PWM flag | T14: tests/test_rails.cpp; tests/test_configure.cpp | OK |
| FLD-41.SW3_RDIS_ENB | 0x41 SW3_CTRL[7] SW3_RDIS_ENB (RW1S, reset 0) | Table 125 p95 | BuckConfig(SW3).output_discharge (inverted) | discharge flag | T14: tests/test_rails.cpp; tests/test_configure.cpp | OK |
| FLD-42.SW3_ILIM | 0x42 SW3_CTRL1[1:0] SW3_ILIM (RW1S, reset 00) | Table 126 p96 | BuckConfig(SW3).current_limit | limit level | T01,T15: tests/test_config.cpp; inc/pf1550_codec.hpp (static_assert); tests/test_irq.cpp; tests/test_rails.cpp | OK |
| FLD-42.UNUSED | 0x42 SW3_CTRL1[3:2] UNUSED (—, reset —) | Table 126 p96 | not exposed: reserved/unused; kept by read-modify-write, never forced | register file stores the bit | T03: tests/test_configure.cpp | INFO |
| FLD-42.SW3_TMODE_SEL | 0x42 SW3_CTRL1[4] SW3_TMODE_SEL (RW, reset 0) | Table 126 p96 | not exposed: control-loop option | register file stores the bit; write attempts rejected by the access table | T04: tests/test_model.cpp; tests/test_configure.cpp | INFO |
| FLD-42.UNUSED[7:5] | 0x42 SW3_CTRL1[7:5] UNUSED (—, reset —) | Table 126 p96 | not exposed: reserved/unused; kept by read-modify-write, never forced | register file stores the bit | T03: tests/test_configure.cpp | INFO |
| FLD-48.VSNVS_VOLT | 0x48 VSNVS_CTRL[2:0] VSNVS_VOLT (RW1S, reset 000) | Table 127 p96 | not exposed: "not used in PF1550" (T127) | register file stores the bit; write attempts rejected by the access table | T04: tests/test_model.cpp; tests/test_configure.cpp | INFO |
| FLD-48.CLKPULSE | 0x48 VSNVS_CTRL[3] CLKPULSE (RW, reset 0) | Table 127 p96 | not exposed: evaluation bit | register file stores the bit; write attempts rejected by the access table | T04: tests/test_model.cpp; tests/test_configure.cpp | INFO |
| FLD-48.FORCEBOS | 0x48 VSNVS_CTRL[4] FORCEBOS (RW, reset 0) | Table 127 p96 | not exposed: evaluation bit | register file stores the bit; write attempts rejected by the access table | T04: tests/test_model.cpp; tests/test_configure.cpp | INFO |
| FLD-48.LIBGDIS | 0x48 VSNVS_CTRL[5] LIBGDIS (RW, reset 0) | Table 127 p96 | VsnvsConfig.local_bandgap_disable | flag stored | T18: tests/test_power.cpp; tests/test_configure.cpp | OK |
| FLD-48.UNUSED | 0x48 VSNVS_CTRL[7:6] UNUSED (—, reset —) | Table 127 p96 | not exposed: reserved/unused; kept by read-modify-write, never forced | register file stores the bit | T03: tests/test_configure.cpp | INFO |
| FLD-4A.VREFDDR_EN | 0x4A VREFDDR_CTRL[0] VREFDDR_EN (RW1S, reset 0) | Table 128 p96 | VrefDdrConfig.modes.run | enable per mode | T18: tests/test_power.cpp; tests/test_configure.cpp | OK |
| FLD-4A.VREFDDR_STBY_EN | 0x4A VREFDDR_CTRL[1] VREFDDR_STBY_EN (RW1S, reset 0) | Table 128 p96 | VrefDdrConfig.modes.standby | enable per mode | T18: tests/test_power.cpp; tests/test_configure.cpp | OK |
| FLD-4A.VREFDDR_OMODE | 0x4A VREFDDR_CTRL[2] VREFDDR_OMODE (RW, reset 0) | Table 128 p96 | VrefDdrConfig.modes.sleep | enable per mode | T18: tests/test_power.cpp; tests/test_configure.cpp | OK |
| FLD-4A.VREFDDR_LPWR | 0x4A VREFDDR_CTRL[3] VREFDDR_LPWR (RW, reset 0) | Table 128 p96 | VrefDdrConfig.modes.low_power | enable per mode | T18: tests/test_power.cpp; tests/test_configure.cpp | OK |
| FLD-4A.UNUSED | 0x4A VREFDDR_CTRL[7:4] UNUSED (—, reset —) | Table 128 p96 | not exposed: reserved/unused; kept by read-modify-write, never forced | register file stores the bit | T03: tests/test_configure.cpp | INFO |
| FLD-4C.LDO1_VOLT | 0x4C LDO1_VOLT[4:0] LDO1_VOLT (RW1S, reset —) | Table 129 p97 | LdoConfig.volt (LDO1); SetRailVoltage inside RailLimits | code table (T41/T43) | T01,T14,T05: tests/test_config.cpp; inc/pf1550_codec.hpp (static_assert); tests/test_rails.cpp; tests/test_configure.cpp | OK |
| FLD-4C.UNUSED | 0x4C LDO1_VOLT[7:5] UNUSED (—, reset —) | Table 129 p97 | not exposed: reserved/unused; kept by read-modify-write, never forced | register file stores the bit | T03: tests/test_configure.cpp | INFO |
| FLD-4D.VLDO1_EN | 0x4D LDO1_CTRL[0] VLDO1_EN (RW1S, reset 0) | Table 130 p97 | LdoConfig(LDO1).modes.run | enable per mode (T42/T44) | T14: tests/test_rails.cpp; tests/test_configure.cpp | OK |
| FLD-4D.VLDO1_STBY_EN | 0x4D LDO1_CTRL[1] VLDO1_STBY_EN (RW1S, reset 0) | Table 130 p97 | LdoConfig(LDO1).modes.standby | enable per mode (T42/T44) | T14: tests/test_rails.cpp; tests/test_configure.cpp | OK |
| FLD-4D.VLDO1_OMODE | 0x4D LDO1_CTRL[2] VLDO1_OMODE (RW, reset 0) | Table 130 p97 | LdoConfig(LDO1).modes.sleep | enable per mode (T42/T44) | T14: tests/test_rails.cpp; tests/test_configure.cpp | OK |
| FLD-4D.VLDO1_LPWR | 0x4D LDO1_CTRL[3] VLDO1_LPWR (RW, reset 0) | Table 130 p97 | LdoConfig(LDO1).modes.low_power (needs ack load_below_10ma) | enable per mode (T42/T44) | T14,T05: tests/test_rails.cpp; tests/test_configure.cpp; tests/test_config.cpp | OK |
| FLD-4D.LDO1_LS_EN | 0x4D LDO1_CTRL[4] LDO1_LS_EN (RW1S, reset 0) | Table 130 p97 | EnableLoadSwitch(Rail::LDO1) one-way, token, no current limit in LS mode (7.2.6) | one-way latch, clear refused | T16,T14: tests/test_power.cpp; tests/test_rails.cpp; tests/test_review.cpp; tests/test_configure.cpp | OK |
| FLD-4D.UNUSED | 0x4D LDO1_CTRL[7:5] UNUSED (—, reset —) | Table 130 p97 | not exposed: reserved/unused; kept by read-modify-write, never forced | register file stores the bit | T03: tests/test_configure.cpp | INFO |
| FLD-4F.LDO2_VOLT | 0x4F LDO2_VOLT[3:0] LDO2_VOLT (RW1S, reset —) | Table 131 p97 | LdoConfig.volt (LDO2); SetRailVoltage inside RailLimits | code table (T41/T43) | T01,T14,T05: tests/test_config.cpp; inc/pf1550_codec.hpp (static_assert); tests/test_rails.cpp; tests/test_configure.cpp | OK |
| FLD-4F.UNUSED | 0x4F LDO2_VOLT[7:4] UNUSED (—, reset —) | Table 131 p97 | not exposed: reserved/unused; kept by read-modify-write, never forced | register file stores the bit | T03: tests/test_configure.cpp | INFO |
| FLD-50.VLDO2_EN | 0x50 LDO2_CTRL[0] VLDO2_EN (RW1S, reset 0) | Table 132 p98 | LdoConfig(LDO2).modes.run | enable per mode (T42/T44) | T14: tests/test_rails.cpp; tests/test_configure.cpp | OK |
| FLD-50.VLDO2_STBY_EN | 0x50 LDO2_CTRL[1] VLDO2_STBY_EN (RW1S, reset 0) | Table 132 p98 | LdoConfig(LDO2).modes.standby | enable per mode (T42/T44) | T14: tests/test_rails.cpp; tests/test_configure.cpp | OK |
| FLD-50.VLDO2_OMODE | 0x50 LDO2_CTRL[2] VLDO2_OMODE (RW, reset 0) | Table 132 p98 | LdoConfig(LDO2).modes.sleep | enable per mode (T42/T44) | T14: tests/test_rails.cpp; tests/test_configure.cpp | OK |
| FLD-50.VLDO2_LPWR | 0x50 LDO2_CTRL[3] VLDO2_LPWR (RW, reset 0) | Table 132 p98 | LdoConfig(LDO2).modes.low_power (needs ack load_below_10ma) | enable per mode (T42/T44) | T14,T05: tests/test_rails.cpp; tests/test_configure.cpp; tests/test_config.cpp | OK |
| FLD-50.UNUSED | 0x50 LDO2_CTRL[7:4] UNUSED (—, reset —) | Table 132 p98 | not exposed: reserved/unused; kept by read-modify-write, never forced | register file stores the bit | T03: tests/test_configure.cpp | INFO |
| FLD-52.LDO3_VOLT | 0x52 LDO3_VOLT[4:0] LDO3_VOLT (RW1S, reset —) | Table 133 p98 | LdoConfig.volt (LDO3); SetRailVoltage inside RailLimits | code table (T41/T43) | T01,T14,T05: tests/test_config.cpp; inc/pf1550_codec.hpp (static_assert); tests/test_rails.cpp; tests/test_configure.cpp | OK |
| FLD-52.UNUSED | 0x52 LDO3_VOLT[7:5] UNUSED (—, reset —) | Table 133 p98 | not exposed: reserved/unused; kept by read-modify-write, never forced | register file stores the bit | T03: tests/test_configure.cpp | INFO |
| FLD-53.VLDO3_EN | 0x53 LDO3_CTRL[0] VLDO3_EN (RW1S, reset 0) | Table 134 p98 | LdoConfig(LDO3).modes.run | enable per mode (T42/T44) | T14: tests/test_rails.cpp; tests/test_configure.cpp | OK |
| FLD-53.VLDO3_STBY_EN | 0x53 LDO3_CTRL[1] VLDO3_STBY_EN (RW1S, reset 0) | Table 134 p98 | LdoConfig(LDO3).modes.standby | enable per mode (T42/T44) | T14: tests/test_rails.cpp; tests/test_configure.cpp | OK |
| FLD-53.VLDO3_OMODE | 0x53 LDO3_CTRL[2] VLDO3_OMODE (RW, reset 0) | Table 134 p98 | LdoConfig(LDO3).modes.sleep | enable per mode (T42/T44) | T14: tests/test_rails.cpp; tests/test_configure.cpp | OK |
| FLD-53.VLDO3_LPWR | 0x53 LDO3_CTRL[3] VLDO3_LPWR (RW, reset 0) | Table 134 p98 | LdoConfig(LDO3).modes.low_power (needs ack load_below_10ma) | enable per mode (T42/T44) | T14,T05: tests/test_rails.cpp; tests/test_configure.cpp; tests/test_config.cpp | OK |
| FLD-53.LDO3_LS_EN | 0x53 LDO3_CTRL[4] LDO3_LS_EN (RW1S, reset 0) | Table 134 p98 | EnableLoadSwitch(Rail::LDO3) one-way, token, no current limit in LS mode (7.2.6) | one-way latch, clear refused | T16,T14: tests/test_power.cpp; tests/test_rails.cpp; tests/test_review.cpp; tests/test_configure.cpp | OK |
| FLD-53.UNUSED | 0x53 LDO3_CTRL[7:5] UNUSED (—, reset —) | Table 134 p98 | not exposed: reserved/unused; kept by read-modify-write, never forced | register file stores the bit | T03: tests/test_configure.cpp | INFO |
| FLD-58.STANDBYDLY | 0x58 PWRCTRL0[1:0] STANDBYDLY (RW, reset 01) | Table 135 p99 | PowerConfig.standby_delay | delay before STANDBY (T76 text) | T13,T23: tests/test_power.cpp; tests/test_configure.cpp | OK |
| FLD-58.STANDBYINV | 0x58 PWRCTRL0[2] STANDBYINV (RW, reset 0) | Table 135 p99 | PowerConfig.standby_inverted | pin polarity (T76) | T13,T23: tests/test_power.cpp; tests/test_configure.cpp | OK |
| FLD-58.POR_DLY | 0x58 PWRCTRL0[5:3] POR_DLY (RW1S, reset 000) | Table 135 p99 | not exposed: OTP-loaded RESETBMCU delay, code 001 undefined (C30) | register file stores the bit; write attempts rejected by the access table | T04: tests/test_model.cpp; tests/test_configure.cpp | INFO |
| FLD-58.TGRESET | 0x58 PWRCTRL0[7:6] TGRESET (RW1S, reset 00) | Table 135 p99 | PowerConfig.global_reset {4,8,12,16}; ack hard_reset_paths (C42) | Table 83 G/I long-press time | T13,T05: tests/test_power.cpp; tests/test_config.cpp | OK |
| FLD-59.PWRONDBNC | 0x59 PWRCTRL1[1:0] PWRONDBNC (RW, reset 00) | Table 136 p99 | PowerConfig.pwron_debounce (31.25, 125, 750 ms; codes 00 and 01 equal, C41) | T75 debounce | T13,T20: tests/test_power.cpp; tests/test_configure.cpp | OK |
| FLD-59.ONKEYDBNC | 0x59 PWRCTRL1[3:2] ONKEYDBNC (RW, reset 00) | Table 136 p99 | PowerConfig.onkey_debounce (same grid) | T82 debounce | T13,T20: tests/test_power.cpp; tests/test_configure.cpp | OK |
| FLD-59.PWRONRSTEN | 0x59 PWRCTRL1[4] PWRONRSTEN (RW, reset 0) | Table 136 p99 | PowerConfig.pwron_long_press_reset; ack hard_reset_paths | Table 83 C/F/G | T13,T05: tests/test_power.cpp; tests/test_config.cpp | OK |
| FLD-59.RESTARTEN | 0x59 PWRCTRL1[5] RESTARTEN (RW, reset 0) | Table 136 p99 | PowerConfig.restart_on_long_press; ack hard_reset_paths | Table 83 H | T13,T05: tests/test_power.cpp; tests/test_config.cpp | OK |
| FLD-59.REGSCPEN | 0x59 PWRCTRL1[6] REGSCPEN (RW, reset 0) | Table 136 p99 | PowerConfig.ldo_off_on_current_limit | LDO off on limit fault | T15: tests/test_irq.cpp; tests/test_rails.cpp | OK |
| FLD-59.ONKEY_RST_EN | 0x59 PWRCTRL1[7] ONKEY_RST_EN (RW, reset 1) | Table 136 p99 | PowerConfig.onkey_reset; ack hard_reset_paths | Table 83 G/I | T13,T05: tests/test_power.cpp; tests/test_config.cpp | OK |
| FLD-5A.UVDET | 0x5A PWRCTRL2[1:0] UVDET (RW1S, reset 00) | Table 137 p100 | PowerConfig.uvdet {2.65..3.1 V rising, T137}; ack undervoltage_threshold | VSYS comparator with falling thresholds (C29) | T13,T23,T05: tests/test_power.cpp; tests/test_configure.cpp; tests/test_config.cpp | OK |
| FLD-5A.LOW_SYS_WARN | 0x5A PWRCTRL2[3:2] LOW_SYS_WARN (RW, reset 00) | Table 137 p100 | PowerConfig.low_sys_warn | warning interrupt on VSYS | T13,T23: tests/test_power.cpp; tests/test_configure.cpp | OK |
| FLD-5A.UNUSED | 0x5A PWRCTRL2[7:4] UNUSED (—, reset —) | Table 137 p100 | not exposed: reserved/unused; kept by read-modify-write, never forced | register file stores the bit | T03: tests/test_configure.cpp | INFO |
| FLD-5B.GOTO_SHIP | 0x5B PWRCTRL3[0] GOTO_SHIP (RW, reset 0) | Table 138 p100 | EnterShip(ShipConfirm): preconditions in 2.5 (C6) | Table 83 G then J; no knob (C6: SHIP only without VBUS, the driver refuses the call with VBUS valid) | T16: tests/test_power.cpp; tests/test_rails.cpp; tests/test_review.cpp | OK |
| FLD-5B.GOTO_CORE_OFF | 0x5B PWRCTRL3[1] GOTO_CORE_OFF (RW, reset 0) | Table 138 p100 | EnterCoreOff(CoreOffConfirm): preconditions in 2.5 (C7) | Table 83 I, K | T16: tests/test_power.cpp; tests/test_rails.cpp; tests/test_review.cpp | OK |
| FLD-5B.UNUSED | 0x5B PWRCTRL3[7:2] UNUSED (—, reset —) | Table 138 p100 | not exposed: reserved/unused; kept by read-modify-write, never forced | register file stores the bit | T03: tests/test_configure.cpp | INFO |
| FLD-5F.SW1_PWRDN_SEQ | 0x5F SW1_PWRDN_SEQ[2:0] SW1_PWRDN_SEQ (RW1S, reset 000) | Table 139 p101 | ReadPowerDownSequence(), SetPowerDownSequence() (needs power_down_order_reviewed), PowerDownDelayUs() | power-down order mirrors the power-up order after reset; the model runs the schedule | T03,T04: tests/test_configure.cpp; tests/test_model.cpp | OK |
| FLD-5F.UNUSED | 0x5F SW1_PWRDN_SEQ[7:3] UNUSED (—, reset —) | Table 139 p101 | not exposed: reserved/unused; kept by read-modify-write, never forced | register file stores the bit | T03: tests/test_configure.cpp | INFO |
| FLD-60.SW2_PWRDN_SEQ | 0x60 SW2_PWRDN_SEQ[2:0] SW2_PWRDN_SEQ (RW1S, reset 000) | Table 140 p101 | ReadPowerDownSequence(), SetPowerDownSequence() (needs power_down_order_reviewed), PowerDownDelayUs() | power-down order mirrors the power-up order after reset; the model runs the schedule | T03,T04: tests/test_configure.cpp; tests/test_model.cpp | OK |
| FLD-60.UNUSED | 0x60 SW2_PWRDN_SEQ[7:3] UNUSED (—, reset —) | Table 140 p101 | not exposed: reserved/unused; kept by read-modify-write, never forced | register file stores the bit | T03: tests/test_configure.cpp | INFO |
| FLD-61.SW3_PWRDN_SEQ | 0x61 SW3_PWRDN_SEQ[2:0] SW3_PWRDN_SEQ (RW1S, reset 000) | Table 141 p102 | ReadPowerDownSequence(), SetPowerDownSequence() (needs power_down_order_reviewed), PowerDownDelayUs() | power-down order mirrors the power-up order after reset; the model runs the schedule | T03,T04: tests/test_configure.cpp; tests/test_model.cpp | OK |
| FLD-61.UNUSED | 0x61 SW3_PWRDN_SEQ[7:3] UNUSED (—, reset —) | Table 141 p102 | not exposed: reserved/unused; kept by read-modify-write, never forced | register file stores the bit | T03: tests/test_configure.cpp | INFO |
| FLD-62.LDO1_PWRDN_SEQ | 0x62 LDO1_PWRDN_SEQ[2:0] LDO1_PWRDN_SEQ (RW1S, reset 000) | Table 142 p102 | ReadPowerDownSequence(), SetPowerDownSequence() (needs power_down_order_reviewed), PowerDownDelayUs() | power-down order mirrors the power-up order after reset; the model runs the schedule | T03,T04: tests/test_configure.cpp; tests/test_model.cpp | OK |
| FLD-62.UNUSED | 0x62 LDO1_PWRDN_SEQ[7:3] UNUSED (—, reset —) | Table 142 p102 | not exposed: reserved/unused; kept by read-modify-write, never forced | register file stores the bit | T03: tests/test_configure.cpp | INFO |
| FLD-63.LDO2_PWRDN_SEQ | 0x63 LDO2_PWRDN_SEQ[2:0] LDO2_PWRDN_SEQ (RW1S, reset 000) | Table 143 p103 | ReadPowerDownSequence(), SetPowerDownSequence() (needs power_down_order_reviewed), PowerDownDelayUs() | power-down order mirrors the power-up order after reset; the model runs the schedule | T03,T04: tests/test_configure.cpp; tests/test_model.cpp | OK |
| FLD-63.UNUSED | 0x63 LDO2_PWRDN_SEQ[7:3] UNUSED (—, reset —) | Table 143 p103 | not exposed: reserved/unused; kept by read-modify-write, never forced | register file stores the bit | T03: tests/test_configure.cpp | INFO |
| FLD-64.LDO3_PWRDN_SEQ | 0x64 LDO3_PWRDN_SEQ[2:0] LDO3_PWRDN_SEQ (RW1S, reset 000) | Table 144 p103 | ReadPowerDownSequence(), SetPowerDownSequence() (needs power_down_order_reviewed), PowerDownDelayUs() | power-down order mirrors the power-up order after reset; the model runs the schedule | T03,T04: tests/test_configure.cpp; tests/test_model.cpp | OK |
| FLD-64.UNUSED | 0x64 LDO3_PWRDN_SEQ[7:3] UNUSED (—, reset —) | Table 144 p103 | not exposed: reserved/unused; kept by read-modify-write, never forced | register file stores the bit | T03: tests/test_configure.cpp | INFO |
| FLD-65.VREFDDR_PWRDN_SEQ | 0x65 VREFDDR_PWRDN_SEQ[2:0] VREFDDR_PWRDN_SEQ (RW1S, reset 000) | Table 145 p104 | ReadPowerDownSequence(), SetPowerDownSequence() (needs power_down_order_reviewed), PowerDownDelayUs() | power-down order mirrors the power-up order after reset; the model runs the schedule | T03,T04: tests/test_configure.cpp; tests/test_model.cpp | OK |
| FLD-65.UNUSED | 0x65 VREFDDR_PWRDN_SEQ[7:3] UNUSED (—, reset —) | Table 145 p104 | not exposed: reserved/unused; kept by read-modify-write, never forced | register file stores the bit | T03: tests/test_configure.cpp | INFO |
| FLD-67.STATE | 0x67 STATE_INFO[5:0] STATE (R, reset 000000) | Table 146 p104 | ReadPowerState() -> PowerState | model state machine | T13: tests/test_power.cpp | OK |
| FLD-67.UNUSED | 0x67 STATE_INFO[7:6] UNUSED (—, reset —) | Table 146 p104 | not exposed: reserved/unused; kept by read-modify-write, never forced | register file stores the bit | T03: tests/test_configure.cpp | INFO |
| FLD-68.I2C_SLAVE_ADDR_LSBS | 0x68 I2C_ADDR[2:0] I2C_SLAVE_ADDR_LSBS (R, reset 000) | Table 147 p104 | VariantInfo.i2c_slave_addr_code (read only) | option 0x08..0x0F | T19: tests/test_lifecycle.cpp; tests/test_model.cpp | OK |
| FLD-68.USE_DEFAULT_ADDR | 0x68 I2C_ADDR[7] USE_DEFAULT_ADDR (RW, reset 0) | Table 147 p104 | not exposed: effect undefined (C23) | register file stores the bit; write attempts rejected by the access table | T04: tests/test_model.cpp; tests/test_configure.cpp | INFO |
| FLD-6B.REQ_16MHZ | 0x6B RC_16MHZ[0] REQ_16MHZ (RW, reset 0) | Table 148 p105 | not exposed: forces clocks/analog core on, current cost only (T148) | register file stores the bit; write attempts rejected by the access table | T04: tests/test_model.cpp; tests/test_configure.cpp | INFO |
| FLD-6B.REQ_ACORE_ON | 0x6B RC_16MHZ[1] REQ_ACORE_ON (RW, reset 0) | Table 148 p105 | not exposed: forces clocks/analog core on, current cost only (T148) | register file stores the bit; write attempts rejected by the access table | T04: tests/test_model.cpp; tests/test_configure.cpp | INFO |
| FLD-6B.REQ_ACORE_HIPWR | 0x6B RC_16MHZ[2] REQ_ACORE_HIPWR (RW, reset 0) | Table 148 p105 | not exposed: forces clocks/analog core on, current cost only (T148) | register file stores the bit; write attempts rejected by the access table | T04: tests/test_model.cpp; tests/test_configure.cpp | INFO |
| FLD-6B.UNUSED | 0x6B RC_16MHZ[7:3] UNUSED (—, reset —) | Table 148 p105 | not exposed: reserved/unused; kept by read-modify-write, never forced | register file stores the bit | T03: tests/test_configure.cpp | INFO |
| FLD-6F.KEY1 | 0x6F KEY1[7:0] KEY1 (RW, reset 0x00) | Table 149 p105 | not exposed: "Unused" (T149); OTP window undocumented (C5) | register file stores the bit; write attempts rejected by the access table | T04: tests/test_model.cpp; tests/test_configure.cpp | INFO |
| FLD-80.SUP_I | 0x80 CHG_INT[0] SUP_I (RW1S, reset 0) | Table 150 p105 | InterruptEvents.chg.sup | set on state change (Figure 16), clear per knob int_clear (C3) | T12,T07,T08: tests/test_irq.cpp; tests/test_charger.cpp | OK |
| FLD-80.BAT2SOC_I | 0x80 CHG_INT[1] BAT2SOC_I (RW1S, reset 0) | Table 150 p105 | Has(events, IrqSource::ChgBat2Soc).bat2soc | set on state change (Figure 16), clear per knob int_clear (C3) | T12,T07,T08: tests/test_irq.cpp; tests/test_charger.cpp | OK |
| FLD-80.BAT_I | 0x80 CHG_INT[2] BAT_I (RW1S, reset 0) | Table 150 p105 | Has(events, IrqSource::ChgBattery).bat | set on state change (Figure 16), clear per knob int_clear (C3) | T12,T07,T08: tests/test_irq.cpp; tests/test_charger.cpp | OK |
| FLD-80.CHG_I | 0x80 CHG_INT[3] CHG_I (RW1S, reset 0) | Table 150 p105 | Has(events, IrqSource::ChgCharger).chg | set on state change (Figure 16), clear per knob int_clear (C3) | T12,T07,T08: tests/test_irq.cpp; tests/test_charger.cpp | OK |
| FLD-80.RSVD4 | 0x80 CHG_INT[4] RSVD4 (RW1S, reset 0) | Table 150 p105 | not exposed: reserved/unused; kept by read-modify-write, never forced | register file stores the bit | T03: tests/test_configure.cpp | INFO |
| FLD-80.VBUS_I | 0x80 CHG_INT[5] VBUS_I (RW1S, reset 0) | Table 150 p105 | Has(events, IrqSource::ChgVbus).vbus | set on state change (Figure 16), clear per knob int_clear (C3) | T12,T07,T08: tests/test_irq.cpp; tests/test_charger.cpp | OK |
| FLD-80.VBUS_DPM_I | 0x80 CHG_INT[6] VBUS_DPM_I (RW1S, reset 0) | Table 150 p105 | Has(events, IrqSource::ChgVbusDpm) | set on state change (Figure 16), clear per knob int_clear (C3) | T12,T07,T08: tests/test_irq.cpp; tests/test_charger.cpp | OK |
| FLD-80.THM_I | 0x80 CHG_INT[7] THM_I (RW1S, reset 0) | Table 150 p105 | Has(events, IrqSource::ChgThermistor).thm | set on state change (Figure 16), clear per knob int_clear (C3) | T12,T07,T08: tests/test_irq.cpp; tests/test_charger.cpp | OK |
| FLD-82.SUP_M | 0x82 CHG_INT_MASK[0] SUP_M (RW, reset 1) | Table 151 p106 | IrqMask.chg.sup (1 = masked) | mask gates INTB only | T12: tests/test_irq.cpp | OK |
| FLD-82.BAT2SOC_M | 0x82 CHG_INT_MASK[1] BAT2SOC_M (RW, reset 1) | Table 151 p106 | UnmaskOnly({IrqSource::ChgBat2Soc}).bat2soc (1 = masked) | mask gates INTB only | T12: tests/test_irq.cpp | OK |
| FLD-82.BAT_M | 0x82 CHG_INT_MASK[2] BAT_M (RW, reset 1) | Table 151 p106 | UnmaskOnly({IrqSource::ChgBattery}).bat (1 = masked) | mask gates INTB only | T12: tests/test_irq.cpp | OK |
| FLD-82.CHG_M | 0x82 CHG_INT_MASK[3] CHG_M (RW, reset 1) | Table 151 p106 | UnmaskOnly({IrqSource::ChgCharger}).chg (1 = masked) | mask gates INTB only | T12: tests/test_irq.cpp | OK |
| FLD-82.RSVD4 | 0x82 CHG_INT_MASK[4] RSVD4 (RW, reset 1) | Table 151 p106 | not exposed: reserved/unused; kept by read-modify-write, never forced | register file stores the bit | T03: tests/test_configure.cpp | INFO |
| FLD-82.VBUS_M | 0x82 CHG_INT_MASK[5] VBUS_M (RW, reset 1) | Table 151 p106 | UnmaskOnly({IrqSource::ChgVbus}).vbus (1 = masked) | mask gates INTB only | T12: tests/test_irq.cpp | OK |
| FLD-82.VBUS_DPM_M | 0x82 CHG_INT_MASK[6] VBUS_DPM_M (RW, reset 1) | Table 151 p106 | UnmaskOnly({IrqSource::ChgVbusDpm}) (1 = masked) | mask gates INTB only | T12: tests/test_irq.cpp | OK |
| FLD-82.THM_M | 0x82 CHG_INT_MASK[7] THM_M (RW, reset 1) | Table 151 p106 | UnmaskOnly({IrqSource::ChgThermistor}).thm (1 = masked) | mask gates INTB only | T12: tests/test_irq.cpp | OK |
| FLD-84.SUP_OK | 0x84 CHG_INT_OK[0] SUP_OK (R, reset 0) | Table 152 p107 | Snapshot.sense[Charger].sup | derived from charger state machine | T07,T22: tests/test_charger.cpp; tests/test_irq.cpp | OK |
| FLD-84.BAT2SOC_OK | 0x84 CHG_INT_OK[1] BAT2SOC_OK (R, reset 0) | Table 152 p107 | Snapshot.sense[Charger].bat2soc | derived from charger state machine | T07,T22: tests/test_charger.cpp; tests/test_irq.cpp | OK |
| FLD-84.BAT_OK | 0x84 CHG_INT_OK[2] BAT_OK (R, reset 1) | Table 152 p107 | Snapshot.sense[Charger].bat | derived from charger state machine | T07,T22: tests/test_charger.cpp; tests/test_irq.cpp | OK |
| FLD-84.CHG_OK | 0x84 CHG_INT_OK[3] CHG_OK (R, reset 0) | Table 152 p107 | Snapshot.sense[Charger].chg | derived from charger state machine | T07,T22: tests/test_charger.cpp; tests/test_irq.cpp | OK |
| FLD-84.RSVD4 | 0x84 CHG_INT_OK[4] RSVD4 (R, reset 0) | Table 152 p107 | not exposed: reserved/unused; kept by read-modify-write, never forced | register file stores the bit | T03: tests/test_configure.cpp | INFO |
| FLD-84.VBUS_OK | 0x84 CHG_INT_OK[5] VBUS_OK (R, reset 0) | Table 152 p107 | Snapshot.sense[Charger].vbus | derived from charger state machine | T07,T22: tests/test_charger.cpp; tests/test_irq.cpp | OK |
| FLD-84.VBUS_DPM_OK | 0x84 CHG_INT_OK[6] VBUS_DPM_OK (R, reset 0) | Table 152 p107 | Snapshot.sense[Charger] bit VBUS_DPM_OK | derived from charger state machine | T07,T22: tests/test_charger.cpp; tests/test_irq.cpp | OK |
| FLD-84.THM_OK | 0x84 CHG_INT_OK[7] THM_OK (R, reset 1) | Table 152 p107 | Snapshot.sense[Charger].thm | derived from charger state machine | T07,T22: tests/test_charger.cpp; tests/test_irq.cpp | OK |
| FLD-86.RSVD0 | 0x86 VBUS_SNS[1:0] RSVD0 (R, reset 00) | Table 153 p107 | not exposed: reserved/unused; kept by read-modify-write, never forced | register file stores the bit | T03: tests/test_configure.cpp | INFO |
| FLD-86.VBUS_UVLO_SNS | 0x86 VBUS_SNS[2] VBUS_UVLO_SNS (R, reset 1) | Table 153 p107 | ChargerStatus.vbus.uvlo | VBUS voltage model | T11,T22: tests/test_charger.cpp; tests/test_irq.cpp | OK |
| FLD-86.VBUS_IN2SYS_SNS | 0x86 VBUS_SNS[3] VBUS_IN2SYS_SNS (R, reset 1) | Table 153 p107 | ChargerStatus.vbus.in2sys | VBUS voltage model | T11,T22: tests/test_charger.cpp; tests/test_irq.cpp | OK |
| FLD-86.VBUS_OVLO_SNS | 0x86 VBUS_SNS[4] VBUS_OVLO_SNS (R, reset 0) | Table 153 p107 | ChargerStatus.vbus.ovlo | VBUS voltage model | T11,T22: tests/test_charger.cpp; tests/test_irq.cpp | OK |
| FLD-86.VBUS_VALID | 0x86 VBUS_SNS[5] VBUS_VALID (R, reset 0) | Table 153 p107 | ChargerStatus.vbus.valid | VBUS voltage model | T11,T22: tests/test_charger.cpp; tests/test_irq.cpp | OK |
| FLD-86.RSVD6 | 0x86 VBUS_SNS[6] RSVD6 (R, reset 0) | Table 153 p107 | not exposed: reserved/unused; kept by read-modify-write, never forced | register file stores the bit | T03: tests/test_configure.cpp | INFO |
| FLD-86.VBUS_DPM_SNS | 0x86 VBUS_SNS[7] VBUS_DPM_SNS (R, reset 0) | Table 153 p107 | ChargerStatus.vbus.dpm | VBUS voltage model | T11,T22: tests/test_charger.cpp; tests/test_irq.cpp | OK |
| FLD-87.CHG_SNS | 0x87 CHG_SNS[3:0] CHG_SNS (R, reset 1000) | Table 154 p108 | ChargerStatus.state (enum ChargerState; reserved -> Unknown fault) | charger state machine | T07,T08,T22: tests/test_charger.cpp; tests/test_irq.cpp | OK |
| FLD-87.RSVD4 | 0x87 CHG_SNS[4] RSVD4 (R, reset 0) | Table 154 p108 | not exposed: reserved/unused; kept by read-modify-write, never forced | register file stores the bit | T03: tests/test_configure.cpp | INFO |
| FLD-87.WDT_SNS | 0x87 CHG_SNS[5] WDT_SNS (R, reset 0) | Table 154 p108 | ChargerStatus.watchdog_expired (C9) | watchdog expiry | T08,T09: tests/test_charger.cpp | OK |
| FLD-87.THM_SNS | 0x87 CHG_SNS[6] THM_SNS (R, reset 0) | Table 154 p108 | ChargerStatus.thermistor_outside | thermistor window | T10: tests/test_configure.cpp; tests/test_charger.cpp | OK |
| FLD-87.TREG_SNS | 0x87 CHG_SNS[7] TREG_SNS (R, reset 0) | Table 154 p108 | ChargerStatus.thermal_regulation | foldback active | T10: tests/test_configure.cpp; tests/test_charger.cpp | OK |
| FLD-88.BATT_SNS | 0x88 BATT_SNS[2:0] BATT_SNS (R, reset 000) | Table 155 p109 | ChargerStatus.battery (enum BatteryState; reserved -> Unknown) | battery model | T08,T22: tests/test_charger.cpp; tests/test_irq.cpp | OK |
| FLD-88.RSVD3 | 0x88 BATT_SNS[4:3] RSVD3 (RW, reset 00) | Table 155 p109 | not exposed: reserved/unused; kept by read-modify-write, never forced | register file stores the bit | T03: tests/test_configure.cpp | INFO |
| FLD-88.BATTOC_SNS | 0x88 BATT_SNS[5] BATTOC_SNS (R, reset 0) | Table 155 p109 | ChargerStatus.battery_overcurrent | overcurrent latch | T08: tests/test_charger.cpp | OK |
| FLD-88.RSVD6 | 0x88 BATT_SNS[7:6] RSVD6 (RW, reset 00) | Table 155 p109 | not exposed: reserved/unused; kept by read-modify-write, never forced | register file stores the bit | T03: tests/test_configure.cpp | INFO |
| FLD-89.CHG_OPER | 0x89 CHG_OPER[1:0] CHG_OPER (RW1S, reset 01) | Table 156 p109 | ChargerConfig.mode, written last | off/linear/charge | T06,T07: tests/test_configure.cpp; tests/test_charger.cpp | OK |
| FLD-89.UNUSED | 0x89 CHG_OPER[2] UNUSED (RW, reset 0) | Table 156 p109 | not exposed: reserved/unused; kept by read-modify-write, never forced | register file stores the bit | T03: tests/test_configure.cpp | INFO |
| FLD-89.WDTEN | 0x89 CHG_OPER[3] WDTEN (RW, reset 0) | Table 156 p109 | ChargerConfig.watchdog.enable; needs ServiceChargerWatchdog every <= 16 s | watchdog timer | T09,T08: tests/test_charger.cpp | OK |
| FLD-89.DISBATFET | 0x89 CHG_OPER[4] DISBATFET (RW, reset 0) | Table 156 p109 | ChargerConfig.batfet.disable, ack allow_batfet_off | BATFET forced off | T08,T05: tests/test_charger.cpp; tests/test_config.cpp | OK |
| FLD-89.UNUSED[7:5] | 0x89 CHG_OPER[7:5] UNUSED (RW, reset 000) | Table 156 p109 | not exposed: reserved/unused; kept by read-modify-write, never forced | register file stores the bit | T03: tests/test_configure.cpp | INFO |
| FLD-8A.FCHGTIME | 0x8A CHG_TMR[2:0] FCHGTIME (RW1S, reset 010) | Table 157 p110 | ChargerConfig.fast_timer; Disabled needs ack allow_untimed_charge | tFC | T09,T05: tests/test_charger.cpp; tests/test_config.cpp | OK |
| FLD-8A.EOCTIME | 0x8A CHG_TMR[5:3] EOCTIME (RW1S, reset 001) | Table 157 p110 | ChargerConfig.eoc_timer | tEOC | T09: tests/test_charger.cpp | OK |
| FLD-8A.RSVD6 | 0x8A CHG_TMR[6] RSVD6 (R, reset 0) | Table 157 p110 | not exposed: reserved/unused; kept by read-modify-write, never forced | register file stores the bit | T03: tests/test_configure.cpp | INFO |
| FLD-8A.TPRECHG | 0x8A CHG_TMR[7] TPRECHG (RW1S, reset 0) | Table 157 p110 | ChargerConfig.precharge_timer | tPRECHG | T09: tests/test_charger.cpp | OK |
| FLD-8D.CHG_RESTART | 0x8D CHG_EOC_CNFG[1:0] CHG_RESTART (RW1S, reset 01) | Table 158 p111 | ChargerConfig.restart | restart threshold | T07: tests/test_charger.cpp | OK |
| FLD-8D.FORCE_BATT_ISO | 0x8D CHG_EOC_CNFG[2] FORCE_BATT_ISO (RW1S, reset 0) | Table 158 p111 | not exposed: "Unused" (T158) | register file stores the bit; write attempts rejected by the access table | T04: tests/test_model.cpp; tests/test_configure.cpp | INFO |
| FLD-8D.EOC_EXIT | 0x8D CHG_EOC_CNFG[3] EOC_EXIT (RW1S, reset 0) | Table 158 p111 | not exposed: "Unused" (T158) | register file stores the bit; write attempts rejected by the access table | T04: tests/test_model.cpp; tests/test_configure.cpp | INFO |
| FLD-8D.IEOC | 0x8D CHG_EOC_CNFG[6:4] IEOC (RW, reset 100) | Table 158 p111 | ChargerConfig.termination_ma {5,10,20,30,50}; 5/10 need ack eoc_accuracy_accepted | EOC detect with accuracy band | T01,T07,T05: tests/test_config.cpp; inc/pf1550_codec.hpp (static_assert); tests/test_charger.cpp | OK |
| FLD-8D.EOC_MODE | 0x8D CHG_EOC_CNFG[7] EOC_MODE (RW1S, reset 0) | Table 158 p111 | not exposed: "Unused" in T158 but an option in T85 (C25) | register file stores the bit; write attempts rejected by the access table | T04: tests/test_model.cpp; tests/test_configure.cpp | INFO |
| FLD-8E.CHG_CC | 0x8E CHG_CURR_CNFG[4:0] CHG_CC (RW1S, reset 00000) | Table 159 p112 | ChargerConfig.charge_current_ma <= Limits.cell_max_charge_ma; reserved codes unencodable | AppliedCcMa() | T01,T02,T07: tests/test_config.cpp; inc/pf1550_codec.hpp (static_assert); tests/test_review.cpp; tests/test_charger.cpp | OK |
| FLD-8E.PRECHGLB_THRS | 0x8E CHG_CURR_CNFG[6:5] PRECHGLB_THRS (RW1S, reset 00) | Table 159 p112 | Configure() writes code 0 (2.8 V) only; other codes Reserved (C17) | PRECHGLB_THRS code 0 (2.8 V) stored | T01,T02: tests/test_config.cpp; inc/pf1550_codec.hpp (static_assert); tests/test_review.cpp | OK |
| FLD-8E.RSVD7 | 0x8E CHG_CURR_CNFG[7] RSVD7 (RW, reset 0) | Table 159 p112 | not exposed: reserved/unused; kept by read-modify-write, never forced | register file stores the bit | T03: tests/test_configure.cpp | INFO |
| FLD-8F.CHGCV | 0x8F BATT_REG[5:0] CHGCV (RW1S, reset 101011) | Table 160 p113 | ChargerConfig.charge_voltage_mv <= Limits.cell_max_mv; codes 8..55 only | AppliedCvMv() | T01,T02,T07: tests/test_config.cpp; inc/pf1550_codec.hpp (static_assert); tests/test_review.cpp; tests/test_charger.cpp | OK |
| FLD-8F.VSYSMIN | 0x8F BATT_REG[7:6] VSYSMIN (RW1S, reset 00) | Table 160 p113 | ChargerConfig.vsys_min | VSYS minimum | T01,T07: tests/test_config.cpp; inc/pf1550_codec.hpp (static_assert); tests/test_charger.cpp | OK |
| FLD-91.WDTCLR | 0x91 BATFET_CNFG[1:0] WDTCLR (RW, reset 00) | Table 161 p114 | ServiceChargerWatchdog() writes 01 | clears and restarts | T09,T08: tests/test_charger.cpp | OK |
| FLD-91.WD_BATFET_OFF | 0x91 BATFET_CNFG[2] WD_BATFET_OFF (RW, reset 0) | Table 161 p114 | not exposed: "not used in PF1550" | register file stores the bit; write attempts rejected by the access table | T04: tests/test_model.cpp; tests/test_configure.cpp | INFO |
| FLD-91.BOVRC_DISBATFET | 0x91 BATFET_CNFG[3] BOVRC_DISBATFET (RW1S, reset 0) | Table 161 p114 | ChargerConfig.batfet.oc_keeps_closed, ack (C18) | BATFET on OC | T08,T05: tests/test_charger.cpp; tests/test_config.cpp | OK |
| FLD-91.BATFET_OC | 0x91 BATFET_CNFG[5:4] BATFET_OC (RW1S, reset 11) | Table 161 p114 | ChargerConfig.batfet.oc_threshold {Disabled, 2.2, 2.8, 3.2 A}; Disabled needs ack | OC threshold, 16 ms | T08,T05: tests/test_charger.cpp; tests/test_config.cpp | OK |
| FLD-91.WD_TIME | 0x91 BATFET_CNFG[6] WD_TIME (RW, reset 0) | Table 161 p114 | ChargerConfig.watchdog.time (C8) | knob wd_time_one_is_32s | T09: tests/test_charger.cpp | OK |
| FLD-91.BOVRC_NOVBUS | 0x91 BATFET_CNFG[7] BOVRC_NOVBUS (RW, reset 0) | Table 161 p114 | ChargerConfig.batfet.oc_without_vbus | OC without VBUS | T08: tests/test_charger.cpp | OK |
| FLD-92.THM_CNFG | 0x92 THM_REG_CNFG[1:0] THM_CNFG (RW1S, reset 01) | Table 162 p115 | ChargerConfig.thermistor {Suspend, Jeita1, Jeita2, Ignore}; Ignore needs ack battery_has_own_ntc_protection | thermistor modes | T10,T05: tests/test_configure.cpp; tests/test_charger.cpp; tests/test_config.cpp | OK |
| FLD-92.REGTEMP | 0x92 THM_REG_CNFG[3:2] REGTEMP (RW1S, reset 01) | Table 162 p115 | ChargerConfig.thermal_reg.temperature {80, 95, 110 C}; code 3 reserved (C46) | foldback threshold | T01,T10: tests/test_config.cpp; inc/pf1550_codec.hpp (static_assert); tests/test_configure.cpp; tests/test_charger.cpp | OK |
| FLD-92.THM_COLD | 0x92 THM_REG_CNFG[4] THM_COLD (RW1S, reset 0) | Table 162 p115 | ChargerConfig.jeita.cold | cold threshold | T10: tests/test_configure.cpp; tests/test_charger.cpp | OK |
| FLD-92.THM_HOT | 0x92 THM_REG_CNFG[5] THM_HOT (RW1S, reset 0) | Table 162 p115 | ChargerConfig.jeita.hot | hot threshold | T10: tests/test_configure.cpp; tests/test_charger.cpp | OK |
| FLD-92.RSVD6 | 0x92 THM_REG_CNFG[6] RSVD6 (RW, reset 0) | Table 162 p115 | not exposed: reserved/unused; kept by read-modify-write, never forced | register file stores the bit | T03: tests/test_configure.cpp | INFO |
| FLD-92.TEMP_FB_EN | 0x92 THM_REG_CNFG[7] TEMP_FB_EN (RW1S, reset 0) | Table 162 p115 | ChargerConfig.thermal_reg.foldback (reset 0 = off; Config default on, m4) | foldback enable | T10: tests/test_configure.cpp; tests/test_charger.cpp | OK |
| FLD-94.RSVD0 | 0x94 VBUS_INLIM_CNFG[2:0] RSVD0 (RW, reset 000) | Table 163 p116 | not exposed: reserved/unused; kept by read-modify-write, never forced | register file stores the bit | T03: tests/test_configure.cpp | INFO |
| FLD-94.VBUS_LIN_ILIM | 0x94 VBUS_INLIM_CNFG[7:3] VBUS_LIN_ILIM (RW1S, reset 01101) | Table 163 p116 | ChargerConfig.input_limit_ma (21 codes) <= Limits.input_max_ma | applied input limit; VbusRemoved() restores the OTP value | T01,T02,T11,T05: tests/test_config.cpp; inc/pf1550_codec.hpp (static_assert); tests/test_review.cpp; tests/test_charger.cpp; tests/test_round3.cpp | OK |
| FLD-95.VBUS_DPM_REG | 0x95 VBUS_LIN_DPM[2:0] VBUS_DPM_REG (RW1S, reset 000) | Table 164 p117 | ChargerConfig.vbus.dpm 3.9..4.6 V (reset 3.9 V, C24) | DPM loop | T01,T11: tests/test_config.cpp; inc/pf1550_codec.hpp (static_assert); tests/test_charger.cpp | OK |
| FLD-95.PRECHGDBATT_THRSH | 0x95 VBUS_LIN_DPM[4:3] PRECHGDBATT_THRSH (RW1S, reset 00) | Table 164 p117 | not exposed: all codes Reserved | register file stores the bit; write attempts rejected by the access table | T04: tests/test_model.cpp; tests/test_configure.cpp | INFO |
| FLD-95.VIN_DPM_STOP | 0x95 VBUS_LIN_DPM[5] VIN_DPM_STOP (RW1S, reset 0) | Table 164 p117 | ChargerConfig.vbus.dpm_stop | DPM stop flag | T11: tests/test_charger.cpp | OK |
| FLD-95.RSVD6 | 0x95 VBUS_LIN_DPM[6] RSVD6 (R, reset 0) | Table 164 p117 | not exposed: reserved/unused; kept by read-modify-write, never forced | register file stores the bit | T03: tests/test_configure.cpp | INFO |
| FLD-95.FET_SCALE | 0x95 VBUS_LIN_DPM[7] FET_SCALE (RW1S, reset 0) | Table 164 p117 | not exposed: all codes Reserved | register file stores the bit; write attempts rejected by the access table | T04: tests/test_model.cpp; tests/test_configure.cpp | INFO |
| FLD-96.ACTDISPHY | 0x96 USB_PHY_LDO_CNFG[0] ACTDISPHY (RW1S, reset 1) | Table 165 p117 | UsbPhyConfig.active_discharge | flag state | T18: tests/test_power.cpp; tests/test_configure.cpp | OK |
| FLD-96.USBPHY | 0x96 USB_PHY_LDO_CNFG[1] USBPHY (RW1S, reset 0) | Table 165 p117 | UsbPhyConfig.voltage | UsbphyMv() | T18: tests/test_power.cpp; tests/test_configure.cpp | OK |
| FLD-96.USBPHYLDO | 0x96 USB_PHY_LDO_CNFG[2] USBPHYLDO (RW1S, reset 0) | Table 165 p117 | UsbPhyConfig.enable | UsbphyEnabled() | T18: tests/test_power.cpp; tests/test_configure.cpp | OK |
| FLD-96.RSVD3 | 0x96 USB_PHY_LDO_CNFG[3] RSVD3 (RW, reset 0) | Table 165 p117 | not exposed: reserved/unused; kept by read-modify-write, never forced | register file stores the bit | T03: tests/test_configure.cpp | INFO |
| FLD-96.RSVD4 | 0x96 USB_PHY_LDO_CNFG[5:4] RSVD4 (RW, reset 00) | Table 165 p117 | not exposed: reserved/unused; kept by read-modify-write, never forced | register file stores the bit | T03: tests/test_configure.cpp | INFO |
| FLD-96.RSVD6 | 0x96 USB_PHY_LDO_CNFG[7:6] RSVD6 (RW, reset 00) | Table 165 p117 | not exposed: reserved/unused; kept by read-modify-write, never forced | register file stores the bit | T03: tests/test_configure.cpp | INFO |
| FLD-98.VBUS_OV_TDB | 0x98 DBNC_DELAY_TIME[1:0] VBUS_OV_TDB (RW1S, reset 00) | Table 166 p118 | ChargerConfig.vbus.ovlo_debounce | OVLO debounce | T11,T20: tests/test_charger.cpp; tests/test_configure.cpp | OK |
| FLD-98.USB_PHY_TDB | 0x98 DBNC_DELAY_TIME[3:2] USB_PHY_TDB (RW1S, reset 00) | Table 166 p118 | not exposed: "not used in PF1550" | register file stores the bit; write attempts rejected by the access table | T04: tests/test_model.cpp; tests/test_configure.cpp | INFO |
| FLD-98.SYS_WKUP_DLY | 0x98 DBNC_DELAY_TIME[5:4] SYS_WKUP_DLY (RW1S, reset 00) | Table 166 p118 | ChargerConfig.vbus.sys_wakeup_delay | wake-up delay | T11,T20: tests/test_charger.cpp; tests/test_configure.cpp | OK |
| FLD-98.RSVD6 | 0x98 DBNC_DELAY_TIME[7:6] RSVD6 (RW, reset 00) | Table 166 p118 | not exposed: reserved/unused; kept by read-modify-write, never forced | register file stores the bit | T03: tests/test_configure.cpp | INFO |
| FLD-99.CHG_INT_GEN | 0x99 CHG_INT_CNFG[0] CHG_INT_GEN (RW1S, reset 0) | Table 167 p118 | ChargerConfig.interrupts.every_transition | interrupt on every transition | T12: tests/test_irq.cpp | OK |
| FLD-99.EOC_INT | 0x99 CHG_INT_CNFG[1] EOC_INT (RW1S, reset 0) | Table 167 p118 | ChargerConfig.interrupts.eoc | EOC interrupt | T12: tests/test_irq.cpp | OK |
| FLD-99.RSVD2 | 0x99 CHG_INT_CNFG[7:2] RSVD2 (RW, reset 000000) | Table 167 p118 | not exposed: reserved/unused; kept by read-modify-write, never forced | register file stores the bit | T03: tests/test_configure.cpp | INFO |
| FLD-9A.THM_WARM | 0x9A THM_ADJ_SETTING[0] THM_WARM (RW1S, reset 0) | Table 168 p118 | ChargerConfig.jeita.warm | warm threshold | T10: tests/test_configure.cpp; tests/test_charger.cpp | OK |
| FLD-9A.THM_COOL | 0x9A THM_ADJ_SETTING[1] THM_COOL (RW1S, reset 0) | Table 168 p118 | ChargerConfig.jeita.cool | cool threshold | T10: tests/test_configure.cpp; tests/test_charger.cpp | OK |
| FLD-9A.CV_ADJ | 0x9A THM_ADJ_SETTING[3:2] CV_ADJ (RW1S, reset 00) | Table 168 p118 | ChargerConfig.jeita.cv_adjust | CV reduction (T67) | T10: tests/test_configure.cpp; tests/test_charger.cpp | OK |
| FLD-9A.CC_ADJ | 0x9A THM_ADJ_SETTING[5:4] CC_ADJ (RW1S, reset 00) | Table 168 p118 | ChargerConfig.jeita.cc_adjust | CC reduction (T68) | T10: tests/test_configure.cpp; tests/test_charger.cpp | OK |
| FLD-9A.RSVD6 | 0x9A THM_ADJ_SETTING[7:6] RSVD6 (RW, reset 00) | Table 168 p118 | not exposed: reserved/unused; kept by read-modify-write, never forced | register file stores the bit | T03: tests/test_configure.cpp | INFO |
| FLD-9B.VBUS2SYS_TDB | 0x9B VBUS2SYS_CNFG[1:0] VBUS2SYS_TDB (RW1S, reset 00) | Table 169 p119 | ChargerConfig.vbus.vbus2sys_debounce | comparator debounce | T11,T20: tests/test_charger.cpp; tests/test_configure.cpp | OK |
| FLD-9B.VBUS2SYS_THRSH | 0x9B VBUS2SYS_CNFG[2] VBUS2SYS_THRSH (RW1S, reset 0) | Table 169 p119 | ChargerConfig.vbus.vbus2sys_threshold | VBUS-VSYS threshold | T11: tests/test_charger.cpp | OK |
| FLD-9B.RSVD3 | 0x9B VBUS2SYS_CNFG[7:3] RSVD3 (RW, reset 00000) | Table 169 p119 | not exposed: reserved/unused; kept by read-modify-write, never forced | register file stores the bit | T03: tests/test_configure.cpp | INFO |
| FLD-9C.LED_PWM | 0x9C LED_PWM[5:0] LED_PWM (RW, reset 000000) | Table 170 p120 | LedConfig.duty_32nds 0..32 (C43) | led duty | T17: tests/test_configure.cpp | OK |
| FLD-9C.LED_RAMP | 0x9C LED_PWM[6] LED_RAMP (RW, reset 0) | Table 170 p120 | LedConfig.ramp | ramp flag | T17: tests/test_configure.cpp | OK |
| FLD-9C.LED_EN | 0x9C LED_PWM[7] LED_EN (RW, reset 0) | Table 170 p120 | LedConfig.enable | Led() | T17: tests/test_configure.cpp | OK |
| FLD-9D.OVFLT_BFET_EN | 0x9D FAULT_BATFET_CNFG[0] OVFLT_BFET_EN (RW1S, reset 0) | Table 171 p120 | ChargerConfig.batfet.fault_policy.on_overvoltage; keep-closed needs ack | BATFET per fault (T171) | T08,T05: tests/test_charger.cpp; tests/test_config.cpp | OK |
| FLD-9D.WDFLT_BFET_EN | 0x9D FAULT_BATFET_CNFG[1] WDFLT_BFET_EN (RW1S, reset 0) | Table 171 p120 | ChargerConfig.batfet.fault_policy.on_watchdog; keep-closed needs ack | BATFET per fault (T171) | T08,T05: tests/test_charger.cpp; tests/test_config.cpp | OK |
| FLD-9D.THMSUS_BFET_EN | 0x9D FAULT_BATFET_CNFG[2] THMSUS_BFET_EN (RW1S, reset 0) | Table 171 p120 | ChargerConfig.batfet.fault_policy.on_thermistor; keep-closed needs ack | BATFET per fault (T171) | T08,T05: tests/test_charger.cpp; tests/test_config.cpp | OK |
| FLD-9D.TSHDN_BFET_EN | 0x9D FAULT_BATFET_CNFG[3] TSHDN_BFET_EN (RW1S, reset 0) | Table 171 p120 | ChargerConfig.batfet.fault_policy.on_thermal_shutdown; keep-closed needs ack | BATFET per fault (T171) | T08,T05: tests/test_charger.cpp; tests/test_config.cpp | OK |
| FLD-9D.TMRFLT_BFET_EN | 0x9D FAULT_BATFET_CNFG[4] TMRFLT_BFET_EN (RW1S, reset 0) | Table 171 p120 | ChargerConfig.batfet.fault_policy.on_timer_fault; keep-closed needs ack | BATFET per fault (T171) | T08,T05: tests/test_charger.cpp; tests/test_config.cpp | OK |
| FLD-9D.RSVD5 | 0x9D FAULT_BATFET_CNFG[5] RSVD5 (RW1S, reset 0) | Table 171 p120 | not exposed: reserved/unused; kept by read-modify-write, never forced | register file stores the bit | T03: tests/test_configure.cpp | INFO |
| FLD-9D.CTRL_CHGR_BETA_SEL | 0x9D FAULT_BATFET_CNFG[7:6] CTRL_CHGR_BETA_SEL (RW1S, reset 00) | Table 171 p120 | not exposed: Reserved (T176 names OTP_CHGR_BETA_SEL) | register file stores the bit; write attempts rejected by the access table | T04: tests/test_model.cpp; tests/test_configure.cpp | INFO |
| FLD-9E.LED_FREQ | 0x9E LED_CNFG[1:0] LED_FREQ (RW, reset 00) | Table 172 p121 | LedConfig.frequency | blink period | T17: tests/test_configure.cpp | OK |
| FLD-9E.LED_CURRENT | 0x9E LED_CNFG[3:2] LED_CURRENT (RW1S, reset 00) | Table 172 p121 | Configure() writes 01 (6 mA) when LedConfig used; other codes Reserved (C44) | led current code | T17: tests/test_configure.cpp | OK |
| FLD-9E.LED_CFG | 0x9E LED_CNFG[4] LED_CFG (RW1S, reset 0) | Table 172 p121 | LedConfig.mode | Led() | T17: tests/test_configure.cpp | OK |
| FLD-9E.LEDOVRD | 0x9E LED_CNFG[5] LEDOVRD (RW, reset 0) | Table 172 p121 | LedConfig.software_override | Led() | T17: tests/test_configure.cpp | OK |
| FLD-9E.RSVD4 | 0x9E LED_CNFG[7:6] RSVD4 (RW, reset 00) | Table 172 p121 | not exposed: reserved/unused; kept by read-modify-write, never forced | register file stores the bit | T03: tests/test_configure.cpp | INFO |
| FLD-9F.CHGR_KEY2 | 0x9F CHGR_KEY2[7:0] CHGR_KEY2 (RW, reset 0x00) | Table 173 p122 | not exposed: Reserved (T173); key sequence undocumented (C5) | register file stores the bit; write attempts rejected by the access table | T04: tests/test_model.cpp; tests/test_configure.cpp | INFO |
| FLD-69.IO_DRV0_BITS | 0x69 IO_DRV0[7:0] IO_DRV0_BITS (RW, reset bitmap) | Table 174 p125 | not exposed: bitmap only, no field text (C47) | register file stores the bit; write attempts rejected by the access table | T04: tests/test_model.cpp; tests/test_configure.cpp | INFO |
| FLD-6A.IO_DRV1_BITS | 0x6A IO_DRV1[7:0] IO_DRV1_BITS (RW, reset bitmap) | Table 174 p125 | not exposed: bitmap only, no field text (C47) | register file stores the bit; write attempts rejected by the access table | T04: tests/test_model.cpp; tests/test_configure.cpp | INFO |
| FLD-68.GAP_6_3 | 0x68 I2C_ADDR[6:3] GAP_6_3 (-, reset no row in T147 (table gap)) | Table 147 p104 | not exposed: no row in T147 (table gap); preserved | register file stores the bit; write attempts rejected by the access table | T04: tests/test_model.cpp; tests/test_configure.cpp | INFO |
Interrupt sources¶
| Id | Item | Datasheet | API | Model | Test | Status |
|---|---|---|---|---|---|---|
| INT-08.SW1_LS_I | SW1_LS_I (SW_INT_STAT0 b0); mask and sense counterparts in the next registers | Table 90 p82 | Has(events, IrqSource::Sw1LowSideLimit); IrqMask; Snapshot.sense | set on event, mask gates INTB, clear per int_clear | T12,T15: tests/test_irq.cpp; tests/test_rails.cpp | OK |
| INT-08.SW2_LS_I | SW2_LS_I (SW_INT_STAT0 b1); mask and sense counterparts in the next registers | Table 90 p82 | Has(events, IrqSource::Sw2LowSideLimit); IrqMask; Snapshot.sense | set on event, mask gates INTB, clear per int_clear | T12,T15: tests/test_irq.cpp; tests/test_rails.cpp | OK |
| INT-08.SW3_LS_I | SW3_LS_I (SW_INT_STAT0 b2); mask and sense counterparts in the next registers | Table 90 p82 | Has(events, IrqSource::Sw3LowSideLimit); IrqMask; Snapshot.sense | set on event, mask gates INTB, clear per int_clear | T12,T15: tests/test_irq.cpp; tests/test_rails.cpp | OK |
| INT-0B.SW1_HS_I | SW1_HS_I (SW_INT_STAT1 b0); mask and sense counterparts in the next registers | Table 93 p83 | Has(events, IrqSource::Sw1HighSideLimit); IrqMask; Snapshot.sense | set on event, mask gates INTB, clear per int_clear | T12,T15: tests/test_irq.cpp; tests/test_rails.cpp | OK |
| INT-0B.SW2_HS_I | SW2_HS_I (SW_INT_STAT1 b1); mask and sense counterparts in the next registers | Table 93 p83 | Has(events, IrqSource::Sw2HighSideLimit); IrqMask; Snapshot.sense | set on event, mask gates INTB, clear per int_clear | T12,T15: tests/test_irq.cpp; tests/test_rails.cpp | OK |
| INT-0B.SW3_HS_I | SW3_HS_I (SW_INT_STAT1 b2); mask and sense counterparts in the next registers | Table 93 p83 | Has(events, IrqSource::Sw3HighSideLimit); IrqMask; Snapshot.sense | set on event, mask gates INTB, clear per int_clear | T12,T15: tests/test_irq.cpp; tests/test_rails.cpp | OK |
| INT-0E.SW1_DVS_DONE_I | SW1_DVS_DONE_I (SW_INT_STAT2 b0); mask and sense counterparts in the next registers | Table 96 p84 | Has(events, IrqSource::Sw1DvsDone); IrqMask; Snapshot.sense | set on event, mask gates INTB, clear per int_clear | T12,T14: tests/test_irq.cpp; tests/test_rails.cpp; tests/test_configure.cpp | OK |
| INT-0E.SW2_DVS_DONE_I | SW2_DVS_DONE_I (SW_INT_STAT2 b1); mask and sense counterparts in the next registers | Table 96 p84 | Has(events, IrqSource::Sw2DvsDone); IrqMask; Snapshot.sense | set on event, mask gates INTB, clear per int_clear | T12,T14: tests/test_irq.cpp; tests/test_rails.cpp; tests/test_configure.cpp | OK |
| INT-18.LDO1_FAULTI | LDO1_FAULTI (LDO_INT_STAT0 b0); mask and sense counterparts in the next registers | Table 99 p85 | Has(events, IrqSource::Ldo1Fault); IrqMask; Snapshot.sense | set on event, mask gates INTB, clear per int_clear | T12,T15: tests/test_irq.cpp; tests/test_rails.cpp | OK |
| INT-18.LDO2_FAULTI | LDO2_FAULTI (LDO_INT_STAT0 b1); mask and sense counterparts in the next registers | Table 99 p85 | Has(events, IrqSource::Ldo2Fault); IrqMask; Snapshot.sense | set on event, mask gates INTB, clear per int_clear | T12,T15: tests/test_irq.cpp; tests/test_rails.cpp | OK |
| INT-18.LDO3_FAULTI | LDO3_FAULTI (LDO_INT_STAT0 b2); mask and sense counterparts in the next registers | Table 99 p85 | Has(events, IrqSource::Ldo3Fault); IrqMask; Snapshot.sense | set on event, mask gates INTB, clear per int_clear | T12,T15: tests/test_irq.cpp; tests/test_rails.cpp | OK |
| INT-20.THERM110I | THERM110I (TEMP_INT_STAT0 b0); mask and sense counterparts in the next registers | Table 102 p86 | Has(events, IrqSource::Temp110); IrqMask; Snapshot.sense | set on event, mask gates INTB, clear per int_clear | T12,T10: tests/test_irq.cpp; tests/test_configure.cpp; tests/test_charger.cpp | OK |
| INT-20.THERM125I | THERM125I (TEMP_INT_STAT0 b2); mask and sense counterparts in the next registers | Table 102 p86 | Has(events, IrqSource::Temp125); IrqMask; Snapshot.sense | set on event, mask gates INTB, clear per int_clear | T12,T10: tests/test_irq.cpp; tests/test_configure.cpp; tests/test_charger.cpp | OK |
| INT-24.ONKEY_PUSHI | ONKEY_PUSHI (ONKEY_INT_STAT0 b0); mask and sense counterparts in the next registers | Table 105 p87 | Has(events, IrqSource::OnkeyPush); IrqMask; Snapshot.sense | set on event, mask gates INTB, clear per int_clear | T12,T13: tests/test_irq.cpp; tests/test_power.cpp | OK |
| INT-24.ONKEY_1SI | ONKEY_1SI (ONKEY_INT_STAT0 b1); mask and sense counterparts in the next registers | Table 105 p87 | Has(events, IrqSource::Onkey1s); IrqMask; Snapshot.sense | set on event, mask gates INTB, clear per int_clear | T12,T13: tests/test_irq.cpp; tests/test_power.cpp | OK |
| INT-24.ONKEY_2SI | ONKEY_2SI (ONKEY_INT_STAT0 b2); mask and sense counterparts in the next registers | Table 105 p87 | Has(events, IrqSource::Onkey2s); IrqMask; Snapshot.sense | set on event, mask gates INTB, clear per int_clear | T12,T13: tests/test_irq.cpp; tests/test_power.cpp | OK |
| INT-24.ONKEY_3SI | ONKEY_3SI (ONKEY_INT_STAT0 b3); mask and sense counterparts in the next registers | Table 105 p87 | Has(events, IrqSource::Onkey3s); IrqMask; Snapshot.sense | set on event, mask gates INTB, clear per int_clear | T12,T13: tests/test_irq.cpp; tests/test_power.cpp | OK |
| INT-24.ONKEY_4SI | ONKEY_4SI (ONKEY_INT_STAT0 b4); mask and sense counterparts in the next registers | Table 105 p87 | Has(events, IrqSource::Onkey4s); IrqMask; Snapshot.sense | set on event, mask gates INTB, clear per int_clear | T12,T13: tests/test_irq.cpp; tests/test_power.cpp | OK |
| INT-24.ONKEY_8SI | ONKEY_8SI (ONKEY_INT_STAT0 b5); mask and sense counterparts in the next registers | Table 105 p87 | Has(events, IrqSource::Onkey8s); IrqMask; Snapshot.sense | set on event, mask gates INTB, clear per int_clear | T12,T13: tests/test_irq.cpp; tests/test_power.cpp | OK |
| INT-28.PWRUP_I | PWRUP_I (MISC_INT_STAT0 b0); mask and sense counterparts in the next registers | Table 108 p89 | Has(events, IrqSource::PowerUp); IrqMask; Snapshot.sense | set on event, mask gates INTB, clear per int_clear | T12,T13: tests/test_irq.cpp; tests/test_power.cpp | OK |
| INT-28.PWRDN_I | PWRDN_I (MISC_INT_STAT0 b1); mask and sense counterparts in the next registers | Table 108 p89 | Has(events, IrqSource::PowerDown); IrqMask; Snapshot.sense | set on event, mask gates INTB, clear per int_clear | T12,T13: tests/test_irq.cpp; tests/test_power.cpp | OK |
| INT-28.PWRON_I | PWRON_I (MISC_INT_STAT0 b2); mask and sense counterparts in the next registers | Table 108 p89 | Has(events, IrqSource::PwronChange); IrqMask; Snapshot.sense | set on event, mask gates INTB, clear per int_clear | T12,T13: tests/test_irq.cpp; tests/test_power.cpp | OK |
| INT-28.LOW_SYS_WARN_I | LOW_SYS_WARN_I (MISC_INT_STAT0 b3); mask and sense counterparts in the next registers | Table 108 p89 | Has(events, IrqSource::LowSysWarning); IrqMask; Snapshot.sense | set on event, mask gates INTB, clear per int_clear | T12,T13: tests/test_irq.cpp; tests/test_power.cpp | OK |
| INT-28.SYS_OVLO_I | SYS_OVLO_I (MISC_INT_STAT0 b4); mask and sense counterparts in the next registers | Table 108 p89 | Has(events, IrqSource::SysOvervoltage); IrqMask; Snapshot.sense | set on event, mask gates INTB, clear per int_clear | T12,T13: tests/test_irq.cpp; tests/test_power.cpp | OK |
| INT-80.SUP_I | SUP_I (CHG_INT b0); mask and sense counterparts in the next registers | Table 150 p105 | InterruptEvents.sup; IrqMask; Snapshot.sense | set on event, mask gates INTB, clear per int_clear | T12,T07,T08: tests/test_irq.cpp; tests/test_charger.cpp | OK |
| INT-80.BAT2SOC_I | BAT2SOC_I (CHG_INT b1); mask and sense counterparts in the next registers | Table 150 p105 | Has(events, IrqSource::ChgBat2Soc); IrqMask; Snapshot.sense | set on event, mask gates INTB, clear per int_clear | T12,T07,T08: tests/test_irq.cpp; tests/test_charger.cpp | OK |
| INT-80.BAT_I | BAT_I (CHG_INT b2); mask and sense counterparts in the next registers | Table 150 p105 | Has(events, IrqSource::ChgBattery); IrqMask; Snapshot.sense | set on event, mask gates INTB, clear per int_clear | T12,T07,T08: tests/test_irq.cpp; tests/test_charger.cpp | OK |
| INT-80.CHG_I | CHG_I (CHG_INT b3); mask and sense counterparts in the next registers | Table 150 p105 | Has(events, IrqSource::ChgCharger); IrqMask; Snapshot.sense | set on event, mask gates INTB, clear per int_clear | T12,T07,T08: tests/test_irq.cpp; tests/test_charger.cpp | OK |
| INT-80.VBUS_I | VBUS_I (CHG_INT b5); mask and sense counterparts in the next registers | Table 150 p105 | Has(events, IrqSource::ChgVbus); IrqMask; Snapshot.sense | set on event, mask gates INTB, clear per int_clear | T12,T07,T08: tests/test_irq.cpp; tests/test_charger.cpp | OK |
| INT-80.VBUS_DPM_I | VBUS_DPM_I (CHG_INT b6); mask and sense counterparts in the next registers | Table 150 p105 | Has(events, IrqSource::ChgVbusDpm); IrqMask; Snapshot.sense | set on event, mask gates INTB, clear per int_clear | T12,T07,T08: tests/test_irq.cpp; tests/test_charger.cpp | OK |
| INT-80.THM_I | THM_I (CHG_INT b7); mask and sense counterparts in the next registers | Table 150 p105 | Has(events, IrqSource::ChgThermistor); IrqMask; Snapshot.sense | set on event, mask gates INTB, clear per int_clear | T12,T07,T08: tests/test_irq.cpp; tests/test_charger.cpp | OK |
PMIC and charger states, transitions, status codes¶
| Id | Item | Datasheet | API | Model | Test | Status |
|---|---|---|---|---|---|---|
| PMS-WAIT | PMIC state WAIT (STATE_INFO 000000) | Table 146 p104 | ReadPowerState() decodes STATE_INFO; other codes -> Unknown | model state machine | T13: tests/test_power.cpp | OK |
| PMS-RUN | PMIC state RUN (STATE_INFO 001100) | Table 83 p76 | ReadPowerState() decodes STATE_INFO; other codes -> Unknown | model state machine | T13: tests/test_power.cpp | OK |
| PMS-STANDBY | PMIC state STANDBY (STATE_INFO 001101) | 10.2.2 | ReadPowerState() decodes STATE_INFO; other codes -> Unknown | model state machine | T13: tests/test_power.cpp | OK |
| PMS-SLEEP/LPSR | PMIC state SLEEP/LPSR (STATE_INFO 001110) | 10.2 | ReadPowerState() decodes STATE_INFO; other codes -> Unknown | model state machine | T13: tests/test_power.cpp | OK |
| PMS-REGS_DISABLE | PMIC state REGS_DISABLE (STATE_INFO 101011; home state) | Table 83 | ReadPowerState() decodes STATE_INFO; other codes -> Unknown | model state machine | T13: tests/test_power.cpp | OK |
| PMS-CORE_OFF | PMIC state CORE_OFF (no STATE_INFO code (system off, no I2C) (C36)) | Table 83 | not readable; EnterShip/EnterCoreOff reach it | model state machine | T16: tests/test_power.cpp; tests/test_rails.cpp; tests/test_review.cpp | OK |
| PMS-SHIP | PMIC state SHIP (no STATE_INFO code (no I2C) (C36)) | Table 83 | not readable; EnterShip/EnterCoreOff reach it | model state machine | T16: tests/test_power.cpp; tests/test_rails.cpp; tests/test_review.cpp | OK |
| PMT-A | Transition A: STANDBY to RUN (pin, STANDBYINV) | Table 83 p76-77 | observed via ReadPowerState and MISC interrupts; not commanded | model implements both PWRON_CFG columns | T13: tests/test_power.cpp | OK |
| PMT-B | Transition B: RUN to STANDBY (pin, STANDBYINV) | Table 83 p76-77 | observed via ReadPowerState and MISC interrupts; not commanded | model implements both PWRON_CFG columns | T13: tests/test_power.cpp | OK |
| PMT-C | Transition C: STANDBY to SLEEP (PWRON, OMODE) | Table 83 p76-77 | observed via ReadPowerState and MISC interrupts; not commanded | model implements both PWRON_CFG columns | T13: tests/test_power.cpp | OK |
| PMT-E | Transition E: SLEEP to RUN (PWRON) | Table 83 p76-77 | observed via ReadPowerState and MISC interrupts; not commanded | model implements both PWRON_CFG columns | T13: tests/test_power.cpp | OK |
| PMT-F | Transition F: RUN to SLEEP (PWRON, OMODE) | Table 83 p76-77 | observed via ReadPowerState and MISC interrupts; not commanded | model implements both PWRON_CFG columns | T13: tests/test_power.cpp | OK |
| PMT-G | Transition G: RUN/STANDBY/SLEEP to REGS_DISABLE (thermal, GOTO_SHIP, PWRON, WDI, ONKEY, UVDET) | Table 83 p76-77 | EnterShip (G+J) / EnterCoreOff (I); K, L only observed by the next ReadPowerState | model implements both PWRON_CFG columns | T16: tests/test_power.cpp; tests/test_rails.cpp; tests/test_review.cpp | OK |
| PMT-H | Transition H: REGS_DISABLE to RUN (PWRON, RESTARTEN, charger attach; VSYS>UVDET, TJ<TSHDN_fall) | Table 83 p76-77 | observed via ReadPowerState and MISC interrupts; not commanded | model implements both PWRON_CFG columns | T13: tests/test_power.cpp | OK |
| PMT-I | Transition I: REGS_DISABLE to CORE_OFF (GOTO_CORE_OFF, ONKEY; VBUS invalid) | Table 83 p76-77 | EnterShip (G+J) / EnterCoreOff (I); K, L only observed by the next ReadPowerState | model implements both PWRON_CFG columns | T16: tests/test_power.cpp; tests/test_rails.cpp; tests/test_review.cpp | OK |
| PMT-J | Transition J: REGS_DISABLE to SHIP (GOTO_SHIP, VBUS<1 V) | Table 83 p76-77 | EnterShip (G+J) / EnterCoreOff (I); K, L only observed by the next ReadPowerState | model implements both PWRON_CFG columns | T16: tests/test_power.cpp; tests/test_rails.cpp; tests/test_review.cpp | OK |
| PMT-K | Transition K: CORE_OFF to REGS_DISABLE (ONKEY >1 s, charger attach) | Table 83 p76-77 | EnterShip (G+J) / EnterCoreOff (I); K, L only observed by the next ReadPowerState | model implements both PWRON_CFG columns | T16: tests/test_power.cpp; tests/test_rails.cpp; tests/test_review.cpp | OK |
| PMT-L | Transition L: SHIP to REGS_DISABLE (charger attach, battery reattach) | Table 83 p76-77 | EnterShip (G+J) / EnterCoreOff (I); K, L only observed by the next ReadPowerState | model implements both PWRON_CFG columns | T16: tests/test_power.cpp; tests/test_rails.cpp; tests/test_review.cpp | OK |
| CHS-0 | CHG_SNS = 0: precharge | Table 154 p108 | ChargerStatus.state decoded to enum ChargerState | charger state machine (Figure 16) | T07,T08: tests/test_charger.cpp | OK |
| CHS-1 | CHG_SNS = 1: CC | Table 154 p108 | ChargerStatus.state decoded to enum ChargerState | charger state machine (Figure 16) | T07,T08: tests/test_charger.cpp | OK |
| CHS-2 | CHG_SNS = 2: CV | Table 154 p108 | ChargerStatus.state decoded to enum ChargerState | charger state machine (Figure 16) | T07,T08: tests/test_charger.cpp | OK |
| CHS-3 | CHG_SNS = 3: EOC | Table 154 p108 | ChargerStatus.state decoded to enum ChargerState | charger state machine (Figure 16) | T07,T08: tests/test_charger.cpp | OK |
| CHS-4 | CHG_SNS = 4: Done | Table 154 p108 | ChargerStatus.state decoded to enum ChargerState | charger state machine (Figure 16) | T07,T08: tests/test_charger.cpp | OK |
| CHS-5 | CHG_SNS = 5: Reserved | Table 154 p108 | ChargerStatus.state: reserved -> Unknown, treated as fault, never "charging" | model never produces it; a foreign write may force | T08,T22: tests/test_charger.cpp; tests/test_irq.cpp | OK |
| CHS-6 | CHG_SNS = 6: timer fault | Table 154 p108 | ChargerStatus.state decoded to enum ChargerState | charger state machine (Figure 16) | T07,T08: tests/test_charger.cpp | OK |
| CHS-7 | CHG_SNS = 7: thermistor suspend | Table 154 p108 | ChargerStatus.state decoded to enum ChargerState | charger state machine (Figure 16) | T07,T08: tests/test_charger.cpp | OK |
| CHS-8 | CHG_SNS = 8: off / input invalid | Table 154 p108 | ChargerStatus.state decoded to enum ChargerState | charger state machine (Figure 16) | T07,T08: tests/test_charger.cpp | OK |
| CHS-9 | CHG_SNS = 9: battery overvoltage | Table 154 p108 | ChargerStatus.state decoded to enum ChargerState | charger state machine (Figure 16) | T07,T08: tests/test_charger.cpp | OK |
| CHS-10 | CHG_SNS = 10: off, TJ>TSHDN | Table 154 p108 | ChargerStatus.state decoded to enum ChargerState | charger state machine (Figure 16) | T07,T08: tests/test_charger.cpp | OK |
| CHS-11 | CHG_SNS = 11: Reserved | Table 154 p108 | ChargerStatus.state: reserved -> Unknown, treated as fault, never "charging" | model never produces it; a foreign write may force | T08,T22: tests/test_charger.cpp; tests/test_irq.cpp | OK |
| CHS-12 | CHG_SNS = 12: linear only | Table 154 p108 | ChargerStatus.state decoded to enum ChargerState | charger state machine (Figure 16) | T07,T08: tests/test_charger.cpp | OK |
| CHS-13 | CHG_SNS = 13: Reserved | Table 154 p108 | ChargerStatus.state: reserved -> Unknown, treated as fault, never "charging" | model never produces it; a foreign write may force | T08,T22: tests/test_charger.cpp; tests/test_irq.cpp | OK |
| CHS-14 | CHG_SNS = 14: Reserved | Table 154 p108 | ChargerStatus.state: reserved -> Unknown, treated as fault, never "charging" | model never produces it; a foreign write may force | T08,T22: tests/test_charger.cpp; tests/test_irq.cpp | OK |
| CHS-15 | CHG_SNS = 15: Reserved | Table 154 p108 | ChargerStatus.state: reserved -> Unknown, treated as fault, never "charging" | model never produces it; a foreign write may force | T08,T22: tests/test_charger.cpp; tests/test_irq.cpp | OK |
| BAS-0 | BATT_SNS = 0: no valid VBUS | Table 155 p109 | ChargerStatus.battery decoded; reserved -> Unknown | battery model | T08,T22: tests/test_charger.cpp; tests/test_irq.cpp | OK |
| BAS-1 | BATT_SNS = 1: VBATT < VPRECHG.LB | Table 155 p109 | ChargerStatus.battery decoded; reserved -> Unknown | battery model | T08,T22: tests/test_charger.cpp; tests/test_irq.cpp | OK |
| BAS-2 | BATT_SNS = 2: cannot charge beyond threshold (timer fault) | Table 155 p109 | ChargerStatus.battery decoded; reserved -> Unknown | battery model | T08,T22: tests/test_charger.cpp; tests/test_irq.cpp | OK |
| BAS-3 | BATT_SNS = 3: Reserved | Table 155 p109 | ChargerStatus.battery decoded; reserved -> Unknown | battery model | T08,T22: tests/test_charger.cpp; tests/test_irq.cpp | OK |
| BAS-4 | BATT_SNS = 4: VBATT > VPRECHG.LB | Table 155 p109 | ChargerStatus.battery decoded; reserved -> Unknown | battery model | T08,T22: tests/test_charger.cpp; tests/test_irq.cpp | OK |
| BAS-5 | BATT_SNS = 5: battery overvoltage | Table 155 p109 | ChargerStatus.battery decoded; reserved -> Unknown | battery model | T08,T22: tests/test_charger.cpp; tests/test_irq.cpp | OK |
| BAS-6 | BATT_SNS = 6: battery not detected | Table 155 p109 | ChargerStatus.battery decoded; reserved -> Unknown | battery model | T08,T22: tests/test_charger.cpp; tests/test_irq.cpp | OK |
| BAS-7 | BATT_SNS = 7: Reserved | Table 155 p109 | ChargerStatus.battery decoded; reserved -> Unknown | battery model | T08,T22: tests/test_charger.cpp; tests/test_irq.cpp | OK |
Electrical characteristics and ratings (T3 to T26, per parameter)¶
| Id | Item | Datasheet | API | Model | Test | Status |
|---|---|---|---|---|---|---|
| EL-T3-TA | TA: Ambient operating temperature range (industrial) | Table 3 p9 | not applicable: rating or thermal figure; no register, the driver cannot influence it (hardware page) | not modelled | N/A: no driver decision | INFO |
| EL-T3-TJ | TJ: Operating junction temperature range | Table 3 p9 | not applicable: rating or thermal figure; no register, the driver cannot influence it (hardware page) | not modelled | N/A: no driver decision | INFO |
| EL-T3-TST | TST: Storage temperature range | Table 3 p9 | not applicable: rating or thermal figure; no register, the driver cannot influence it (hardware page) | not modelled | N/A: no driver decision | INFO |
| EL-T3-TPPRT | TPPRT: Peak package reflow temperature | Table 3 p9 | not applicable: rating or thermal figure; no register, the driver cannot influence it (hardware page) | not modelled | N/A: no driver decision | INFO |
| EL-T3-RJA | RΘJA: Junction to ambient thermal resistance, natural convection | Table 3 p9 | not applicable: rating or thermal figure; no register, the driver cannot influence it (hardware page) | not modelled | N/A: no driver decision | INFO |
| EL-T3-RJMA | RΘJMA: Junction to ambient (at 200 ft/min) | Table 3 p9 | not applicable: rating or thermal figure; no register, the driver cannot influence it (hardware page) | not modelled | N/A: no driver decision | INFO |
| EL-T3-RJB | RΘJB: Junction to board | Table 3 p9 | not applicable: rating or thermal figure; no register, the driver cannot influence it (hardware page) | not modelled | N/A: no driver decision | INFO |
| EL-T3-JT | ΨJT: Junction to package top – Natural convection | Table 3 p9 | not applicable: rating or thermal figure; no register, the driver cannot influence it (hardware page) | not modelled | N/A: no driver decision | INFO |
| EL-T4-VDDIO | VDDIO: I/O supply voltage. Connect to voltage rail between 1.7 V an | Table 4 p10 | not applicable: absolute maximum rating; documented on the hardware page, enforced by board design | not modelled | N/A: no driver decision | INFO |
| EL-T4-SCL | SCL: SCL when used in I C mode. SCLK when used in SPI mode. | Table 4 p10 | not applicable: absolute maximum rating; documented on the hardware page, enforced by board design | not modelled | N/A: no driver decision | INFO |
| EL-T4-SDA | SDA: SDA when used in I C mode. MISO when used in SPI mode. | Table 4 p10 | not applicable: absolute maximum rating; documented on the hardware page, enforced by board design | not modelled | N/A: no driver decision | INFO |
| EL-T4-RESETBMCU | RESETBMCU: RESETBMCU open-drain output | Table 4 p10 | not applicable: absolute maximum rating; documented on the hardware page, enforced by board design | not modelled | N/A: no driver decision | INFO |
| EL-T4-PWRON | PWRON: PWRON input | Table 4 p10 | not applicable: absolute maximum rating; documented on the hardware page, enforced by board design | not modelled | N/A: no driver decision | INFO |
| EL-T4-STANDBY | STANDBY: STANDBY input | Table 4 p10 | not applicable: absolute maximum rating; documented on the hardware page, enforced by board design | not modelled | N/A: no driver decision | INFO |
| EL-T4-ONKEY | ONKEY: ONKEY push-button input | Table 4 p10 | not applicable: absolute maximum rating; documented on the hardware page, enforced by board design | not modelled | N/A: no driver decision | INFO |
| EL-T4-INTB | INTB: INTB open-drain output | Table 4 p10 | not applicable: absolute maximum rating; documented on the hardware page, enforced by board design | not modelled | N/A: no driver decision | INFO |
| EL-T4-WDI | WDI: Watchdog input from processor | Table 4 p10 | not applicable: absolute maximum rating; documented on the hardware page, enforced by board design | not modelled | N/A: no driver decision | INFO |
| EL-T4-VDDOTP | VDDOTP: Connect to ground in the application | Table 4 p10 | not applicable: absolute maximum rating; documented on the hardware page, enforced by board design | not modelled | N/A: no driver decision | INFO |
| EL-T4-SW1IN | SW1IN: Buck 1 input supply | Table 4 p10 | not applicable: absolute maximum rating; documented on the hardware page, enforced by board design | not modelled | N/A: no driver decision | INFO |
| EL-T4-SW1LX | SW1LX: Buck 1 switching node | Table 4 p10 | not applicable: absolute maximum rating; documented on the hardware page, enforced by board design | not modelled | N/A: no driver decision | INFO |
| EL-T4-SW1FB | SW1FB: Buck 1 feedback input | Table 4 p10 | not applicable: absolute maximum rating; documented on the hardware page, enforced by board design | not modelled | N/A: no driver decision | INFO |
| EL-T4-SW2IN | SW2IN: Buck 2 input supply | Table 4 p10 | not applicable: absolute maximum rating; documented on the hardware page, enforced by board design | not modelled | N/A: no driver decision | INFO |
| EL-T4-SW2LX | SW2LX: Buck 2 switching node | Table 4 p10 | not applicable: absolute maximum rating; documented on the hardware page, enforced by board design | not modelled | N/A: no driver decision | INFO |
| EL-T4-SW2FB | SW2FB: Buck 2 output voltage feedback | Table 4 p10 | not applicable: absolute maximum rating; documented on the hardware page, enforced by board design | not modelled | N/A: no driver decision | INFO |
| EL-T4-SW3IN | SW3IN: Buck 3 input supply | Table 4 p10 | not applicable: absolute maximum rating; documented on the hardware page, enforced by board design | not modelled | N/A: no driver decision | INFO |
| EL-T4-SW3LX | SW3LX: Buck 3 switching node | Table 4 p10 | not applicable: absolute maximum rating; documented on the hardware page, enforced by board design | not modelled | N/A: no driver decision | INFO |
| EL-T4-SW3FB | SW3FB: Buck 3 output voltage feedback | Table 4 p10 | not applicable: absolute maximum rating; documented on the hardware page, enforced by board design | not modelled | N/A: no driver decision | INFO |
| EL-T4-VLDO1IN | VLDO1IN: LDO1 input supply | Table 4 p10 | not applicable: absolute maximum rating; documented on the hardware page, enforced by board design | not modelled | N/A: no driver decision | INFO |
| EL-T4-VLDO1 | VLDO1: LDO1 output | Table 4 p10 | not applicable: absolute maximum rating; documented on the hardware page, enforced by board design | not modelled | N/A: no driver decision | INFO |
| EL-T4-VLDO2IN | VLDO2IN: LDO2 input supply | Table 4 p10 | not applicable: absolute maximum rating; documented on the hardware page, enforced by board design | not modelled | N/A: no driver decision | INFO |
| EL-T4-VLDO2 | VLDO2: LDO2 output | Table 4 p10 | not applicable: absolute maximum rating; documented on the hardware page, enforced by board design | not modelled | N/A: no driver decision | INFO |
| EL-T4-VLDO3IN | VLDO3IN: LDO3 input supply | Table 4 p10 | not applicable: absolute maximum rating; documented on the hardware page, enforced by board design | not modelled | N/A: no driver decision | INFO |
| EL-T4-VLDO3 | VLDO3: LDO3 output | Table 4 p10 | not applicable: absolute maximum rating; documented on the hardware page, enforced by board design | not modelled | N/A: no driver decision | INFO |
| EL-T4-VSNVS | VSNVS: VSNVS regulator output | Table 4 p10 | not applicable: absolute maximum rating; documented on the hardware page, enforced by board design | not modelled | N/A: no driver decision | INFO |
| EL-T4-LICELL | LICELL: Coin cell input | Table 4 p10 | not applicable: absolute maximum rating; documented on the hardware page, enforced by board design | not modelled | N/A: no driver decision | INFO |
| EL-T4-VBATT | VBATT: Battery input | Table 4 p10 | not applicable: absolute maximum rating; documented on the hardware page, enforced by board design | not modelled | N/A: no driver decision | INFO |
| EL-T4-INT2P7 | INT2P7: INT2P7 regulator output (used within PF1550 and as thermisto | Table 4 p10 | not applicable: absolute maximum rating; documented on the hardware page, enforced by board design | not modelled | N/A: no driver decision | INFO |
| EL-T4-THM | THM: Thermistor connection. Connect thermistor to ground from thi | Table 4 p10 | not applicable: absolute maximum rating; documented on the hardware page, enforced by board design | not modelled | N/A: no driver decision | INFO |
| EL-T4-VBUSIN | VBUSIN: Charger input | Table 4 p10 | not applicable: absolute maximum rating; documented on the hardware page, enforced by board design | not modelled | N/A: no driver decision | INFO |
| EL-T4-USBPHY | USBPHY: USBPHY regulator output | Table 4 p10 | not applicable: absolute maximum rating; documented on the hardware page, enforced by board design | not modelled | N/A: no driver decision | INFO |
| EL-T4-CHGB | CHGB: Charger LED input connection. Connect LED from VSYS to this | Table 4 p10 | not applicable: absolute maximum rating; documented on the hardware page, enforced by board design | not modelled | N/A: no driver decision | INFO |
| EL-T4-VINREFDDR | VINREFDDR: VREFDDR input supply | Table 4 p10 | not applicable: absolute maximum rating; documented on the hardware page, enforced by board design | not modelled | N/A: no driver decision | INFO |
| EL-T4-VREFDDR | VREFDDR: VREFDDR output | Table 4 p10 | not applicable: absolute maximum rating; documented on the hardware page, enforced by board design | not modelled | N/A: no driver decision | INFO |
| EL-T4-VSYS | VSYS: Main input voltage to PMIC and output of charger | Table 4 p10 | not applicable: absolute maximum rating; documented on the hardware page, enforced by board design | not modelled | N/A: no driver decision | INFO |
| EL-T4-VDIG | VDIG: VCOREDIG regulator output (used within PF1550) | Table 4 p10 | not applicable: absolute maximum rating; documented on the hardware page, enforced by board design | not modelled | N/A: no driver decision | INFO |
| EL-T4-VCORE | VCORE: VCORE regulator output (used within PF1550) | Table 4 p10 | not applicable: absolute maximum rating; documented on the hardware page, enforced by board design | not modelled | N/A: no driver decision | INFO |
| EL-T4-VESD | VESD: Human body model | Table 4 p11 | not applicable: absolute maximum rating; documented on the hardware page, enforced by board design | not modelled | N/A: no driver decision | INFO |
| EL-T5-VBUS | VBUS: VBUSIN voltage range Operating voltage | Table 5 p12 | VBUS_SNS flags reported; thresholds not configurable (docs) | VBUS comparator threshold, hysteresis, delay | T11,T27: tests/test_charger.cpp; tests/test_config.cpp; tests/test_model.cpp | OK |
| EL-T5-VBUS_WITHSTAND | VBUS_WITHSTAND: VBUSIN maximum withstand | Table 5 p12 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T5-VBUS_OVLO | VBUS_OVLO: VBUSIN overvoltage threshold Rising | Table 5 p12 | VBUS_SNS flags reported; thresholds not configurable (docs) | VBUS comparator threshold, hysteresis, delay | T11,T27: tests/test_charger.cpp; tests/test_config.cpp; tests/test_model.cpp | OK |
| EL-T5-VOVLO_HYS | VOVLO_HYS: VBUSIN overvoltage threshold Falling | Table 5 p12 | VBUS_SNS flags reported; thresholds not configurable (docs) | VBUS comparator threshold, hysteresis, delay | T11,T27: tests/test_charger.cpp; tests/test_config.cpp; tests/test_model.cpp | OK |
| EL-T5-tD-OVLO | tD-OVLO: VBUSIN overvoltage delay | Table 5 p12 | VBUS_SNS flags reported; thresholds not configurable (docs) | VBUS comparator threshold, hysteresis, delay | T11,T27: tests/test_charger.cpp; tests/test_config.cpp; tests/test_model.cpp | OK |
| EL-T5-VUVLO | VUVLO: VBUSIN to GND minimum turn VBUS rising | Table 5 p12 | VBUS_SNS flags reported; thresholds not configurable (docs) | VBUS comparator threshold, hysteresis, delay | T11,T27: tests/test_charger.cpp; tests/test_config.cpp; tests/test_model.cpp | OK |
| EL-T5-VUVLO-HYS | VUVLO-HYS: VBUSIN UVLO hysteresis | Table 5 p12 | VBUS_SNS flags reported; thresholds not configurable (docs) | VBUS comparator threshold, hysteresis, delay | T11,T27: tests/test_charger.cpp; tests/test_config.cpp; tests/test_model.cpp | OK |
| EL-T5-VIN2SYS_50 | VIN2SYS_50: VBUSIN to VSYS minimum turn VBUS_LIN rising, 50 mV setting 2 | Table 5 p12 | VBUS_SNS flags reported; thresholds not configurable (docs) | VBUS comparator threshold, hysteresis, delay | T11,T27: tests/test_charger.cpp; tests/test_config.cpp; tests/test_model.cpp | OK |
| EL-T5-VIN2SYS_175 | VIN2SYS_175: VBUSIN to VSYS minimum turn VBUS_LIN rising, 175 mV | Table 5 p12 | VBUS_SNS flags reported; thresholds not configurable (docs) | VBUS comparator threshold, hysteresis, delay | T11,T27: tests/test_charger.cpp; tests/test_config.cpp; tests/test_model.cpp | OK |
| EL-T5-VBUS_LIN_DPM_REG | VBUS_LIN_DPM_REG: VBUSIN adaptive voltage 4.4 V setting (defaul | Table 5 p12 | VBUS_SNS flags reported; thresholds not configurable (docs) | VBUS comparator threshold, hysteresis, delay | T11,T27: tests/test_charger.cpp; tests/test_config.cpp; tests/test_model.cpp | OK |
| EL-T5-VDPM_REG | VDPM_REG: VBUSIN adaptive voltage Programmable at 3.9 V | Table 5 p12 | VBUS_SNS flags reported; thresholds not configurable (docs) | VBUS comparator threshold, hysteresis, delay | T11,T27: tests/test_charger.cpp; tests/test_config.cpp; tests/test_model.cpp | OK |
| EL-T6-ILIM10 | ILIM10: Charger input current limit (10 10 mA | Table 6 p12 | ChargerConfig.input_limit_ma accepts only documented codes, <= Limits.input_max_ma | applied input limit | T01,T02,T27: tests/test_config.cpp; inc/pf1550_codec.hpp (static_assert); tests/test_review.cpp; tests/test_model.cpp | OK |
| EL-T6-ILIM15 | ILIM15: Charger input current limit (15 15 mA | Table 6 p12 | ChargerConfig.input_limit_ma accepts only documented codes, <= Limits.input_max_ma | applied input limit | T01,T02,T27: tests/test_config.cpp; inc/pf1550_codec.hpp (static_assert); tests/test_review.cpp; tests/test_model.cpp | OK |
| EL-T6-ILIM20 | ILIM20: Charger input current limit (20 20 mA | Table 6 p12 | ChargerConfig.input_limit_ma accepts only documented codes, <= Limits.input_max_ma | applied input limit | T01,T02,T27: tests/test_config.cpp; inc/pf1550_codec.hpp (static_assert); tests/test_review.cpp; tests/test_model.cpp | OK |
| EL-T6-ILIM25 | ILIM25: Charger input current limit (25 25 mA | Table 6 p12 | ChargerConfig.input_limit_ma accepts only documented codes, <= Limits.input_max_ma | applied input limit | T01,T02,T27: tests/test_config.cpp; inc/pf1550_codec.hpp (static_assert); tests/test_review.cpp; tests/test_model.cpp | OK |
| EL-T6-ILIM30 | ILIM30: Charger Input Current Limit (30 30 mA | Table 6 p12 | ChargerConfig.input_limit_ma accepts only documented codes, <= Limits.input_max_ma | applied input limit | T01,T02,T27: tests/test_config.cpp; inc/pf1550_codec.hpp (static_assert); tests/test_review.cpp; tests/test_model.cpp | OK |
| EL-T6-ILIM35 | ILIM35: Charger input current limit (35 35 mA | Table 6 p12 | ChargerConfig.input_limit_ma accepts only documented codes, <= Limits.input_max_ma | applied input limit | T01,T02,T27: tests/test_config.cpp; inc/pf1550_codec.hpp (static_assert); tests/test_review.cpp; tests/test_model.cpp | OK |
| EL-T6-ILIM40 | ILIM40: Charger input current limit (40 40 mA | Table 6 p12 | ChargerConfig.input_limit_ma accepts only documented codes, <= Limits.input_max_ma | applied input limit | T01,T02,T27: tests/test_config.cpp; inc/pf1550_codec.hpp (static_assert); tests/test_review.cpp; tests/test_model.cpp | OK |
| EL-T6-ILIM45 | ILIM45: Charger input current limit (45 45 mA | Table 6 p12 | ChargerConfig.input_limit_ma accepts only documented codes, <= Limits.input_max_ma | applied input limit | T01,T02,T27: tests/test_config.cpp; inc/pf1550_codec.hpp (static_assert); tests/test_review.cpp; tests/test_model.cpp | OK |
| EL-T6-ILIM50 | ILIM50: Charger input current limit (50 50 mA | Table 6 p12 | ChargerConfig.input_limit_ma accepts only documented codes, <= Limits.input_max_ma | applied input limit | T01,T02,T27: tests/test_config.cpp; inc/pf1550_codec.hpp (static_assert); tests/test_review.cpp; tests/test_model.cpp | OK |
| EL-T6-ILIM100 | ILIM100: Charger input current limit (100 100 mA | Table 6 p12 | ChargerConfig.input_limit_ma accepts only documented codes, <= Limits.input_max_ma | applied input limit | T01,T02,T27: tests/test_config.cpp; inc/pf1550_codec.hpp (static_assert); tests/test_review.cpp; tests/test_model.cpp | OK |
| EL-T6-ILIM150 | ILIM150: Charger input current limit (150 150 mA | Table 6 p12 | ChargerConfig.input_limit_ma accepts only documented codes, <= Limits.input_max_ma | applied input limit | T01,T02,T27: tests/test_config.cpp; inc/pf1550_codec.hpp (static_assert); tests/test_review.cpp; tests/test_model.cpp | OK |
| EL-T6-ILIM200 | ILIM200: Charger input current limit (200 200 mA | Table 6 p12 | ChargerConfig.input_limit_ma accepts only documented codes, <= Limits.input_max_ma | applied input limit | T01,T02,T27: tests/test_config.cpp; inc/pf1550_codec.hpp (static_assert); tests/test_review.cpp; tests/test_model.cpp | OK |
| EL-T6-ILIM300 | ILIM300: Charger input current limit (300 300 mA | Table 6 p12 | ChargerConfig.input_limit_ma accepts only documented codes, <= Limits.input_max_ma | applied input limit | T01,T02,T27: tests/test_config.cpp; inc/pf1550_codec.hpp (static_assert); tests/test_review.cpp; tests/test_model.cpp | OK |
| EL-T6-ILIM400 | ILIM400: Charger input current limit (400 400 mA | Table 6 p12 | ChargerConfig.input_limit_ma accepts only documented codes, <= Limits.input_max_ma | applied input limit | T01,T02,T27: tests/test_config.cpp; inc/pf1550_codec.hpp (static_assert); tests/test_review.cpp; tests/test_model.cpp | OK |
| EL-T6-ILIM500 | ILIM500: Charger input current limit (500 500 mA | Table 6 p12 | ChargerConfig.input_limit_ma accepts only documented codes, <= Limits.input_max_ma | applied input limit | T01,T02,T27: tests/test_config.cpp; inc/pf1550_codec.hpp (static_assert); tests/test_review.cpp; tests/test_model.cpp | OK |
| EL-T6-ILIM600 | ILIM600: Charger input current limit (600 600 mA | Table 6 p12 | ChargerConfig.input_limit_ma accepts only documented codes, <= Limits.input_max_ma | applied input limit | T01,T02,T27: tests/test_config.cpp; inc/pf1550_codec.hpp (static_assert); tests/test_review.cpp; tests/test_model.cpp | OK |
| EL-T6-ILIM700 | ILIM700: Charger input current limit (700 700 mA | Table 6 p12 | ChargerConfig.input_limit_ma accepts only documented codes, <= Limits.input_max_ma | applied input limit | T01,T02,T27: tests/test_config.cpp; inc/pf1550_codec.hpp (static_assert); tests/test_review.cpp; tests/test_model.cpp | OK |
| EL-T6-ILIM800 | ILIM800: Charger input current limit (800 800 mA | Table 6 p12 | ChargerConfig.input_limit_ma accepts only documented codes, <= Limits.input_max_ma | applied input limit | T01,T02,T27: tests/test_config.cpp; inc/pf1550_codec.hpp (static_assert); tests/test_review.cpp; tests/test_model.cpp | OK |
| EL-T6-ILIM900 | ILIM900: Charger input current limit (900 900 mA | Table 6 p12 | ChargerConfig.input_limit_ma accepts only documented codes, <= Limits.input_max_ma | applied input limit | T01,T02,T27: tests/test_config.cpp; inc/pf1550_codec.hpp (static_assert); tests/test_review.cpp; tests/test_model.cpp | OK |
| EL-T6-ILIM1000 | ILIM1000: Charger input current limit (1000 1000 mA | Table 6 p12 | ChargerConfig.input_limit_ma accepts only documented codes, <= Limits.input_max_ma | applied input limit | T01,T02,T27: tests/test_config.cpp; inc/pf1550_codec.hpp (static_assert); tests/test_review.cpp; tests/test_model.cpp | OK |
| EL-T6-ILIM1500 | ILIM1500: Charger input current limit (1500 1500 mA | Table 6 p12 | ChargerConfig.input_limit_ma accepts only documented codes, <= Limits.input_max_ma | applied input limit | T01,T02,T27: tests/test_config.cpp; inc/pf1550_codec.hpp (static_assert); tests/test_review.cpp; tests/test_model.cpp | OK |
| EL-T6-RINSD | RINSD: Input self-discharge resistance | Table 6 p12 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T6-IBATTLEAK | IBATTLEAK: Leakage current Leakage current from VBA | Table 6 p12 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T6-IQ_CHARGER | IQ_CHARGER: Charger quiescent current 25 °C only; charger in C | Table 6 p12 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T6-IQ_CHARGER_LQM | IQ_CHARGER_LQM: Charger quiescent current (low 25 °C only; charger in C | Table 6 p12 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T6-TSSVBUS_LIN | TSSVBUS_LIN: Soft start time (VBUSIN = 5.0 No input current limitat | Table 6 p12 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T7-VGDRV | VGDRV: Output voltage | Table 7 p13 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T7-IGDRV | IGDRV: Output current | Table 7 p13 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T7-VDOGDRV | VDO(GDRV): Dropout voltage | Table 7 p13 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T8-RVBUS_LIN2SYS | RVBUS_LIN2SYS: VBUSIN to VSYS resistance | Table 8 p13 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T8-RBATFET_QFN | RBATFET_QFN: VBATT to VSYS resistance | Table 8 p13 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T8-ISYS | ISYS: VSYS leakage current VSYS = 0 V, VBATT = 4 | Table 8 p13 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T8-IBATT_OC | IBATT_OC: VBATT reverse ILIM quiescent VBUSIN = 0 V, VSYS = VBA | Table 8 p13 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T9-VPK-PK | VPK-PK: Load transient peak-to-peak VBUSIN = 5.0 V, VBATT = | Table 9 p14 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T9-VOV_SHT | VOV_SHT: Load transient overshoot VBUSIN = 5.0 V, VBATT = | Table 9 p14 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T9-VUND_SHT | VUND_SHT: Load transient undershoot VBUSIN = 5.0 V, VBATT = | Table 9 p14 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T10-VCHGCV_RANGE | VCHGCV_RANGE: CHGCV output voltage range See register map for con | Table 10 p14 | ChargerConfig.charge_voltage_mv grid and <= Limits.cell_max_mv | AppliedCvMv() | T01,T02,T27: tests/test_config.cpp; inc/pf1550_codec.hpp (static_assert); tests/test_review.cpp; tests/test_model.cpp | OK |
| EL-T10-CVACC | CVACC: CHGCV output accuracy in | Table 10 p14 | accuracy band printed in the contract; nominal code compared to Limits (m5) | accuracy not modelled; limit check on nominal | T02,T27: tests/test_config.cpp; tests/test_review.cpp; tests/test_model.cpp | OK |
| EL-T10-VSYSMIN0 | VSYSMIN0: VSYS output voltage (3.5 V VSYSMIN = 0x00 (3.5 V op | Table 10 p14 | ChargerConfig.vsys_min | VSYS minimum | T01,T07: tests/test_config.cpp; inc/pf1550_codec.hpp (static_assert); tests/test_charger.cpp | OK |
| EL-T10-VSYSMIN1 | VSYSMIN1: VSYS output voltage (3.7 V VSYSMIN = 0x01 (3.7 V op | Table 10 p14 | ChargerConfig.vsys_min | VSYS minimum | T01,T07: tests/test_config.cpp; inc/pf1550_codec.hpp (static_assert); tests/test_charger.cpp | OK |
| EL-T10-VSYSMIN2 | VSYSMIN2: VSYS output voltage (4.3 V VSYSMIN = 0x02 (4.3 V op | Table 10 p14 | ChargerConfig.vsys_min | VSYS minimum | T01,T07: tests/test_config.cpp; inc/pf1550_codec.hpp (static_assert); tests/test_charger.cpp | OK |
| EL-T10-VSYSMINLOOP0 | VSYSMINLOOP0: VSYSMIN loop threshold (3.5 V | Table 10 p14 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T10-VSYSMINLOOP1 | VSYSMINLOOP1: VSYSMIN loop threshold (3.7 V | Table 10 p14 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T10-VSYSMINLOOP2 | VSYSMINLOOP2: VSYSMIN loop threshold (4.3 V | Table 10 p14 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T10-IFC | IFC: Output current range Constant current program | Table 10 p14 | ChargerConfig.charge_current_ma grid, <= Limits.cell_max_charge_ma | AppliedCcMa() | T01,T02,T27: tests/test_config.cpp; inc/pf1550_codec.hpp (static_assert); tests/test_review.cpp; tests/test_model.cpp | OK |
| EL-T10-IFCACC1 | IFCACC1: Output current accuracy | Table 10 p14 | accuracy band printed in the contract; nominal code compared to Limits (m5) | accuracy not modelled; limit check on nominal | T02,T27: tests/test_config.cpp; tests/test_review.cpp; tests/test_model.cpp | OK |
| EL-T10-IEOC | IEOC: Charger IEOC range | Table 10 p14 | ChargerConfig.termination_ma / EOC debounce | EOC detect | T01,T07: tests/test_config.cpp; inc/pf1550_codec.hpp (static_assert); tests/test_charger.cpp | OK |
| EL-T10-tDBIEOC | tDB(IEOC): Debounce time for charge | Table 10 p14 | ChargerConfig.termination_ma / EOC debounce | EOC detect | T01,T07: tests/test_config.cpp; inc/pf1550_codec.hpp (static_assert); tests/test_charger.cpp | OK |
| EL-T10-IEOC_ACC_5mA | IEOC_ACC_5mA: Charger IEOC accuracy (5.0 mA IEOC = 5 mA | Table 10 p14 | ack eoc_accuracy_accepted for 5 and 10 mA | EOC detect band | T05,T27: tests/test_config.cpp; tests/test_model.cpp | OK |
| EL-T10-IEOC_ACC_10mA | IEOC_ACC_10mA: Charger IEOC accuracy (10 mA IEOC = 10 mA | Table 10 p14 | ack eoc_accuracy_accepted for 5 and 10 mA | EOC detect band | T05,T27: tests/test_config.cpp; tests/test_model.cpp | OK |
| EL-T10-IEOC_ACC_50mA | IEOC_ACC_50mA: Charger IEOC accuracy (50 mA IEOC = 50 mA | Table 10 p14 | ack eoc_accuracy_accepted for 5 and 10 mA | EOC detect band | T05,T27: tests/test_config.cpp; tests/test_model.cpp | OK |
| EL-T10-VPRECHG | VPRECHG: Precharge threshold VBATT rising | Table 10 p14 | fixed in silicon; status only (precharge threshold code 0 only) | precharge phase | T07: tests/test_charger.cpp | OK |
| EL-T10-VPRECHG_HYS | VPRECHG_HYS: Precharge threshold hysteresis | Table 10 p14 | fixed in silicon; status only (precharge threshold code 0 only) | precharge phase | T07: tests/test_charger.cpp | OK |
| EL-T10-IPRECHG | IPRECHG: Precharge current | Table 10 p14 | fixed in silicon; status only (precharge threshold code 0 only) | precharge phase | T07: tests/test_charger.cpp | OK |
| EL-T10-IPRECHG.LPM | IPRECHG.LPM: Charging current in LPM and 2.8 | Table 10 p14 | fixed in silicon; status only (precharge threshold code 0 only) | precharge phase | T07: tests/test_charger.cpp | OK |
| EL-T10-VRESTART | VRESTART: Charger restart threshold (100 VBATT below CHGCV[5:0] | Table 10 p14 | ChargerConfig.restart | restart logic | T07: tests/test_charger.cpp | OK |
| EL-T10-VRESTART#2 | VRESTART: Charger restart threshold (150 VBATT below CHGCV[5:0] | Table 10 p14 | ChargerConfig.restart | restart logic | T07: tests/test_charger.cpp | OK |
| EL-T10-VRESTART#3 | VRESTART: Charger restart threshold (200 VBATT below CHGCV[5:0] | Table 10 p14 | ChargerConfig.restart | restart logic | T07: tests/test_charger.cpp | OK |
| EL-T10-tDBVRCH | tDB(VRCH): Debounce time on VRESTART | Table 10 p14 | ChargerConfig.restart | restart logic | T07: tests/test_charger.cpp | OK |
| EL-T10-VBATOV | VBATOV: BATTOVP range | Table 10 p14 | status only (BATT_SNS 5, CHG_SNS 9) | battery overvoltage | T08: tests/test_charger.cpp | OK |
| EL-T10-VBATOV_HYS | VBATOV_HYS: BATTOVP hysteresis VBATT falling from BATTOV | Table 10 p14 | status only (BATT_SNS 5, CHG_SNS 9) | battery overvoltage | T08: tests/test_charger.cpp | OK |
| EL-T11-VSPLM | VSPLM: Supplement mode voltage Entering supplement mode | Table 11 p15 | not configurable; supplement mode status | supplement mode | T07: tests/test_charger.cpp | OK |
| EL-T12-tWD | tWD: Watchdog timer period | Table 12 p15 | ChargerConfig.watchdog; service interval <= 16 s | watchdog timer and accuracy | T09: tests/test_charger.cpp | OK |
| EL-T12-tWDACC | tWDACC: Watchdog timer accuracy | Table 12 p15 | ChargerConfig.watchdog; service interval <= 16 s | watchdog timer and accuracy | T09: tests/test_charger.cpp | OK |
| EL-T13-tPRECHG | tPRECHG: Precharge time (fixed 45 mA) Applies to low battery | Table 13 p15 | ChargerConfig timers; driver waits the maximum before trusting a status | scaled timers | T09: tests/test_charger.cpp | OK |
| EL-T13-tFC | tFC: Fast charge constant current Adjustable from 2 to 14 i | Table 13 p15 | ChargerConfig timers; driver waits the maximum before trusting a status | scaled timers | T09: tests/test_charger.cpp | OK |
| EL-T13-tEOC | tEOC: End-of-charge time Adjustable from 0 to 70 i | Table 13 p15 | ChargerConfig timers; driver waits the maximum before trusting a status | scaled timers | T09: tests/test_charger.cpp | OK |
| EL-T13-tacc | tacc: Timer accuracy All timers associated wit | Table 13 p15 | ChargerConfig timers; driver waits the maximum before trusting a status | scaled timers | T09: tests/test_charger.cpp | OK |
| EL-T13-tSCIDG | tSCIDG: Charger state change interrupt | Table 13 p15 | ChargerConfig timers; driver waits the maximum before trusting a status | scaled timers | T09: tests/test_charger.cpp | OK |
| EL-T13-tINLIM | tINLIM: VBUS_VOK delay from VDIG | Table 13 p15 | ChargerConfig timers; driver waits the maximum before trusting a status | scaled timers | T09: tests/test_charger.cpp | OK |
| EL-T14-tBOVCR | tBOVCR: Battery overcurrent debounce Response time to BATFET o | Table 14 p15 | ChargerConfig.batfet.oc_threshold; accuracy band documented (m5) | overcurrent latch and deglitch | T08: tests/test_charger.cpp | OK |
| EL-T14-tBOVCRI | tBOVCRI: Battery overcurrent interrupt Response time to generate | Table 14 p15 | ChargerConfig.batfet.oc_threshold; accuracy band documented (m5) | overcurrent latch and deglitch | T08: tests/test_charger.cpp | OK |
| EL-T14-IBOVCR | IBOVCR: Battery overcurrent threshold Programmable from 2.0 A t | Table 14 p15 | ChargerConfig.batfet.oc_threshold; accuracy band documented (m5) | overcurrent latch and deglitch | T08: tests/test_charger.cpp | OK |
| EL-T14-IBOVCRACC_2A | IBOVCRACC_2A: Battery overcurrent threshold | Table 14 p15 | ChargerConfig.batfet.oc_threshold; accuracy band documented (m5) | overcurrent latch and deglitch | T08: tests/test_charger.cpp | OK |
| EL-T14-IBOVCRACC_3A | IBOVCRACC_3A: Battery overcurrent threshold | Table 14 p15 | ChargerConfig.batfet.oc_threshold; accuracy band documented (m5) | overcurrent latch and deglitch | T08: tests/test_charger.cpp | OK |
| EL-T14-IBOVCRACC_4A | IBOVCRACC_4A: Battery overcurrent threshold | Table 14 p15 | ChargerConfig.batfet.oc_threshold; accuracy band documented (m5) | overcurrent latch and deglitch | T08: tests/test_charger.cpp | OK |
| EL-T14-RSYSDISCH | RSYSDISCH: SYS self-discharge resistor in | Table 14 p15 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T15-TREG | TREG: Thermal regulation threshold (80 Temperature at which charge | Table 15 p16 | ChargerConfig.thermal_reg.temperature | foldback and shutdown | T10: tests/test_configure.cpp; tests/test_charger.cpp | OK |
| EL-T15-TREG#2 | TREG: Thermal regulation threshold (95 Temperature at which charge | Table 15 p16 | ChargerConfig.thermal_reg.temperature | foldback and shutdown | T10: tests/test_configure.cpp; tests/test_charger.cpp | OK |
| EL-T15-TREG#3 | TREG: Thermal regulation threshold Temperature at which char | Table 15 p16 | ChargerConfig.thermal_reg.temperature | foldback and shutdown | T10: tests/test_configure.cpp; tests/test_charger.cpp | OK |
| EL-T16-VNTECREF | VNTECREF: NTECREF voltage | Table 16 p16 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T16-VTN10C | VTN10C: Thermistor threshold (−10 °C −10 °C | Table 16 p16 | ChargerConfig.jeita / thermistor thresholds | thermistor model | T10: tests/test_configure.cpp; tests/test_charger.cpp | OK |
| EL-T16-VT0C | VT0C: Thermistor threshold (0 °C 0 °C | Table 16 p16 | ChargerConfig.jeita / thermistor thresholds | thermistor model | T10: tests/test_configure.cpp; tests/test_charger.cpp | OK |
| EL-T16-VT10C | VT10C: Thermistor threshold (10 °C 10 °C | Table 16 p16 | ChargerConfig.jeita / thermistor thresholds | thermistor model | T10: tests/test_configure.cpp; tests/test_charger.cpp | OK |
| EL-T16-VT45C | VT45C: Thermistor threshold (45 °C 45 °C | Table 16 p16 | ChargerConfig.jeita / thermistor thresholds | thermistor model | T10: tests/test_configure.cpp; tests/test_charger.cpp | OK |
| EL-T16-VT55C | VT55C: Thermistor threshold (55 °C 55 °C | Table 16 p16 | ChargerConfig.jeita / thermistor thresholds | thermistor model | T10: tests/test_configure.cpp; tests/test_charger.cpp | OK |
| EL-T16-VT60C | VT60C: Thermistor threshold (60 °C 60 °C | Table 16 p16 | ChargerConfig.jeita / thermistor thresholds | thermistor model | T10: tests/test_configure.cpp; tests/test_charger.cpp | OK |
| EL-T16-VT_HYS | VT_HYS: Battery temperature hysteresis All settings | Table 16 p16 | ChargerConfig.jeita / thermistor thresholds | thermistor model | T10: tests/test_configure.cpp; tests/test_charger.cpp | OK |
| EL-T17-VUSB_PHY | VUSB_PHY: Output voltage IOUT = 10 mA; 3.3 V and 4 | Table 17 p16 | UsbPhyConfig.voltage | UsbphyMv() | T18: tests/test_power.cpp; tests/test_configure.cpp | OK |
| EL-T17-IUSB_PHY | IUSB_PHY: Maximum output current | Table 17 p16 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T17-USBRDIS | USBRDIS: Internal discharge resistance | Table 17 p16 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T17-USBCAPSTA | USBCAPSTA: Output capacitor for stable 0 µA < IOUT < 60 mA, MAX | Table 17 p16 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T17-IQUSB | IQUSB: Quiescent supply current | Table 17 p16 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T17-USBPHYLDREG | USBPHYLDREG: DC load regulation VBUSIN = 5.5 V, 30 µA < I | Table 17 p16 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T17-USBPHYDO | USBPHYDO: Dropout voltage VBUSIN = 5.0 V, IOUT = 60 | Table 17 p16 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T17-USBPHYILIM | USBPHYILIM: Output current limit | Table 17 p16 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T17-PSRRUSB_PHY | PSRRUSB_PHY: PSRR VBUSIN = 5.5 V, COUT = 1.0 | Table 17 p16 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T18-VLED | VLED: LED input voltage operating | Table 18 p17 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T18-VCHGB_IN | VCHGB_IN: CHGB input voltage operating | Table 18 p17 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T18-ILED | ILED: LED current accuracy | Table 18 p17 | LED_CURRENT fixed code 01 (6 mA) | led current code | T17: tests/test_configure.cpp | OK |
| EL-T18-TON | TON: LED duty cycle range Programmable from 10 % to 1 | Table 18 p17 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T18-TLEDRUP | TLEDRUP: LED ramp up Settings depend on duty cyc | Table 18 p17 | LedConfig.ramp | ramp flag | T17: tests/test_configure.cpp | OK |
| EL-T18-TLEDRDN | TLEDRDN: LED ramp down Settings depend on duty cyc | Table 18 p17 | LedConfig.ramp | ramp flag | T17: tests/test_configure.cpp | OK |
| EL-T18-FLED | FLED: LED frequency Programmable from 0.5 Hz to | Table 18 p17 | LedConfig.frequency | blink period | T17: tests/test_configure.cpp | OK |
| EL-T19-VSWxIN | VSWxIN: Operating input voltage | Table 19 p17 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T19-ISWx | ISWx: Rated output current | Table 19 p17 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T19-VSWx | VSWx: Output voltage accuracy | Table 19 p17 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T19-VSWx#2 | VSWx: Output voltage accuracy | Table 19 p17 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T19-VSWx#3 | VSWx: Output voltage accuracy | Table 19 p17 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T19-VSWx#4 | VSWx: Output voltage accuracy | Table 19 p17 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T19-VSWx#5 | VSWx: Output voltage accuracy | Table 19 p17 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T19-VSWx#6 | VSWx: Output voltage accuracy | Table 19 p17 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T19-VSWx#7 | VSWx: Output voltage accuracy | Table 19 p17 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T19-VSWx#8 | VSWx: Output voltage accuracy | Table 19 p17 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T19-VSWx#9 | ΔVSWx: Output ripple | Table 19 p17 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T19-SWxEFF | SWxEFF: Efficiency | Table 19 p17 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T19-SWxEFF#2 | SWxEFF: Efficiency | Table 19 p17 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T19-SWxEFF#3 | SWxEFF: Efficiency | Table 19 p17 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T19-SWxEFF#4 | SWxEFF: Efficiency | Table 19 p17 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T19-SWxEFF#5 | SWxEFF: Efficiency | Table 19 p17 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T19-ISWxLIMH | ISWxLIMH: Current limiter peak (high-side MOSFET) current detection | Table 19 p17 | BuckConfig.current_limit; limit faults reported | limit fault injection | T01,T15: tests/test_config.cpp; inc/pf1550_codec.hpp (static_assert); tests/test_irq.cpp; tests/test_rails.cpp | OK |
| EL-T19-ISWxLIML | ISWxLIML: Current limiter low-side MOSFET current detection (sinking c | Table 19 p17 | BuckConfig.current_limit; limit faults reported | limit fault injection | T01,T15: tests/test_config.cpp; inc/pf1550_codec.hpp (static_assert); tests/test_irq.cpp; tests/test_rails.cpp | OK |
| EL-T19-ISWxQ | ISWxQ: Quiescent current (at 25 °C) | Table 19 p17 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T19-ISWxQ#2 | ISWxQ: Quiescent current (at 25 °C) | Table 19 p17 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T19-ISWxQ#3 | ISWxQ: Quiescent current (at 25 °C) | Table 19 p17 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T19-ISWxQ#4 | ISWxQ: Quiescent current (at 25 °C) | Table 19 p17 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T19-VSWxOSH | VSWxOSH: Startup overshoot (Normal mode) | Table 19 p17 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T19-tONSWx | tONSWx: Turn on time | Table 19 p17 | driver waits the maximum after enable (DelayUs) before reading status | enable delay | T14,T20: tests/test_rails.cpp; tests/test_configure.cpp | OK |
| EL-T19-VSWxLOTR | VSWxLOTR: Transient load regulation (Normal power mode) | Table 19 p17 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T19-RONSWxP | RONSWxP: SWx P-MOSFET RDS(on) at VSWxIN = 3.6 V | Table 19 p17 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T19-RONSWxN | RONSWxN: SWx N-MOSFET RDS(on) at VSWxIN = 3.6 V | Table 19 p17 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T19-RSWxDIS | RSWxDIS: Turn off discharge resistance | Table 19 p17 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T20-VSW3IN | VSW3IN: Operating input voltage | Table 20 p19 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T20-VSW3 | VSW3: Output voltage accuracy (all voltage settings) | Table 20 p19 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T20-VSW3#2 | VSW3: Output voltage accuracy (all voltage settings) | Table 20 p19 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T20-VSW3#3 | ΔVSW3: Output ripple | Table 20 p19 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T20-SW3EFF | SW3EFF: VSW3IN = 3.6 V, LSW3 = 1.0 µH, DCR = 50 mΩ | Table 20 p19 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T20-SW3EFF#2 | SW3EFF: VSW3IN = 3.6 V, LSWx = 1.0 µH, DCR = 50 mΩ | Table 20 p19 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T20-SW3EFF#3 | SW3EFF: VSW3IN = 3.6 V, LSWx = 1.0 mH, DCR = 50 mΩ | Table 20 p19 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T20-SW3EFF#4 | SW3EFF: VSW3IN = 3.6 V, LSWx = 1.0 µH, DCR = 50 mΩ | Table 20 p19 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T20-SW3EFF#5 | SW3EFF: VSW3IN = 3.6 V, LSWx = 1.0 µH, DCR = 50 mΩ | Table 20 p19 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T20-ISW3LIMH | ISW3LIMH: Current limiter peak (high-side MOSFET) current detection | Table 20 p19 | BuckConfig.current_limit; limit faults reported | limit fault injection | T01,T15: tests/test_config.cpp; inc/pf1550_codec.hpp (static_assert); tests/test_irq.cpp; tests/test_rails.cpp | OK |
| EL-T20-ISW3LIML | ISW3LIML: Current limiter low-side MOSFET current detection (sinking c | Table 20 p19 | BuckConfig.current_limit; limit faults reported | limit fault injection | T01,T15: tests/test_config.cpp; inc/pf1550_codec.hpp (static_assert); tests/test_irq.cpp; tests/test_rails.cpp | OK |
| EL-T20-ISW3Q | ISW3Q: Quiescent current (at 25 °C) | Table 20 p19 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T20-VSW3OSH | VSW3OSH: Start-up overshoot (Normal mode) | Table 20 p19 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T20-tONSW3 | tONSW3: Turn on time | Table 20 p19 | driver waits the maximum after enable (DelayUs) before reading status | enable delay | T14,T20: tests/test_rails.cpp; tests/test_configure.cpp | OK |
| EL-T20-VSW3LOTR | VSW3LOTR: Transient load regulation (Normal power mode) | Table 20 p19 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T20-RONSW3N | RONSW3N: SW3 N-MOSFET RDS(on) at VSW3IN = 3.6 V | Table 20 p19 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T20-RONSW3P | RONSW3P: SW3 P-MOSFET RDS(on) at VSW3IN = 3.6 V | Table 20 p19 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T20-RSW3DIS | RSW3DIS: Turn off discharge resistance | Table 20 p19 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T21-VLDO1IN | VLDO1IN: Operating input voltage | Table 21 p20 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T21-VLDO1NOM | VLDO1NOM: Nominal output voltage | Table 21 p20 | LdoConfig.volt grid inside RailLimits | code table | T01,T27: tests/test_config.cpp; inc/pf1550_codec.hpp (static_assert); tests/test_model.cpp | OK |
| EL-T21-ILDO1MAX | ILDO1MAX: Rated output load current, Normal mode | Table 21 p20 | RailLimits.max_load_ma declared by the application | not modelled; compared in Validate | T02,T27: tests/test_config.cpp; tests/test_review.cpp; tests/test_model.cpp | OK |
| EL-T21-ILDO1MAXLPM | ILDO1MAXLPM: Rated output load current, Low-power mode | Table 21 p20 | LdoConfig.modes.low_power needs ack load_below_10ma | LPWR flag | T14,T05: tests/test_rails.cpp; tests/test_configure.cpp; tests/test_config.cpp | OK |
| EL-T21-VLDO1TOL | VLDO1TOL: Output voltage tolerance, Normal mode | Table 21 p20 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T21-ILDO1LIM | ILDO1LIM: Current limit | Table 21 p20 | LDO fault interrupt reported; REGSCPEN typed | fault injection | T15: tests/test_irq.cpp; tests/test_rails.cpp | OK |
| EL-T21-ILDO1OCP | ILDO1OCP: LDO1FAULTI threshold (also used to disable LDO1 when | Table 21 p20 | LDO fault interrupt reported; REGSCPEN typed | fault injection | T15: tests/test_irq.cpp; tests/test_rails.cpp | OK |
| EL-T21-ILDO1Q | ILDO1Q: Quiescent current (at 25 °C) | Table 21 p20 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T21-RDSON_QFN_LDO1 | RDSON_QFN_LDO1: Dropout on resistance | Table 21 p20 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T21-PSRRLDO1 | PSRRLDO1: PSRR | Table 21 p20 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T21-TRVLDO1 | TRVLDO1: Turn on time | Table 21 p20 | driver waits the maximum after enable (DelayUs) | enable delay | T14,T20: tests/test_rails.cpp; tests/test_configure.cpp | OK |
| EL-T21-RLDO1DIS | RLDO1DIS: Turn off discharge resistance | Table 21 p20 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T21-LDO1OUTOSHT | LDO1OUTOSHT: Start-up overshoot (% of final value) | Table 21 p20 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T21-VLDO1LOTR | VLDO1LOTR: Transient load response | Table 21 p20 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T22-VLDO2IN | VLDO2IN: Operating input voltage | Table 22 p20 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T22-VLDO2NOM | VLDO2NOM: Nominal output voltage | Table 22 p20 | LdoConfig.volt grid inside RailLimits | code table | T01,T27: tests/test_config.cpp; inc/pf1550_codec.hpp (static_assert); tests/test_model.cpp | OK |
| EL-T22-ILDO2MAX | ILDO2MAX: Rated output load current, Normal mode | Table 22 p20 | RailLimits.max_load_ma declared by the application | not modelled; compared in Validate | T02,T27: tests/test_config.cpp; tests/test_review.cpp; tests/test_model.cpp | OK |
| EL-T22-ILDO2MAXLPM | ILDO2MAXLPM: Rated output load current, Low-power mode | Table 22 p20 | LdoConfig.modes.low_power needs ack load_below_10ma | LPWR flag | T14,T05: tests/test_rails.cpp; tests/test_configure.cpp; tests/test_config.cpp | OK |
| EL-T22-VLDO2TOL | VLDO2TOL: Output voltage tolerance | Table 22 p20 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T22-ILDO2LIM | ILDO2LIM: Current limit | Table 22 p20 | LDO fault interrupt reported; REGSCPEN typed | fault injection | T15: tests/test_irq.cpp; tests/test_rails.cpp | OK |
| EL-T22-ILDO2OCP | ILDO2OCP: LDO2FAULTI threshold (also used to disable LDO2 when 450 | Table 22 p20 | LDO fault interrupt reported; REGSCPEN typed | fault injection | T15: tests/test_irq.cpp; tests/test_rails.cpp | OK |
| EL-T22-ILDO2Q | ILDO2Q: Quiescent Current (25 °C) | Table 22 p20 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T22-RDSON_QFN_LDO2 | RDSON_QFN_LDO2: Dropout on resistance | Table 22 p20 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T22-PSRRVLDO2 | PSRRVLDO2: PSRR | Table 22 p20 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T22-tONLDO2 | tONLDO2: Turn on time | Table 22 p20 | driver waits the maximum after enable (DelayUs) | enable delay | T14,T20: tests/test_rails.cpp; tests/test_configure.cpp | OK |
| EL-T22-RLDO2DIS | RLDO2DIS: Turn off discharge resistance | Table 22 p20 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T22-LDO2OUTOSHT | LDO2OUTOSHT: Start-up overshoot (% of final value) | Table 22 p20 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T22-VLDO2LOTR | VLDO2LOTR: Transient load response | Table 22 p20 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T23-VLDO3IN | VLDO3IN: Operating input voltage | Table 23 p21 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T23-VLDO3NOM | VLDO3NOM: Nominal output voltage | Table 23 p21 | LdoConfig.volt grid inside RailLimits | code table | T01,T27: tests/test_config.cpp; inc/pf1550_codec.hpp (static_assert); tests/test_model.cpp | OK |
| EL-T23-ILDO3MAX | ILDO3MAX: Rated output load current, Normal mode | Table 23 p21 | RailLimits.max_load_ma declared by the application | not modelled; compared in Validate | T02,T27: tests/test_config.cpp; tests/test_review.cpp; tests/test_model.cpp | OK |
| EL-T23-ILDO3MAXLPM | ILDO3MAXLPM: Rated output load current, Low-power mode | Table 23 p21 | LdoConfig.modes.low_power needs ack load_below_10ma | LPWR flag | T14,T05: tests/test_rails.cpp; tests/test_configure.cpp; tests/test_config.cpp | OK |
| EL-T23-VLDO3TOL | VLDO3TOL: Output voltage tolerance, Normal mode | Table 23 p21 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T23-ILDO3LIM | ILDO3LIM: Current limit | Table 23 p21 | LDO fault interrupt reported; REGSCPEN typed | fault injection | T15: tests/test_irq.cpp; tests/test_rails.cpp | OK |
| EL-T23-ILDO3OCP | ILDO3OCP: LDO3FAULTI threshold (also used to disable LDO3 when 320 | Table 23 p21 | LDO fault interrupt reported; REGSCPEN typed | fault injection | T15: tests/test_irq.cpp; tests/test_rails.cpp | OK |
| EL-T23-ILDO3Q | ILDO3Q: Quiescent current (at 25 °C) | Table 23 p21 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T23-RDSON_QFN_LDO3 | RDSON_QFN_LDO3: Dropout on resistance | Table 23 p21 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T23-PSRRLDO3 | PSRRLDO3: PSRR | Table 23 p21 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T23-TRVLDO3 | TRVLDO3: Turn on time | Table 23 p21 | driver waits the maximum after enable (DelayUs) | enable delay | T14,T20: tests/test_rails.cpp; tests/test_configure.cpp | OK |
| EL-T23-RLDO3DIS | RLDO3DIS: Turn off discharge resistance | Table 23 p21 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T23-LDO3OUTOSHT | LDO3OUTOSHT: Start-up overshoot (% of final value) | Table 23 p21 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T23-VLDO3LOTR | VLDO3LOTR: Transient load response | Table 23 p21 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T24-VINREFDDR | VINREFDDR: Operating input voltage range | Table 24 p22 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T24-VREFDDR | VREFDDR: Output voltage, 0.9 V < VINREFDDR < 1.8 V, 0 mA < IREFDDR < | Table 24 p22 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T24-VREFDDRTOL | VREFDDRTOL: Output voltage tolerance, as a percentage of VINREFDDR, 1.2 | Table 24 p22 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T24-IREFDDRQ | IREFDDRQ: Quiescent current (at 25 °C) | Table 24 p22 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T24-IREFDDRLM | IREFDDRLM: Current limit, IREFDDR when VREFDDR is forced to VINREFDDR/4 | Table 24 p22 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T24-tONREFDDR | tONREFDDR: Turn on time, 10 % to 90 % of end value, VINREFDDR = 1.2 V t | Table 24 p22 | driver waits the maximum after enable | enable delay | T18,T20: tests/test_power.cpp; tests/test_configure.cpp | OK |
| EL-T25-VSNVSIN | VSNVSIN: Operating input voltage | Table 25 p22 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T25-ISNVS | ISNVS: Operating load current | Table 25 p22 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T25-VTL1 | VTL1: VSYS threshold (VSYS powered to coin cell powered) | Table 25 p22 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T25-VTH1 | VTH1: VSYS threshold (coin cell powered to VSYS powered) | Table 25 p22 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T25-VSNVS | VSNVS: Output voltage (when running from VSYS) | Table 25 p22 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T25-VSNVSDROP | VSNVSDROP: Dropout voltage | Table 25 p22 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T25-ISNVSLIM | ISNVSLIM: Current limit | Table 25 p22 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T25-VSNVSTON | VSNVSTON: Turn on time (load capacitor, 0.47 µF) | Table 25 p22 | driver waits the maximum after enable | enable delay | T18,T20: tests/test_power.cpp; tests/test_configure.cpp | OK |
| EL-T25-VSNVSOSH | VSNVSOSH: Start-up overshoot | Table 25 p22 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T25-RDSONSNVS | RDSONSNVS: Internal switch RDS(on) | Table 25 p22 | not applicable: analog value of an on-chip block, no register and no driver decision (hardware page lists it) | not modelled | N/A: no driver decision | INFO |
| EL-T26-Coin cell | IC quiescent current in Coin cell: VSNVS from LICELL, all other blocks off | Table 26 p23 | not applicable: supply current figure; documented on the hardware page | not modelled | N/A: no driver decision | INFO |
| EL-T26-CORE_OFF | IC quiescent current in CORE_OFF: wake-up from ONKEY | Table 26 p23 | not applicable: supply current figure; documented on the hardware page | not modelled | N/A: no driver decision | INFO |
| EL-T26-Sleep | IC quiescent current in Sleep: DDR self-refresh, wake from PWRON | Table 26 p23 | not applicable: supply current figure; documented on the hardware page | not modelled | N/A: no driver decision | INFO |
| EL-T26-Standby/Suspend | IC quiescent current in Standby/Suspend: SW low-power, LDO⅔ low-power | Table 26 p23 | not applicable: supply current figure; documented on the hardware page | not modelled | N/A: no driver decision | INFO |
| EL-T26-REGS_DISABLE | IC quiescent current in REGS_DISABLE: wake from ONKEY | Table 26 p23 | not applicable: supply current figure; documented on the hardware page | not modelled | N/A: no driver decision | INFO |
| EL-T26-SHIP | IC quiescent current in SHIP: BATFET open, only ONKEY awake | Table 26 p23 | not applicable: supply current figure; documented on the hardware page | not modelled | N/A: no driver decision | INFO |
Start-up and power-down timing (T84)¶
| Id | Item | Datasheet | API | Model | Test | Status |
|---|---|---|---|---|---|---|
| TM-T84-tD1 | tD1: turn-on delay of VSNVS 0.6 ms | Table 84 p79 | kVsnvsTurnOnDelayUs, kSlotFastUs, kSlotSlowUs, kPowerDownStepUs, ColdStartToResetReleaseUs(), PowerDownDelayUs() | sequencer runs the slots of Table 84 | T19: tests/test_lifecycle.cpp; tests/test_model.cpp | OK |
| TM-T84-tR1 | tR1: rise time of VSNVS | Table 84 p79 | not applicable: analog rise time or the application's own delay | not modelled | N/A: no driver decision | INFO |
| TM-T84-tD2 | tD2: user-determined delay | Table 84 p79 | not applicable: analog rise time or the application's own delay | not modelled | N/A: no driver decision | INFO |
| TM-T84-tR2 | tR2: rise time of PWRON | Table 84 p79 | not applicable: analog rise time or the application's own delay | not modelled | N/A: no driver decision | INFO |
| TM-T84-tD3SEQCLKSPEED0 | tD3 (SEQ_CLK_SPEED 0): delay between regulators 0.5 ms | Table 84 p79 | kVsnvsTurnOnDelayUs, kSlotFastUs, kSlotSlowUs, kPowerDownStepUs, ColdStartToResetReleaseUs(), PowerDownDelayUs() | sequencer runs the slots of Table 84 | T19: tests/test_lifecycle.cpp; tests/test_model.cpp | OK |
| TM-T84-tD3SEQCLKSPEED1 | tD3 (SEQ_CLK_SPEED 1): delay between regulators 2.0 ms | Table 84 p79 | kVsnvsTurnOnDelayUs, kSlotFastUs, kSlotSlowUs, kPowerDownStepUs, ColdStartToResetReleaseUs(), PowerDownDelayUs() | sequencer runs the slots of Table 84 | T19: tests/test_lifecycle.cpp; tests/test_model.cpp | OK |
| TM-T84-tR3 | tR3: rise time of regulators | Table 84 p79 | not applicable: analog rise time or the application's own delay | not modelled | N/A: no driver decision | INFO |
| TM-T84-tD4 | tD4: turn-on delay of RESETBMCU 2.0 ms | Table 84 p79 | kVsnvsTurnOnDelayUs, kSlotFastUs, kSlotSlowUs, kPowerDownStepUs, ColdStartToResetReleaseUs(), PowerDownDelayUs() | sequencer runs the slots of Table 84 | T19: tests/test_lifecycle.cpp; tests/test_model.cpp | OK |
| TM-T84-tR4 | tR4: rise time of RESETBMCU | Table 84 p79 | not applicable: analog rise time or the application's own delay | not modelled | N/A: no driver decision | INFO |
| TM-T84-tD5 | tD5: power-down delay between regulators 2.0 ms | Table 84 p79 | kVsnvsTurnOnDelayUs, kSlotFastUs, kSlotSlowUs, kPowerDownStepUs, ColdStartToResetReleaseUs(), PowerDownDelayUs() | sequencer runs the slots of Table 84 | T19: tests/test_lifecycle.cpp; tests/test_model.cpp | OK |
Digital pin levels, debounce and polarity (T73 to T82)¶
| Id | Item | Datasheet | API | Model | Test | Status |
|---|---|---|---|---|---|---|
| PL-T74-PWRON.VIL | PWRON VIL (0.4 V max / 1.4 V min, 3.6 V max) | Table 74 p68 | not applicable: logic level of the board wiring; hardware page lists it; the port provides GPIO levels | pin events modelled as logic levels (no voltage) | N/A: no driver decision | INFO |
| PL-T74-PWRON.VIH | PWRON VIH (0.4 V max / 1.4 V min, 3.6 V max) | Table 74 p68 | not applicable: logic level of the board wiring; hardware page lists it; the port provides GPIO levels | pin events modelled as logic levels (no voltage) | N/A: no driver decision | INFO |
| PL-T77-STANDBY.VIL | STANDBY VIL (0.4 / 1.4 V) | Table 77 p69 | not applicable: logic level of the board wiring; hardware page lists it; the port provides GPIO levels | pin events modelled as logic levels (no voltage) | N/A: no driver decision | INFO |
| PL-T77-STANDBY.VIH | STANDBY VIH (0.4 / 1.4 V) | Table 77 p69 | not applicable: logic level of the board wiring; hardware page lists it; the port provides GPIO levels | pin events modelled as logic levels (no voltage) | N/A: no driver decision | INFO |
| PL-T78-RESETBMCU.VOL | RESETBMCU VOL (0.2 x VDDIO at -2 mA / 0.8 x VDDIO) | Table 78 p70 | not applicable: logic level of the board wiring; hardware page lists it; the port provides GPIO levels | pin events modelled as logic levels (no voltage) | N/A: no driver decision | INFO |
| PL-T78-RESETBMCU.VOH | RESETBMCU VOH (0.2 x VDDIO at -2 mA / 0.8 x VDDIO) | Table 78 p70 | not applicable: logic level of the board wiring; hardware page lists it; the port provides GPIO levels | pin events modelled as logic levels (no voltage) | N/A: no driver decision | INFO |
| PL-T79-INTB.VOL | INTB VOL (0.2 x VDDIO at -2 mA / 0.8 x VDDIO) | Table 79 p70 | not applicable: logic level of the board wiring; hardware page lists it; the port provides GPIO levels | pin events modelled as logic levels (no voltage) | N/A: no driver decision | INFO |
| PL-T79-INTB.VOH | INTB VOH (0.2 x VDDIO at -2 mA / 0.8 x VDDIO) | Table 79 p70 | not applicable: logic level of the board wiring; hardware page lists it; the port provides GPIO levels | pin events modelled as logic levels (no voltage) | N/A: no driver decision | INFO |
| PL-T80-WDI.VIL | WDI VIL (0.2 / 0.8 x VDDIO) | Table 80 p70 | not applicable: logic level of the board wiring; hardware page lists it; the port provides GPIO levels | pin events modelled as logic levels (no voltage) | N/A: no driver decision | INFO |
| PL-T80-WDI.VIH | WDI VIH (0.2 / 0.8 x VDDIO) | Table 80 p70 | not applicable: logic level of the board wiring; hardware page lists it; the port provides GPIO levels | pin events modelled as logic levels (no voltage) | N/A: no driver decision | INFO |
| PL-T81-ONKEY.VIL | ONKEY VIL (0.4 / 1.4 V, 4.8 V max) | Table 81 p71 | not applicable: logic level of the board wiring; hardware page lists it; the port provides GPIO levels | pin events modelled as logic levels (no voltage) | N/A: no driver decision | INFO |
| PL-T81-ONKEY.VIH | ONKEY VIH (0.4 / 1.4 V, 4.8 V max) | Table 81 p71 | not applicable: logic level of the board wiring; hardware page lists it; the port provides GPIO levels | pin events modelled as logic levels (no voltage) | N/A: no driver decision | INFO |
| PL-T75-003125ms | PWRONDBNC 00: 31.25 ms | Table 75 p69 | PowerConfig.pwron_debounce/onkey_debounce/standby_inverted | debounce / polarity logic in the model | T13,T20: tests/test_power.cpp; tests/test_configure.cpp | OK |
| PL-T75-013125ms | PWRONDBNC 01: 31.25 ms | Table 75 p69 | PowerConfig.pwron_debounce/onkey_debounce/standby_inverted | debounce / polarity logic in the model | T13,T20: tests/test_power.cpp; tests/test_configure.cpp | OK |
| PL-T75-10125ms | PWRONDBNC 10: 125 ms | Table 75 p69 | PowerConfig.pwron_debounce/onkey_debounce/standby_inverted | debounce / polarity logic in the model | T13,T20: tests/test_power.cpp; tests/test_configure.cpp | OK |
| PL-T75-11750ms | PWRONDBNC 11: 750 ms | Table 75 p69 | PowerConfig.pwron_debounce/onkey_debounce/standby_inverted | debounce / polarity logic in the model | T13,T20: tests/test_power.cpp; tests/test_configure.cpp | OK |
| PL-T82-003125ms | ONKEYDBNC 00: 31.25 ms | Table 82 p71 | PowerConfig.pwron_debounce/onkey_debounce/standby_inverted | debounce / polarity logic in the model | T13,T20: tests/test_power.cpp; tests/test_configure.cpp | OK |
| PL-T82-013125ms | ONKEYDBNC 01: 31.25 ms | Table 82 p71 | PowerConfig.pwron_debounce/onkey_debounce/standby_inverted | debounce / polarity logic in the model | T13,T20: tests/test_power.cpp; tests/test_configure.cpp | OK |
| PL-T82-10125ms | ONKEYDBNC 10: 125 ms | Table 82 p71 | PowerConfig.pwron_debounce/onkey_debounce/standby_inverted | debounce / polarity logic in the model | T13,T20: tests/test_power.cpp; tests/test_configure.cpp | OK |
| PL-T82-11750ms | ONKEYDBNC 11: 750 ms | Table 82 p71 | PowerConfig.pwron_debounce/onkey_debounce/standby_inverted | debounce / polarity logic in the model | T13,T20: tests/test_power.cpp; tests/test_configure.cpp | OK |
| PL-T76-pin0INV0notstandby | STANDBY polarity pin 0, INV 0: not standby | Table 76 p69 | PowerConfig.pwron_debounce/onkey_debounce/standby_inverted | debounce / polarity logic in the model | T13,T20: tests/test_power.cpp; tests/test_configure.cpp | OK |
| PL-T76-pin0INV1standby | STANDBY polarity pin 0, INV 1: standby | Table 76 p69 | PowerConfig.pwron_debounce/onkey_debounce/standby_inverted | debounce / polarity logic in the model | T13,T20: tests/test_power.cpp; tests/test_configure.cpp | OK |
| PL-T76-pin1INV0standby | STANDBY polarity pin 1, INV 0: standby | Table 76 p69 | PowerConfig.pwron_debounce/onkey_debounce/standby_inverted | debounce / polarity logic in the model | T13,T20: tests/test_power.cpp; tests/test_configure.cpp | OK |
| PL-T76-pin1INV1notstandby | STANDBY polarity pin 1, INV 1: not standby | Table 76 p69 | PowerConfig.pwron_debounce/onkey_debounce/standby_inverted | debounce / polarity logic in the model | T13,T20: tests/test_power.cpp; tests/test_configure.cpp | OK |
| PL-T73 | PWRON pin OTP configuration options (level or edge, OTP_PWRON_CFG) | Table 73 p68 | Config.pwron_edge declaration (C38) | both columns of Table 83 | T13: tests/test_power.cpp | OK |
Pins (T2)¶
| Id | Item | Datasheet | API | Model | Test | Status |
|---|---|---|---|---|---|---|
| PIN-01 | Pin 1 WDI | Table 2 p8-9 | none: documented; low forces REGS_DISABLE (T83 G) | modelled as an event or level | T13: tests/test_power.cpp | OK |
| PIN-02 | Pin 2 SDA | Table 2 p8-9 | i2c port | modelled as an event or level | T21: tests/test_lifecycle.cpp; tests/test_errors.cpp | OK |
| PIN-03 | Pin 3 SCL | Table 2 p8-9 | i2c port | modelled as an event or level | T21: tests/test_lifecycle.cpp; tests/test_errors.cpp | OK |
| PIN-04 | Pin 4 VDDIO | Table 2 p8-9 | none | not modelled | N/A: wiring | INFO |
| PIN-05 | Pin 5 VDDOTP | Table 2 p8-9 | none (ground) | not modelled | N/A: wiring | INFO |
| PIN-06 | Pin 6 PWRON | Table 2 p8-9 | none: event input of the model | modelled as an event or level | T13: tests/test_power.cpp | OK |
| PIN-07 | Pin 7 STANDBY | Table 2 p8-9 | standby hook (optional GpioSet) | modelled as an event or level | T13: tests/test_power.cpp | OK |
| PIN-08 | Pin 8 ONKEY | Table 2 p8-9 | none: event input of the model | modelled as an event or level | T13: tests/test_power.cpp | OK |
| PIN-09 | Pin 9 INTB | Table 2 p8-9 | intb hook (optional GpioGet) | modelled as an event or level | T12: tests/test_irq.cpp | OK |
| PIN-10 | Pin 10 RESETBMCU | Table 2 p8-9 | none | not modelled | N/A: wiring | INFO |
| PIN-11 | Pin 11 VLDO3IN | Table 2 p8-9 | none | not modelled | N/A: wiring | INFO |
| PIN-12 | Pin 12 VLDO3 | Table 2 p8-9 | none | not modelled | N/A: wiring | INFO |
| PIN-13 | Pin 13 SW3LX | Table 2 p8-9 | none | not modelled | N/A: wiring | INFO |
| PIN-14 | Pin 14 SW3IN | Table 2 p8-9 | none | not modelled | N/A: wiring | INFO |
| PIN-15 | Pin 15 SW3FB | Table 2 p8-9 | none | not modelled | N/A: wiring | INFO |
| PIN-16 | Pin 16 SW2FB | Table 2 p8-9 | none | not modelled | N/A: wiring | INFO |
| PIN-17 | Pin 17 SW2IN | Table 2 p8-9 | none | not modelled | N/A: wiring | INFO |
| PIN-18 | Pin 18 SW2LX | Table 2 p8-9 | none | not modelled | N/A: wiring | INFO |
| PIN-19 | Pin 19 VLDO2 | Table 2 p8-9 | none | not modelled | N/A: wiring | INFO |
| PIN-20 | Pin 20 VLDO2IN | Table 2 p8-9 | none | not modelled | N/A: wiring | INFO |
| PIN-21 | Pin 21 VREFDDR | Table 2 p8-9 | none | not modelled | N/A: wiring | INFO |
| PIN-22 | Pin 22 VINREFDDR | Table 2 p8-9 | none | not modelled | N/A: wiring | INFO |
| PIN-23 | Pin 23 VDIG | Table 2 p8-9 | none | not modelled | N/A: wiring | INFO |
| PIN-24 | Pin 24 VCORE | Table 2 p8-9 | none | not modelled | N/A: wiring | INFO |
| PIN-25 | Pin 25 SW1LX | Table 2 p8-9 | none | not modelled | N/A: wiring | INFO |
| PIN-26 | Pin 26 SW1IN | Table 2 p8-9 | none | not modelled | N/A: wiring | INFO |
| PIN-27 | Pin 27 SW1FB | Table 2 p8-9 | none | not modelled | N/A: wiring | INFO |
| PIN-28 | Pin 28 VLDO1IN | Table 2 p8-9 | none | not modelled | N/A: wiring | INFO |
| PIN-29 | Pin 29 VLDO1 | Table 2 p8-9 | none | not modelled | N/A: wiring | INFO |
| PIN-30 | Pin 30 VSNVS | Table 2 p8-9 | none | not modelled | N/A: wiring | INFO |
| PIN-31 | Pin 31 LICELL | Table 2 p8-9 | none | not modelled | N/A: wiring | INFO |
| PIN-32 | Pin 32 THM | Table 2 p8-9 | none | not modelled | N/A: wiring | INFO |
| PIN-33 | Pin 33 VBATT | Table 2 p8-9 | none | not modelled | N/A: wiring | INFO |
| PIN-34 | Pin 34 VBATT | Table 2 p8-9 | none | not modelled | N/A: wiring | INFO |
| PIN-35 | Pin 35 VSYS | Table 2 p8-9 | none | not modelled | N/A: wiring | INFO |
| PIN-36 | Pin 36 VSYS | Table 2 p8-9 | none | not modelled | N/A: wiring | INFO |
| PIN-37 | Pin 37 VBUSIN | Table 2 p8-9 | none | not modelled | N/A: wiring | INFO |
| PIN-38 | Pin 38 INT2P7 | Table 2 p8-9 | none | not modelled | N/A: wiring | INFO |
| PIN-39 | Pin 39 USBPHY | Table 2 p8-9 | none | not modelled | N/A: wiring | INFO |
| PIN-40 | Pin 40 CHGB | Table 2 p8-9 | none | not modelled | N/A: wiring | INFO |
| PIN-41 | Pin 41 EPAD | Table 2 p8-9 | none | not modelled | N/A: wiring | INFO |
OTP start-up values (T85, per parameter)¶
| Id | Item | Datasheet | API | Model | Test | Status |
|---|---|---|---|---|---|---|
| OV-DefaultI2Caddress | Default I2C address per option A1..A9 | Table 85 p79-80 | not exposed: fuse value, readable only through VariantInfo.i2c_slave_addr_code | model option table loads the value into the register at power-up; per-option test T19 | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OV-OTP_VSNVS_VOLT20 | OTP_VSNVS_VOLT[2:0] per option A1..A9 | Table 85 p79-80 | not exposed: fuse value, readable only through Snapshot (register loaded from this fuse) | model option table loads the value into the register at power-up; per-option test T19 | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OV-OTP_SW1_VOLT50 | OTP_SW1_VOLT[5:0] per option A1..A9 | Table 85 p79-80 | not exposed: fuse value, readable only through Snapshot (register loaded from this fuse) | model option table loads the value into the register at power-up; per-option test T19 | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OV-OTP_SW1_PWRUP_SEQ20 | OTP_SW1_PWRUP_SEQ[2:0] per option A1..A9 | Table 85 p79-80 | StartupProfileOf(Option): order and slot time of options A1 to A9 (Table 85); the fuse itself is not readable | option table; the model runs the power-up sequence | T19: tests/test_lifecycle.cpp; tests/test_model.cpp | OK |
| OV-OTP_SW2_VOLT50 | OTP_SW2_VOLT[5:0] per option A1..A9 | Table 85 p79-80 | not exposed: fuse value, readable only through Snapshot (register loaded from this fuse) | model option table loads the value into the register at power-up; per-option test T19 | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OV-OTP_SW2_PWRUP_SEQ20 | OTP_SW2_PWRUP_SEQ[2:0] per option A1..A9 | Table 85 p79-80 | StartupProfileOf(Option): order and slot time of options A1 to A9 (Table 85); the fuse itself is not readable | option table; the model runs the power-up sequence | T19: tests/test_lifecycle.cpp; tests/test_model.cpp | OK |
| OV-OTP_SW3_VOLT50 | OTP_SW3_VOLT[5:0] per option A1..A9 | Table 85 p79-80 | not exposed: fuse value, readable only through Snapshot (register loaded from this fuse) | model option table loads the value into the register at power-up; per-option test T19 | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OV-OTP_SW3_PWRUP_SEQ20 | OTP_SW3_PWRUP_SEQ[2:0] per option A1..A9 | Table 85 p79-80 | StartupProfileOf(Option): order and slot time of options A1 to A9 (Table 85); the fuse itself is not readable | option table; the model runs the power-up sequence | T19: tests/test_lifecycle.cpp; tests/test_model.cpp | OK |
| OV-OTP_LDO1_VOLT40 | OTP_LDO1_VOLT[4:0] per option A1..A9 | Table 85 p79-80 | not exposed: fuse value, readable only through Snapshot (register loaded from this fuse) | model option table loads the value into the register at power-up; per-option test T19 | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OV-OTP_LDO1_PWRUP_SEQ20 | OTP_LDO1_PWRUP_SEQ[2:0] per option A1..A9 | Table 85 p79-80 | StartupProfileOf(Option): order and slot time of options A1 to A9 (Table 85); the fuse itself is not readable | option table; the model runs the power-up sequence | T19: tests/test_lifecycle.cpp; tests/test_model.cpp | OK |
| OV-OTP_LDO2_VOLT30 | OTP_LDO2_VOLT[3:0] per option A1..A9 | Table 85 p79-80 | not exposed: fuse value, readable only through Snapshot (register loaded from this fuse) | model option table loads the value into the register at power-up; per-option test T19 | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OV-OTP_LDO2_PWRUP_SEQ20 | OTP_LDO2_PWRUP_SEQ[2:0] per option A1..A9 | Table 85 p79-80 | StartupProfileOf(Option): order and slot time of options A1 to A9 (Table 85); the fuse itself is not readable | option table; the model runs the power-up sequence | T19: tests/test_lifecycle.cpp; tests/test_model.cpp | OK |
| OV-OTP_LDO3_VOLT40 | OTP_LDO3_VOLT[4:0] per option A1..A9 | Table 85 p79-80 | not exposed: fuse value, readable only through Snapshot (register loaded from this fuse) | model option table loads the value into the register at power-up; per-option test T19 | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OV-OTP_LDO3_PWRUP_SEQ20 | OTP_LDO3_PWRUP_SEQ[2:0] per option A1..A9 | Table 85 p79-80 | StartupProfileOf(Option): order and slot time of options A1 to A9 (Table 85); the fuse itself is not readable | option table; the model runs the power-up sequence | T19: tests/test_lifecycle.cpp; tests/test_model.cpp | OK |
| OV-OTP_VREFDDR_PWRUP_SEQ20 | OTP_VREFDDR_PWRUP_SEQ[2:0] per option A1..A9 | Table 85 p79-80 | StartupProfileOf(Option): order and slot time of options A1 to A9 (Table 85); the fuse itself is not readable | option table; the model runs the power-up sequence | T19: tests/test_lifecycle.cpp; tests/test_model.cpp | OK |
| OV-OTP_SW1_DVS_SEL | OTP_SW1_DVS_SEL per option A1..A9 | Table 85 p79-80 | not exposed: fuse value, readable only through Snapshot (register loaded from this fuse) | model option table loads the value into the register at power-up; per-option test T19 | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OV-OTP_SW2_DVS_SEL | OTP_SW2_DVS_SEL per option A1..A9 | Table 85 p79-80 | not exposed: fuse value, readable only through Snapshot (register loaded from this fuse) | model option table loads the value into the register at power-up; per-option test T19 | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OV-OTP_LDO1_LS_EN | OTP_LDO1_LS_EN per option A1..A9 | Table 85 p79-80 | not exposed: fuse value, readable only through Snapshot (register loaded from this fuse) | model option table loads the value into the register at power-up; per-option test T19 | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OV-OTP_LDO3_LS_EN | OTP_LDO3_LS_EN per option A1..A9 | Table 85 p79-80 | not exposed: fuse value, readable only through Snapshot (register loaded from this fuse) | model option table loads the value into the register at power-up; per-option test T19 | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OV-OTP_SW1_RDIS_ENB | OTP_SW1_RDIS_ENB per option A1..A9 | Table 85 p79-80 | not exposed: fuse value, readable only through Snapshot (register loaded from this fuse) | model option table loads the value into the register at power-up; per-option test T19 | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OV-OTP_SW2_RDIS_ENB | OTP_SW2_RDIS_ENB per option A1..A9 | Table 85 p79-80 | not exposed: fuse value, readable only through Snapshot (register loaded from this fuse) | model option table loads the value into the register at power-up; per-option test T19 | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OV-OTP_SW3_RDIS_ENB | OTP_SW3_RDIS_ENB per option A1..A9 | Table 85 p79-80 | not exposed: fuse value, readable only through Snapshot (register loaded from this fuse) | model option table loads the value into the register at power-up; per-option test T19 | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OV-OTP_SW1_DVSSPEED | OTP_SW1_DVSSPEED per option A1..A9 | Table 85 p79-80 | not exposed: fuse value, readable only through Snapshot (register loaded from this fuse) | model option table loads the value into the register at power-up; per-option test T19 | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OV-OTP_SW2_DVSSPEED | OTP_SW2_DVSSPEED per option A1..A9 | Table 85 p79-80 | not exposed: fuse value, readable only through Snapshot (register loaded from this fuse) | model option table loads the value into the register at power-up; per-option test T19 | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OV-OTP_SWx_EN_AND_STBY_EN | OTP_SWx_EN_AND_STBY_EN per option A1..A9 | Table 85 p79-80 | not exposed: fuse value, readable only through Snapshot (register loaded from this fuse) | model option table loads the value into the register at power-up; per-option test T19 | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OV-OTP_LDOx_EN_AND_STBY_EN | OTP_LDOx_EN_AND_STBY_EN per option A1..A9 | Table 85 p79-80 | not exposed: fuse value, readable only through Snapshot (register loaded from this fuse) | model option table loads the value into the register at power-up; per-option test T19 | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OV-OTP_PWRON_CFG | OTP_PWRON_CFG per option A1..A9 | Table 85 p79-80 | not exposed: fuse value, readable only through Snapshot (register loaded from this fuse) | model option table loads the value into the register at power-up; per-option test T19 | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OV-OTP_SEQ_CLK_SPEED | OTP_SEQ_CLK_SPEED per option A1..A9 | Table 85 p79-80 | StartupProfileOf(Option): order and slot time of options A1 to A9 (Table 85); the fuse itself is not readable | option table; the model runs the power-up sequence | T19: tests/test_lifecycle.cpp; tests/test_model.cpp | OK |
| OV-OTP_TGRESET10 | OTP_TGRESET[1:0] per option A1..A9 | Table 85 p79-80 | not exposed: fuse value, readable only through Snapshot (register loaded from this fuse) | model option table loads the value into the register at power-up; per-option test T19 | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OV-OTP_POR_DLY20 | OTP_POR_DLY[2:0] per option A1..A9 | Table 85 p79-80 | not exposed: fuse value, readable only through Snapshot (register loaded from this fuse) | model option table loads the value into the register at power-up; per-option test T19 | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OV-OTP_UVDET10 | OTP_UVDET[1:0] per option A1..A9 | Table 85 p79-80 | not exposed: fuse value, readable only through Snapshot (register loaded from this fuse) | model option table loads the value into the register at power-up; per-option test T19 | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OV-OTP_I2C_DEGLITCH_EN | OTP_I2C_DEGLITCH_EN per option A1..A9 | Table 85 p79-80 | not exposed: fuse value, readable only through Snapshot (register loaded from this fuse) | model option table loads the value into the register at power-up; per-option test T19 | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OV-OTP_CHGR_OPER10 | OTP_CHGR_OPER[1:0] per option A1..A9 | Table 85 p79-80 | not exposed: fuse value, readable only through Snapshot (register loaded from this fuse) | model option table loads the value into the register at power-up; per-option test T19 | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OV-OTP_CHGR_TPRECHG | OTP_CHGR_TPRECHG per option A1..A9 | Table 85 p79-80 | not exposed: fuse value, readable only through Snapshot (register loaded from this fuse) | model option table loads the value into the register at power-up; per-option test T19 | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OV-OTP_CHGR_EOCTIME20 | OTP_CHGR_EOCTIME[2:0] per option A1..A9 | Table 85 p79-80 | not exposed: fuse value, readable only through Snapshot (register loaded from this fuse) | model option table loads the value into the register at power-up; per-option test T19 | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OV-OTP_CHGR_FCHGTIME20 | OTP_CHGR_FCHGTIME[2:0] per option A1..A9 | Table 85 p79-80 | not exposed: fuse value, readable only through Snapshot (register loaded from this fuse) | model option table loads the value into the register at power-up; per-option test T19 | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OV-OTP_CHGR_EOC_MODE | OTP_CHGR_EOC_MODE per option A1..A9 | Table 85 p79-80 | not exposed: fuse value, readable only through Snapshot (register loaded from this fuse) | model option table loads the value into the register at power-up; per-option test T19 | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OV-OTP_CHGR_CHG_RESTART10 | OTP_CHGR_CHG_RESTART[1:0] per option A1..A9 | Table 85 p79-80 | not exposed: fuse value, readable only through Snapshot (register loaded from this fuse) | model option table loads the value into the register at power-up; per-option test T19 | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OV-OTP_CHGR_CHG_CC40 | OTP_CHGR_CHG_CC[4:0] per option A1..A9 | Table 85 p79-80 | not exposed: fuse value, readable only through Snapshot (register loaded from this fuse) | model option table loads the value into the register at power-up; per-option test T19 | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OV-OTP_CHGR_VSYSMIN10 | OTP_CHGR_VSYSMIN[1:0] per option A1..A9 | Table 85 p79-80 | not exposed: fuse value, readable only through Snapshot (register loaded from this fuse) | model option table loads the value into the register at power-up; per-option test T19 | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OV-OTP_CHGR_CHGCV50 | OTP_CHGR_CHGCV[5:0] per option A1..A9 | Table 85 p79-80 | not exposed: fuse value, readable only through Snapshot (register loaded from this fuse) | model option table loads the value into the register at power-up; per-option test T19 | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OV-OTP_CHGR_VBUS_LIN_ILIM40 | OTP_CHGR_VBUS_LIN_ILIM[4:0] per option A1..A9 | Table 85 p79-80 | not exposed: fuse value, readable only through Snapshot (register loaded from this fuse) | model option table loads the value into the register at power-up; per-option test T19 | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OV-OTP_CHGR_VBUS_DPM_REG20 | OTP_CHGR_VBUS_DPM_REG[2:0] per option A1..A9 | Table 85 p79-80 | not exposed: fuse value, readable only through Snapshot (register loaded from this fuse) | model option table loads the value into the register at power-up; per-option test T19 | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OV-OTP_CHGR_USBPHYLDO | OTP_CHGR_USBPHYLDO per option A1..A9 | Table 85 p79-80 | not exposed: fuse value, readable only through Snapshot (register loaded from this fuse) | model option table loads the value into the register at power-up; per-option test T19 | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OV-OTP_CHGR_USBPHY | OTP_CHGR_USBPHY per option A1..A9 | Table 85 p79-80 | not exposed: fuse value, readable only through Snapshot (register loaded from this fuse) | model option table loads the value into the register at power-up; per-option test T19 | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OV-OTP_CHGR_ACTDISPHY | OTP_CHGR_ACTDISPHY per option A1..A9 | Table 85 p79-80 | not exposed: fuse value, readable only through Snapshot (register loaded from this fuse) | model option table loads the value into the register at power-up; per-option test T19 | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
OTP image registers (T176)¶
| Id | Item | Datasheet | API | Model | Test | Status |
|---|---|---|---|---|---|---|
| OR-1C | OTP register 0x1C OTP_PMIC_CFG0: image byte per option A1..A9 | Table 176 p128-133 | not exposed: fuse image, no I2C window in Rev. 7; the loaded value is visible only through the PMIC/charger register it feeds | model option table holds the byte per option (data from T176) | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OR-1D | OTP register 0x1D OTP_SW1: image byte per option A1..A9 | Table 176 p128-133 | not exposed: fuse image, no I2C window in Rev. 7; the loaded value is visible only through the PMIC/charger register it feeds | model option table holds the byte per option (data from T176) | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OR-1E | OTP register 0x1E OTP_SW1_SW2: image byte per option A1..A9 | Table 176 p128-133 | not exposed: fuse image, no I2C window in Rev. 7; the loaded value is visible only through the PMIC/charger register it feeds | model option table holds the byte per option (data from T176) | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OR-1F | OTP register 0x1F OTP_SW2_SW3: image byte per option A1..A9 | Table 176 p128-133 | not exposed: fuse image, no I2C window in Rev. 7; the loaded value is visible only through the PMIC/charger register it feeds | model option table holds the byte per option (data from T176) | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OR-20 | OTP register 0x20 OTP_SW3_ILIM: image byte per option A1..A9 | Table 176 p128-133 | not exposed: fuse image, no I2C window in Rev. 7; the loaded value is visible only through the PMIC/charger register it feeds | model option table holds the byte per option (data from T176) | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OR-21 | OTP register 0x21 OTP_VREF_LDO1: image byte per option A1..A9 | Table 176 p128-133 | not exposed: fuse image, no I2C window in Rev. 7; the loaded value is visible only through the PMIC/charger register it feeds | model option table holds the byte per option (data from T176) | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OR-22 | OTP register 0x22 OTP_LDO1_LDO2: image byte per option A1..A9 | Table 176 p128-133 | not exposed: fuse image, no I2C window in Rev. 7; the loaded value is visible only through the PMIC/charger register it feeds | model option table holds the byte per option (data from T176) | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OR-23 | OTP register 0x23 OTP_LDO3: image byte per option A1..A9 | Table 176 p128-133 | not exposed: fuse image, no I2C window in Rev. 7; the loaded value is visible only through the PMIC/charger register it feeds | model option table holds the byte per option (data from T176) | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OR-24 | OTP register 0x24 OTP_PMIC_CFG1: image byte per option A1..A9 | Table 176 p128-133 | not exposed: fuse image, no I2C window in Rev. 7; the loaded value is visible only through the PMIC/charger register it feeds | model option table holds the byte per option (data from T176) | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OR-25 | OTP register 0x25 OTP_SW1_SW2_SEQ: image byte per option A1..A9 | Table 176 p128-133 | not exposed: fuse image, no I2C window in Rev. 7; the loaded value is visible only through the PMIC/charger register it feeds | model option table holds the byte per option (data from T176) | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OR-26 | OTP register 0x26 OTP_SW3_LDO1_SEQ: image byte per option A1..A9 | Table 176 p128-133 | not exposed: fuse image, no I2C window in Rev. 7; the loaded value is visible only through the PMIC/charger register it feeds | model option table holds the byte per option (data from T176) | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OR-27 | OTP register 0x27 OTP_LDO2_LDO3_SEQ: image byte per option A1..A9 | Table 176 p128-133 | not exposed: fuse image, no I2C window in Rev. 7; the loaded value is visible only through the PMIC/charger register it feeds | model option table holds the byte per option (data from T176) | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OR-28 | OTP register 0x28 OTP_PMIC_CFG2: image byte per option A1..A9 | Table 176 p128-133 | not exposed: fuse image, no I2C window in Rev. 7; the loaded value is visible only through the PMIC/charger register it feeds | model option table holds the byte per option (data from T176) | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OR-29 | OTP register 0x29 RSVD: image byte per option A1..A9 | Table 176 p128-133 | not exposed: reserved/spare/CRC byte | model option table holds the byte per option (data from T176) | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OR-2A | OTP register 0x2A RSVD: image byte per option A1..A9 | Table 176 p128-133 | not exposed: reserved/spare/CRC byte | model option table holds the byte per option (data from T176) | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OR-2B | OTP register 0x2B OTP_CHG_CFG0: image byte per option A1..A9 | Table 176 p128-133 | not exposed: fuse image, no I2C window in Rev. 7; the loaded value is visible only through the PMIC/charger register it feeds | model option table holds the byte per option (data from T176) | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OR-2C | OTP register 0x2C OTP_CHG_CFG1: image byte per option A1..A9 | Table 176 p128-133 | not exposed: fuse image, no I2C window in Rev. 7; the loaded value is visible only through the PMIC/charger register it feeds | model option table holds the byte per option (data from T176) | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OR-2D | OTP register 0x2D OTP_CHG_CFG2: image byte per option A1..A9 | Table 176 p128-133 | not exposed: fuse image, no I2C window in Rev. 7; the loaded value is visible only through the PMIC/charger register it feeds | model option table holds the byte per option (data from T176) | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OR-2E | OTP register 0x2E OTP_CHG_CFG3: image byte per option A1..A9 | Table 176 p128-133 | not exposed: fuse image, no I2C window in Rev. 7; the loaded value is visible only through the PMIC/charger register it feeds | model option table holds the byte per option (data from T176) | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OR-2F | OTP register 0x2F OTP_CHG_CFG4: image byte per option A1..A9 | Table 176 p128-133 | not exposed: fuse image, no I2C window in Rev. 7; the loaded value is visible only through the PMIC/charger register it feeds | model option table holds the byte per option (data from T176) | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OR-30 | OTP register 0x30 OTP_CHG_CFG5: image byte per option A1..A9 | Table 176 p128-133 | not exposed: fuse image, no I2C window in Rev. 7; the loaded value is visible only through the PMIC/charger register it feeds | model option table holds the byte per option (data from T176) | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OR-31 | OTP register 0x31 OTP_CHG_CFG6: image byte per option A1..A9 | Table 176 p128-133 | not exposed: fuse image, no I2C window in Rev. 7; the loaded value is visible only through the PMIC/charger register it feeds | model option table holds the byte per option (data from T176) | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OR-32 | OTP register 0x32 OTP_CHG_CFG7: image byte per option A1..A9 | Table 176 p128-133 | not exposed: fuse image, no I2C window in Rev. 7; the loaded value is visible only through the PMIC/charger register it feeds | model option table holds the byte per option (data from T176) | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OR-33 | OTP register 0x33 OTP_CHG_CFG8: image byte per option A1..A9 | Table 176 p128-133 | not exposed: fuse image, no I2C window in Rev. 7; the loaded value is visible only through the PMIC/charger register it feeds | model option table holds the byte per option (data from T176) | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OR-34 | OTP register 0x34 OTP_CHG_CFG9: image byte per option A1..A9 | Table 176 p128-133 | not exposed: fuse image, no I2C window in Rev. 7; the loaded value is visible only through the PMIC/charger register it feeds | model option table holds the byte per option (data from T176) | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OR-35 | OTP register 0x35 OTP_CHG_CFG10: image byte per option A1..A9 | Table 176 p128-133 | not exposed: fuse image, no I2C window in Rev. 7; the loaded value is visible only through the PMIC/charger register it feeds | model option table holds the byte per option (data from T176) | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OR-36 | OTP register 0x36 RSVD: image byte per option A1..A9 | Table 176 p128-133 | not exposed: reserved/spare/CRC byte | model option table holds the byte per option (data from T176) | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OR-37 | OTP register 0x37 OTP_CRC_LSB: image byte per option A1..A9 | Table 176 p128-133 | not exposed: reserved/spare/CRC byte | model option table holds the byte per option (data from T176) | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
OTP image fields (T176)¶
| Id | Item | Datasheet | API | Model | Test | Status |
|---|---|---|---|---|---|---|
| OF-1C.OTP_PWRGD_EN | OTP_PWRGD_EN (0x1C OTP_PMIC_CFG0) | Table 176 | not exposed: reserved, spare or no I2C-visible effect | stored as part of the option byte | T22: tests/test_irq.cpp | INFO |
| OF-1C.OTP_SEQ_CLK_SPEED | OTP_SEQ_CLK_SPEED (0x1C OTP_PMIC_CFG0) | Table 176 | StartupProfileOf(Option): order and slot time of options A1 to A9 (Table 85); the fuse itself is not readable | option table; the model runs the power-up sequence | T19: tests/test_lifecycle.cpp; tests/test_model.cpp | OK |
| OF-1C.OTP_PWRON_CFG | OTP_PWRON_CFG (0x1C OTP_PMIC_CFG0) | Table 176 | not exposed: fuse; effect visible through the PMIC/charger register it loads | option byte loaded into the register at power-up; per-option test | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OF-1C.UNUSED | UNUSED (0x1C OTP_PMIC_CFG0) | Table 176 | not exposed: reserved, spare or no I2C-visible effect | stored as part of the option byte | T22: tests/test_irq.cpp | INFO |
| OF-1D.OTP_SW1_DVSSPEED | OTP_SW1_DVSSPEED (0x1D OTP_SW1) | Table 176 | not exposed: fuse; effect visible through the PMIC/charger register it loads | option byte loaded into the register at power-up; per-option test | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OF-1D.OTP_SW1_RDIS_ENB | OTP_SW1_RDIS_ENB (0x1D OTP_SW1) | Table 176 | not exposed: fuse; effect visible through the PMIC/charger register it loads | option byte loaded into the register at power-up; per-option test | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OF-1D.OTP_SW1_VOLT50 | OTP_SW1_VOLT[5:0] (0x1D OTP_SW1) | Table 176 | not exposed: fuse; effect visible through the PMIC/charger register it loads | option byte loaded into the register at power-up; per-option test | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OF-1E.OTP_SW2_VOLT50 | OTP_SW2_VOLT[5:0] (0x1E OTP_SW1_SW2) | Table 176 | not exposed: fuse; effect visible through the PMIC/charger register it loads | option byte loaded into the register at power-up; per-option test | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OF-1E.OTP_SW1_DVS_SEL | OTP_SW1_DVS_SEL (0x1E OTP_SW1_SW2) | Table 176 | not exposed: fuse; effect visible through the PMIC/charger register it loads | option byte loaded into the register at power-up; per-option test | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OF-1E.OTP_SW1_EN_AND_STBY_EN | OTP_SW1_EN_AND_STBY_EN (0x1E OTP_SW1_SW2) | Table 176 | not exposed: fuse; effect visible through the PMIC/charger register it loads | option byte loaded into the register at power-up; per-option test | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OF-1F.OTP_SW3_VOLT30 | OTP_SW3_VOLT[3:0] (0x1F OTP_SW2_SW3) | Table 176 | not exposed: fuse; effect visible through the PMIC/charger register it loads | option byte loaded into the register at power-up; per-option test | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OF-1F.OTP_SW2_DVS_SEL | OTP_SW2_DVS_SEL (0x1F OTP_SW2_SW3) | Table 176 | not exposed: fuse; effect visible through the PMIC/charger register it loads | option byte loaded into the register at power-up; per-option test | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OF-1F.OTP_SW2_EN_AND_STBY_EN | OTP_SW2_EN_AND_STBY_EN (0x1F OTP_SW2_SW3) | Table 176 | not exposed: fuse; effect visible through the PMIC/charger register it loads | option byte loaded into the register at power-up; per-option test | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OF-1F.OTP_SW2_DVSSPEED | OTP_SW2_DVSSPEED (0x1F OTP_SW2_SW3) | Table 176 | not exposed: fuse; effect visible through the PMIC/charger register it loads | option byte loaded into the register at power-up; per-option test | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OF-1F.OTP_SW2_RDIS_ENB | OTP_SW2_RDIS_ENB (0x1F OTP_SW2_SW3) | Table 176 | not exposed: fuse; effect visible through the PMIC/charger register it loads | option byte loaded into the register at power-up; per-option test | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OF-20.OTP_SW3_ILIM10 | OTP_SW3_ILIM[1:0] (0x20 OTP_SW3_ILIM) | Table 176 | not exposed: fuse; effect visible through the PMIC/charger register it loads | option byte loaded into the register at power-up; per-option test | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OF-20.OTP_SW2_ILIM10 | OTP_SW2_ILIM[1:0] (0x20 OTP_SW3_ILIM) | Table 176 | not exposed: fuse; effect visible through the PMIC/charger register it loads | option byte loaded into the register at power-up; per-option test | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OF-20.OTP_SW1_ILIM10 | OTP_SW1_ILIM[1:0] (0x20 OTP_SW3_ILIM) | Table 176 | not exposed: fuse; effect visible through the PMIC/charger register it loads | option byte loaded into the register at power-up; per-option test | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OF-20.OTP_SW3_EN_AND_STBY_EN | OTP_SW3_EN_AND_STBY_EN (0x20 OTP_SW3_ILIM) | Table 176 | not exposed: fuse; effect visible through the PMIC/charger register it loads | option byte loaded into the register at power-up; per-option test | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OF-20.OTP_SW3_RDIS_ENB | OTP_SW3_RDIS_ENB (0x20 OTP_SW3_ILIM) | Table 176 | not exposed: fuse; effect visible through the PMIC/charger register it loads | option byte loaded into the register at power-up; per-option test | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OF-21.OTP_VREFDDR_EN_AND_STBY_EN | OTP_VREFDDR_EN_AND_STBY_EN (0x21 OTP_VREF_LDO1) | Table 176 | not exposed: fuse; effect visible through the PMIC/charger register it loads | option byte loaded into the register at power-up; per-option test | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OF-21.OTP_LDO1_LS_EN | OTP_LDO1_LS_EN (0x21 OTP_VREF_LDO1) | Table 176 | not exposed: fuse; effect visible through the PMIC/charger register it loads | option byte loaded into the register at power-up; per-option test | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OF-21.OTP_LDO1_VOLT40 | OTP_LDO1_VOLT[4:0] (0x21 OTP_VREF_LDO1) | Table 176 | not exposed: fuse; effect visible through the PMIC/charger register it loads | option byte loaded into the register at power-up; per-option test | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OF-21.UNUSED | UNUSED (0x21 OTP_VREF_LDO1) | Table 176 | not exposed: reserved, spare or no I2C-visible effect | stored as part of the option byte | T22: tests/test_irq.cpp | INFO |
| OF-22.OTP_LDO1_EN_AND_STBY_EN | OTP_LDO1_EN_AND_STBY_EN (0x22 OTP_LDO1_LDO2) | Table 176 | not exposed: fuse; effect visible through the PMIC/charger register it loads | option byte loaded into the register at power-up; per-option test | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OF-22.OTP_LDO2_EN_AND_STBY_EN | OTP_LDO2_EN_AND_STBY_EN (0x22 OTP_LDO1_LDO2) | Table 176 | not exposed: fuse; effect visible through the PMIC/charger register it loads | option byte loaded into the register at power-up; per-option test | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OF-22.OTP_LDO2_VOLT30 | OTP_LDO2_VOLT[3:0] (0x22 OTP_LDO1_LDO2) | Table 176 | not exposed: fuse; effect visible through the PMIC/charger register it loads | option byte loaded into the register at power-up; per-option test | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OF-22.UNUSED | UNUSED (0x22 OTP_LDO1_LDO2) | Table 176 | not exposed: reserved, spare or no I2C-visible effect | stored as part of the option byte | T22: tests/test_irq.cpp | INFO |
| OF-23.OTP_LDO3_EN_AND_STBY_EN | OTP_LDO3_EN_AND_STBY_EN (0x23 OTP_LDO3) | Table 176 | not exposed: fuse; effect visible through the PMIC/charger register it loads | option byte loaded into the register at power-up; per-option test | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OF-23.OTP_LDO3_LS_EN | OTP_LDO3_LS_EN (0x23 OTP_LDO3) | Table 176 | not exposed: fuse; effect visible through the PMIC/charger register it loads | option byte loaded into the register at power-up; per-option test | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OF-23.OTP_LDO3_VOLT40 | OTP_LDO3_VOLT[4:0] (0x23 OTP_LDO3) | Table 176 | not exposed: fuse; effect visible through the PMIC/charger register it loads | option byte loaded into the register at power-up; per-option test | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OF-23.UNUSED | UNUSED (0x23 OTP_LDO3) | Table 176 | not exposed: reserved, spare or no I2C-visible effect | stored as part of the option byte | T22: tests/test_irq.cpp | INFO |
| OF-24.OTP_UVDET10 | OTP_UVDET[1:0] (0x24 OTP_PMIC_CFG1) | Table 176 | not exposed: fuse; effect visible through the PMIC/charger register it loads | option byte loaded into the register at power-up; per-option test | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OF-24.OTP_POR_DLY20 | OTP_POR_DLY[2:0] (0x24 OTP_PMIC_CFG1) | Table 176 | not exposed: fuse; effect visible through the PMIC/charger register it loads | option byte loaded into the register at power-up; per-option test | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OF-24.OTP_TGRESET10 | OTP_TGRESET[1:0] (0x24 OTP_PMIC_CFG1) | Table 176 | not exposed: fuse; effect visible through the PMIC/charger register it loads | option byte loaded into the register at power-up; per-option test | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OF-24.UNUSED | UNUSED (0x24 OTP_PMIC_CFG1) | Table 176 | not exposed: reserved, spare or no I2C-visible effect | stored as part of the option byte | T22: tests/test_irq.cpp | INFO |
| OF-25.OTP_SW1_PWRUP_SEQ20 | OTP_SW1_PWRUP_SEQ[2:0] (0x25 OTP_SW1_SW2_SEQ) | Table 176 | StartupProfileOf(Option): order and slot time of options A1 to A9 (Table 85); the fuse itself is not readable | option table; the model runs the power-up sequence | T19: tests/test_lifecycle.cpp; tests/test_model.cpp | OK |
| OF-25.OTP_SW2_PWRUP_SEQ20 | OTP_SW2_PWRUP_SEQ[2:0] (0x25 OTP_SW1_SW2_SEQ) | Table 176 | StartupProfileOf(Option): order and slot time of options A1 to A9 (Table 85); the fuse itself is not readable | option table; the model runs the power-up sequence | T19: tests/test_lifecycle.cpp; tests/test_model.cpp | OK |
| OF-26.OTP_SW3_PWRUP_SEQ20 | OTP_SW3_PWRUP_SEQ[2:0] (0x26 OTP_SW3_LDO1_SEQ) | Table 176 | StartupProfileOf(Option): order and slot time of options A1 to A9 (Table 85); the fuse itself is not readable | option table; the model runs the power-up sequence | T19: tests/test_lifecycle.cpp; tests/test_model.cpp | OK |
| OF-26.OTP_LDO1_PWRUP_SEQ20 | OTP_LDO1_PWRUP_SEQ[2:0] (0x26 OTP_SW3_LDO1_SEQ) | Table 176 | StartupProfileOf(Option): order and slot time of options A1 to A9 (Table 85); the fuse itself is not readable | option table; the model runs the power-up sequence | T19: tests/test_lifecycle.cpp; tests/test_model.cpp | OK |
| OF-27.OTP_LDO2_PWRUP_SEQ20 | OTP_LDO2_PWRUP_SEQ[2:0] (0x27 OTP_LDO2_LDO3_SEQ) | Table 176 | StartupProfileOf(Option): order and slot time of options A1 to A9 (Table 85); the fuse itself is not readable | option table; the model runs the power-up sequence | T19: tests/test_lifecycle.cpp; tests/test_model.cpp | OK |
| OF-27.OTP_LDO3_PWRUP_SEQ20 | OTP_LDO3_PWRUP_SEQ[2:0] (0x27 OTP_LDO2_LDO3_SEQ) | Table 176 | StartupProfileOf(Option): order and slot time of options A1 to A9 (Table 85); the fuse itself is not readable | option table; the model runs the power-up sequence | T19: tests/test_lifecycle.cpp; tests/test_model.cpp | OK |
| OF-28.OTP_SHIP_COREOFF_CYA | OTP_SHIP_COREOFF_CYA (0x28 OTP_PMIC_CFG2) | Table 176 | not exposed: reserved, spare or no I2C-visible effect | stored as part of the option byte | T22: tests/test_irq.cpp | INFO |
| OF-28.OTP_I2C_SLV_ADDR20 | OTP_I2C_SLV_ADDR[2:0] (0x28 OTP_PMIC_CFG2) | Table 176 | not exposed: fuse; effect visible through the PMIC/charger register it loads | option byte loaded into the register at power-up; per-option test | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OF-28.OTP_I2C_DEGLITCH_EN | OTP_I2C_DEGLITCH_EN (0x28 OTP_PMIC_CFG2) | Table 176 | not exposed: fuse; effect visible through the PMIC/charger register it loads | option byte loaded into the register at power-up; per-option test | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OF-28.OTP_VREFDDR_PWRUP_SEQ20 | OTP_VREFDDR_PWRUP_SEQ[2:0] (0x28 OTP_PMIC_CFG2) | Table 176 | StartupProfileOf(Option): order and slot time of options A1 to A9 (Table 85); the fuse itself is not readable | option table; the model runs the power-up sequence | T19: tests/test_lifecycle.cpp; tests/test_model.cpp | OK |
| OF-29.ReservedOTP_VSNVS_VOLT20 | Reserved(OTP_VSNVS_VOLT[2:0]) (0x29 RSVD) | Table 176 | not exposed: reserved, spare or no I2C-visible effect | stored as part of the option byte | T22: tests/test_irq.cpp | INFO |
| OF-29.ReservedOTP_FORCE_LICELL | Reserved(OTP_FORCE_LICELL) (0x29 RSVD) | Table 176 | not exposed: reserved, spare or no I2C-visible effect | stored as part of the option byte | T22: tests/test_irq.cpp | INFO |
| OF-29.UNUSED | UNUSED (0x29 RSVD) | Table 176 | not exposed: reserved, spare or no I2C-visible effect | stored as part of the option byte | T22: tests/test_irq.cpp | INFO |
| OF-2A.OTP_PMIC_SPARE070 | OTP_PMIC_SPARE0[7:0] (0x2A RSVD) | Table 176 | not exposed: reserved, spare or no I2C-visible effect | stored as part of the option byte | T22: tests/test_irq.cpp | INFO |
| OF-2B.OTP_CHGR_EOCTIME20 | OTP_CHGR_EOCTIME[2:0] (0x2B OTP_CHG_CFG0) | Table 176 | not exposed: fuse; effect visible through the PMIC/charger register it loads | option byte loaded into the register at power-up; per-option test | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OF-2B.OTP_CHGR_OPER10 | OTP_CHGR_OPER[1:0] (0x2B OTP_CHG_CFG0) | Table 176 | not exposed: fuse; effect visible through the PMIC/charger register it loads | option byte loaded into the register at power-up; per-option test | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OF-2B.OTP_CHGR_TPRECHG | OTP_CHGR_TPRECHG (0x2B OTP_CHG_CFG0) | Table 176 | not exposed: fuse; effect visible through the PMIC/charger register it loads | option byte loaded into the register at power-up; per-option test | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OF-2B.ReservedOTP_CHGR_THM_WARM | Reserved(OTP_CHGR_THM_WARM) (0x2B OTP_CHG_CFG0) | Table 176 | not exposed: reserved, spare or no I2C-visible effect | stored as part of the option byte | T22: tests/test_irq.cpp | INFO |
| OF-2B.ReservedOTP_CHGR_THM_COOL | Reserved(OTP_CHGR_THM_COOL) (0x2B OTP_CHG_CFG0) | Table 176 | not exposed: reserved, spare or no I2C-visible effect | stored as part of the option byte | T22: tests/test_irq.cpp | INFO |
| OF-2C.OTP_CHGR_CHG_RESTART10 | OTP_CHGR_CHG_RESTART[1:0] (0x2C OTP_CHG_CFG1) | Table 176 | not exposed: fuse; effect visible through the PMIC/charger register it loads | option byte loaded into the register at power-up; per-option test | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OF-2C.OTP_CHGR_FCHGTIME20 | OTP_CHGR_FCHGTIME[2:0] (0x2C OTP_CHG_CFG1) | Table 176 | not exposed: fuse; effect visible through the PMIC/charger register it loads | option byte loaded into the register at power-up; per-option test | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OF-2C.ReservedOTP_CHGR_EOC_EXIT | Reserved(OTP_CHGR_EOC_EXIT) (0x2C OTP_CHG_CFG1) | Table 176 | not exposed: reserved, spare or no I2C-visible effect | stored as part of the option byte | T22: tests/test_irq.cpp | INFO |
| OF-2C.ReservedOTP_CHGR_EOC_MODE | Reserved(OTP_CHGR_EOC_MODE) (0x2C OTP_CHG_CFG1) | Table 176 | not exposed: reserved, spare or no I2C-visible effect | stored as part of the option byte | T22: tests/test_irq.cpp | INFO |
| OF-2C.ReservedOTP_CHGR_FORCE_BATT_ISO | Reserved(OTP_CHGR_FORCE_BATT_ISO) (0x2C OTP_CHG_CFG1) | Table 176 | not exposed: reserved, spare or no I2C-visible effect | stored as part of the option byte | T22: tests/test_irq.cpp | INFO |
| OF-2D.OTP_CHGR_VSYSMIN10 | OTP_CHGR_VSYSMIN[1:0] (0x2D OTP_CHG_CFG2) | Table 176 | not exposed: fuse; effect visible through the PMIC/charger register it loads | option byte loaded into the register at power-up; per-option test | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OF-2D.OTP_CHGR_CHG_CC40 | OTP_CHGR_CHG_CC[4:0] (0x2D OTP_CHG_CFG2) | Table 176 | not exposed: fuse; effect visible through the PMIC/charger register it loads | option byte loaded into the register at power-up; per-option test | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OF-2D.OTP_CHGR_TEMPFB_EN | OTP_CHGR_TEMPFB_EN (0x2D OTP_CHG_CFG2) | Table 176 | not exposed: fuse; effect visible through the PMIC/charger register it loads | option byte loaded into the register at power-up; per-option test | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OF-2E.OTP_CHGR_BATFET_OC10 | OTP_CHGR_BATFET_OC[1:0] (0x2E OTP_CHG_CFG3) | Table 176 | not exposed: fuse; effect visible through the PMIC/charger register it loads | option byte loaded into the register at power-up; per-option test | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OF-2E.OTP_CHGR_CHGCV50 | OTP_CHGR_CHGCV[5:0] (0x2E OTP_CHG_CFG3) | Table 176 | not exposed: fuse; effect visible through the PMIC/charger register it loads | option byte loaded into the register at power-up; per-option test | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OF-2F.OTP_CHGR_THM_CNFG10 | OTP_CHGR_THM_CNFG[1:0] (0x2F OTP_CHG_CFG4) | Table 176 | not exposed: fuse; effect visible through the PMIC/charger register it loads | option byte loaded into the register at power-up; per-option test | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OF-2F.OTP_CHGR_REGTEMP10 | OTP_CHGR_REGTEMP[1:0] (0x2F OTP_CHG_CFG4) | Table 176 | not exposed: fuse; effect visible through the PMIC/charger register it loads | option byte loaded into the register at power-up; per-option test | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OF-2F.OTP_CHGR_THM_COLD | OTP_CHGR_THM_COLD (0x2F OTP_CHG_CFG4) | Table 176 | not exposed: fuse; effect visible through the PMIC/charger register it loads | option byte loaded into the register at power-up; per-option test | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OF-2F.OTP_CHGR_THM_HOT | OTP_CHGR_THM_HOT (0x2F OTP_CHG_CFG4) | Table 176 | not exposed: fuse; effect visible through the PMIC/charger register it loads | option byte loaded into the register at power-up; per-option test | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OF-2F.OTP_CHGR_BOVRC_DISBATFET | OTP_CHGR_BOVRC_DISBATFET (0x2F OTP_CHG_CFG4) | Table 176 | not exposed: fuse; effect visible through the PMIC/charger register it loads | option byte loaded into the register at power-up; per-option test | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OF-2F.UNUSED | UNUSED (0x2F OTP_CHG_CFG4) | Table 176 | not exposed: reserved, spare or no I2C-visible effect | stored as part of the option byte | T22: tests/test_irq.cpp | INFO |
| OF-30.OTP_CHGR_VBUS_LIN_ILIM40 | OTP_CHGR_VBUS_LIN_ILIM[4:0] (0x30 OTP_CHG_CFG5) | Table 176 | not exposed: fuse; effect visible through the PMIC/charger register it loads | option byte loaded into the register at power-up; per-option test | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OF-30.OTP_CHGR_VIN_DPM_STOP | OTP_CHGR_VIN_DPM_STOP (0x30 OTP_CHG_CFG5) | Table 176 | not exposed: fuse; effect visible through the PMIC/charger register it loads | option byte loaded into the register at power-up; per-option test | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OF-30.UNUSED | UNUSED (0x30 OTP_CHG_CFG5) | Table 176 | not exposed: reserved, spare or no I2C-visible effect | stored as part of the option byte | T22: tests/test_irq.cpp | INFO |
| OF-31.OTP_CHGR_SYS_WKUP_DLY10 | OTP_CHGR_SYS_WKUP_DLY[1:0] (0x31 OTP_CHG_CFG6) | Table 176 | not exposed: fuse; effect visible through the PMIC/charger register it loads | option byte loaded into the register at power-up; per-option test | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OF-31.OTP_CHGR_VBUS_DPM_REG20 | OTP_CHGR_VBUS_DPM_REG[2:0] (0x31 OTP_CHG_CFG6) | Table 176 | not exposed: fuse; effect visible through the PMIC/charger register it loads | option byte loaded into the register at power-up; per-option test | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OF-31.OTP_CHGR_ACTDISPHY | OTP_CHGR_ACTDISPHY (0x31 OTP_CHG_CFG6) | Table 176 | not exposed: fuse; effect visible through the PMIC/charger register it loads | option byte loaded into the register at power-up; per-option test | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OF-31.OTP_CHGR_USBPHY | OTP_CHGR_USBPHY (0x31 OTP_CHG_CFG6) | Table 176 | not exposed: fuse; effect visible through the PMIC/charger register it loads | option byte loaded into the register at power-up; per-option test | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OF-31.OTP_CHGR_USBPHYLDO | OTP_CHGR_USBPHYLDO (0x31 OTP_CHG_CFG6) | Table 176 | not exposed: fuse; effect visible through the PMIC/charger register it loads | option byte loaded into the register at power-up; per-option test | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OF-32.OTP_CHGR_CC_ADJ10 | OTP_CHGR_CC_ADJ[1:0] (0x32 OTP_CHG_CFG7) | Table 176 | not exposed: fuse; effect visible through the PMIC/charger register it loads | option byte loaded into the register at power-up; per-option test | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OF-32.OTP_CHGR_VBUS_OV_TDB10 | OTP_CHGR_VBUS_OV_TDB[1:0] (0x32 OTP_CHG_CFG7) | Table 176 | not exposed: fuse; effect visible through the PMIC/charger register it loads | option byte loaded into the register at power-up; per-option test | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OF-32.OTP_CHGR_CHG_INT_EN | OTP_CHGR_CHG_INT_EN (0x32 OTP_CHG_CFG7) | Table 176 | not exposed: fuse; effect visible through the PMIC/charger register it loads | option byte loaded into the register at power-up; per-option test | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OF-32.OTP_CHGR_EOC_INT | OTP_CHGR_EOC_INT (0x32 OTP_CHG_CFG7) | Table 176 | not exposed: fuse; effect visible through the PMIC/charger register it loads | option byte loaded into the register at power-up; per-option test | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OF-32.ReservedOTP_CHGR_USB_PHY_TDB10 | Reserved(OTP_CHGR_USB_PHY_TDB[1:0]) (0x32 OTP_CHG_CFG7) | Table 176 | not exposed: reserved, spare or no I2C-visible effect | stored as part of the option byte | T22: tests/test_irq.cpp | INFO |
| OF-33.OTP_CHGR_LED_CURRENT10 | OTP_CHGR_LED_CURRENT[1:0] (0x33 OTP_CHG_CFG8) | Table 176 | not exposed: fuse; effect visible through the PMIC/charger register it loads | option byte loaded into the register at power-up; per-option test | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OF-33.OTP_CHGR_VBUS2SYS_TDB10 | OTP_CHGR_VBUS2SYS_TDB[1:0] (0x33 OTP_CHG_CFG8) | Table 176 | not exposed: fuse; effect visible through the PMIC/charger register it loads | option byte loaded into the register at power-up; per-option test | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OF-33.OTP_CHGR_VBUS2SYS_THRSH | OTP_CHGR_VBUS2SYS_THRSH (0x33 OTP_CHG_CFG8) | Table 176 | not exposed: fuse; effect visible through the PMIC/charger register it loads | option byte loaded into the register at power-up; per-option test | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OF-33.OTP_CHGR_CV_ADJ10 | OTP_CHGR_CV_ADJ[1:0] (0x33 OTP_CHG_CFG8) | Table 176 | not exposed: fuse; effect visible through the PMIC/charger register it loads | option byte loaded into the register at power-up; per-option test | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OF-33.UNUSED | UNUSED (0x33 OTP_CHG_CFG8) | Table 176 | not exposed: reserved, spare or no I2C-visible effect | stored as part of the option byte | T22: tests/test_irq.cpp | INFO |
| OF-34.OTP_CHGR_LED_CNFG | OTP_CHGR_LED_CNFG (0x34 OTP_CHG_CFG9) | Table 176 | not exposed: fuse; effect visible through the PMIC/charger register it loads | option byte loaded into the register at power-up; per-option test | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OF-34.OTP_CHGR_OVFLT_BFET_EN | OTP_CHGR_OVFLT_BFET_EN (0x34 OTP_CHG_CFG9) | Table 176 | not exposed: fuse; effect visible through the PMIC/charger register it loads | option byte loaded into the register at power-up; per-option test | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OF-34.OTP_CHGR_WDFLT_BFET_EN | OTP_CHGR_WDFLT_BFET_EN (0x34 OTP_CHG_CFG9) | Table 176 | not exposed: fuse; effect visible through the PMIC/charger register it loads | option byte loaded into the register at power-up; per-option test | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OF-34.OTP_CHGR_THMSUS_BFET_EN | OTP_CHGR_THMSUS_BFET_EN (0x34 OTP_CHG_CFG9) | Table 176 | not exposed: fuse; effect visible through the PMIC/charger register it loads | option byte loaded into the register at power-up; per-option test | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OF-34.OTP_CHGR_TSHDN_BFET_EN | OTP_CHGR_TSHDN_BFET_EN (0x34 OTP_CHG_CFG9) | Table 176 | not exposed: fuse; effect visible through the PMIC/charger register it loads | option byte loaded into the register at power-up; per-option test | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OF-34.OTP_CHGR_TMRFLT_BFET_EN | OTP_CHGR_TMRFLT_BFET_EN (0x34 OTP_CHG_CFG9) | Table 176 | not exposed: fuse; effect visible through the PMIC/charger register it loads | option byte loaded into the register at power-up; per-option test | T19,T22: tests/test_lifecycle.cpp; tests/test_model.cpp; tests/test_irq.cpp | OK |
| OF-34.ReservedOTP_CHGR_BETA_SEL10 | Reserved(OTP_CHGR_BETA_SEL[1:0]) (0x34 OTP_CHG_CFG9) | Table 176 | not exposed: reserved, spare or no I2C-visible effect | stored as part of the option byte | T22: tests/test_irq.cpp | INFO |
| OF-35.ReservedOTP_CHGR_PRECHG_LOWBATT_THRSH10 | Reserved(OTP_CHGR_PRECHG_LOWBATT_THRSH[1:0]) (0x35 OTP_CHG_CFG10) | Table 176 | not exposed: reserved, spare or no I2C-visible effect | stored as part of the option byte | T22: tests/test_irq.cpp | INFO |
| OF-35.ReservedOTP_CHGR_FET_SCALE | Reserved(OTP_CHGR_FET_SCALE) (0x35 OTP_CHG_CFG10) | Table 176 | not exposed: reserved, spare or no I2C-visible effect | stored as part of the option byte | T22: tests/test_irq.cpp | INFO |
| OF-35.UNUSED | UNUSED (0x35 OTP_CHG_CFG10) | Table 176 | not exposed: reserved, spare or no I2C-visible effect | stored as part of the option byte | T22: tests/test_irq.cpp | INFO |
| OF-36.OTP_CHGR_SPARE070 | OTP_CHGR_SPARE0[7:0] (0x36 RSVD) | Table 176 | not exposed: reserved, spare or no I2C-visible effect | stored as part of the option byte | T22: tests/test_irq.cpp | INFO |
| OF-37.CRC1LSB | CRC[1]LSB (0x37 OTP_CRC_LSB) | Table 176 | not exposed: reserved, spare or no I2C-visible effect | stored as part of the option byte | T22: tests/test_irq.cpp | INFO |
| OF-RB | OTP read-back window (undocumented, dropped) [TODO: needs the NXP document] | not in Rev. 7 | not exposed in v1 (owner decision) | not modelled | TODO | TODO |
Functional-chapter tables (T27 to T72)¶
| Id | Item | Datasheet | API | Model | Test | Status |
|---|---|---|---|---|---|---|
| FN-T27 | T27 Voltage regulators summary | Table 27 p24 | decided at REG-32..REG-65, SW grids (T01), LDO grids (T01) | model per the referenced rows | T14: tests/test_rails.cpp; tests/test_configure.cpp | OK |
| FN-T28 | T28 SWx DVS setting selection | Table 28 p26 | decided at FLD-1E, Config.dvs (C1) | model per the referenced rows | T14: tests/test_rails.cpp; tests/test_configure.cpp | OK |
| FN-T29 | T29 Buck operating modes | Table 29 p27 | decided at FLD-35.SW1_FPWM/LPWR | model per the referenced rows | T14: tests/test_rails.cpp; tests/test_configure.cpp | OK |
| FN-T30 | T30 Buck mode control | Table 30 p28 | decided at FLD-35/3B bits; model enable table | model per the referenced rows | T14,T06: tests/test_rails.cpp; tests/test_configure.cpp | OK |
| FN-T31 | T31 SW1/SW2 voltage tables | Table 31 p29 | decided at SW grids (T01); FLD-32/33/34 | model per the referenced rows | T01,T14: tests/test_config.cpp; inc/pf1550_codec.hpp (static_assert); tests/test_rails.cpp; tests/test_configure.cpp | OK |
| FN-T32 | T32 Inductance and capacitance values | Table 32 p31 | not applicable: board BOM, hardware page | not modelled | N/A: no driver decision | INFO |
| FN-T33 | T33 Inductor part numbers | Table 33 p31 | not applicable: board BOM | not modelled | N/A: no driver decision | INFO |
| FN-T34 | T34 Capacitor part numbers | Table 34 p31 | not applicable: board BOM | not modelled | N/A: no driver decision | INFO |
| FN-T35 | T35 SW3 operating modes | Table 35 p32 | decided at FLD-41 bits | model per the referenced rows | T14: tests/test_rails.cpp; tests/test_configure.cpp | OK |
| FN-T36 | T36 SW3 mode control | Table 36 p32 | decided at FLD-41; model enable table | model per the referenced rows | T14,T06: tests/test_rails.cpp; tests/test_configure.cpp | OK |
| FN-T37 | T37 SW3 voltage table | Table 37 p33 | decided at SW grids (T01); FLD-3E..40 | model per the referenced rows | T01,T14: tests/test_config.cpp; inc/pf1550_codec.hpp (static_assert); tests/test_rails.cpp; tests/test_configure.cpp | OK |
| FN-T38 | T38 SW3 inductance/capacitance | Table 38 p34 | not applicable: board BOM | not modelled | N/A: no driver decision | INFO |
| FN-T39 | T39 SW3 inductor parts | Table 39 p34 | not applicable: board BOM | not modelled | N/A: no driver decision | INFO |
| FN-T40 | T40 SW3 capacitor parts | Table 40 p34 | not applicable: board BOM | not modelled | N/A: no driver decision | INFO |
| FN-T41 | T41 LDO1/LDO3 voltage table | Table 41 p36 | decided at LDO grids (T01); FLD-4C/52 | model per the referenced rows | T01,T14: tests/test_config.cpp; inc/pf1550_codec.hpp (static_assert); tests/test_rails.cpp; tests/test_configure.cpp | OK |
| FN-T42 | T42 LDOy control bits | Table 42 p37 | decided at FLD-4D/53 | model per the referenced rows | T14,T16: tests/test_rails.cpp; tests/test_configure.cpp; tests/test_power.cpp; tests/test_review.cpp | OK |
| FN-T43 | T43 LDO2 voltage table | Table 43 p39 | decided at LDO grids (T01); FLD-4F | model per the referenced rows | T01,T14: tests/test_config.cpp; inc/pf1550_codec.hpp (static_assert); tests/test_rails.cpp; tests/test_configure.cpp | OK |
| FN-T44 | T44 LDO2 control bits | Table 44 p40 | decided at FLD-50 | model per the referenced rows | T14: tests/test_rails.cpp; tests/test_configure.cpp | OK |
| FN-T45 | T45 Battery regulation voltage register (copy of T160) | Table 45 p44 | decided at REG-8F; reset 0x2B agrees | model per the referenced rows | T01: tests/test_config.cpp; inc/pf1550_codec.hpp (static_assert) | OK |
| FN-T46 | T46 VSYSMIN setting | Table 46 p45 | decided at FLD-8F.VSYSMIN | model per the referenced rows | T01,T07: tests/test_config.cpp; inc/pf1550_codec.hpp (static_assert); tests/test_charger.cpp | OK |
| FN-T47 | T47 Charger current control register (copy of T159) | Table 47 p48 | decided at REG-8E; reset 0x2B agrees | model per the referenced rows | T01: tests/test_config.cpp; inc/pf1550_codec.hpp (static_assert) | OK |
| FN-T48 | T48 Constant current charge settings | Table 48 p48 | decided at FLD-8E.CHG_CC; EL-T10-IFC | model per the referenced rows | T01,T02: tests/test_config.cpp; inc/pf1550_codec.hpp (static_assert); tests/test_review.cpp | OK |
| FN-T49 | T49 Battery regulation voltage register (copy) | Table 49 p50 | decided at REG-8F | model per the referenced rows | T01: tests/test_config.cpp; inc/pf1550_codec.hpp (static_assert) | OK |
| FN-T50 | T50 CV settings | Table 50 p50 | decided at FLD-8F.CHGCV; EL-T10-VCHGCV_RANGE | model per the referenced rows | T01,T02: tests/test_config.cpp; inc/pf1550_codec.hpp (static_assert); tests/test_review.cpp | OK |
| FN-T51 | T51 Charger timers register (copy of T157) | Table 51 p52 | decided at REG-8A; reset 0x0A agrees | model per the referenced rows | T09: tests/test_charger.cpp | OK |
| FN-T52 | T52 Fast charge timer settings | Table 52 p52 | decided at FLD-8A.FCHGTIME | model per the referenced rows | T09: tests/test_charger.cpp | OK |
| FN-T53 | T53 Charger EOC register (copy of T158) | Table 53 p53 | decided at REG-8D | model per the referenced rows | T07: tests/test_charger.cpp | OK |
| FN-T54 | T54 EOC current thresholds | Table 54 p53 | decided at FLD-8D.IEOC | model per the referenced rows | T01,T07: tests/test_config.cpp; inc/pf1550_codec.hpp (static_assert); tests/test_charger.cpp | OK |
| FN-T55 | T55 Charger timers register (copy) | Table 55 p54 | decided at REG-8A | model per the referenced rows | T09: tests/test_charger.cpp | OK |
| FN-T56 | T56 EOC state timer settings | Table 56 p54 | decided at FLD-8A.EOCTIME | model per the referenced rows | T09: tests/test_charger.cpp | OK |
| FN-T57 | T57 VBUS input current limit register (copy of T163) | Table 57 p56 | decided at REG-94; reset 0x68 agrees | model per the referenced rows | T01: tests/test_config.cpp; inc/pf1550_codec.hpp (static_assert) | OK |
| FN-T58 | T58 Input current limit settings | Table 58 p56 | decided at FLD-94.VBUS_LIN_ILIM | model per the referenced rows | T01,T11: tests/test_config.cpp; inc/pf1550_codec.hpp (static_assert); tests/test_charger.cpp | OK |
| FN-T59 | T59 Thermal regulation | Table 59 p57 | decided at FLD-92 fields; EL-T15-TREG | model per the referenced rows | T10: tests/test_configure.cpp; tests/test_charger.cpp | OK |
| FN-T60 | T60 Temperature regulation control register (copy of T162) | Table 60 p59 | decided at REG-92 | model per the referenced rows | T10: tests/test_configure.cpp; tests/test_charger.cpp | OK |
| FN-T61 | T61 Thermal regulation settings | Table 61 p59 | decided at FLD-92.REGTEMP | model per the referenced rows | T10: tests/test_configure.cpp; tests/test_charger.cpp | OK |
| FN-T62 | T62 VBUS linear dynamic input voltage register (copy of T164) | Table 62 p61 | decided at REG-95; shows 0x00 = 3.9 V (C24) | model per the referenced rows | T11: tests/test_charger.cpp | OK |
| FN-T63 | T63 Input voltage regulation thresholds | Table 63 p61 | decided at FLD-95.VBUS_DPM_REG | model per the referenced rows | T01,T11: tests/test_config.cpp; inc/pf1550_codec.hpp (static_assert); tests/test_charger.cpp | OK |
| FN-T64 | T64 JEITA thermal control | Table 64 p62 | decided at FLD-92.THM_CNFG, FLD-9A | model per the referenced rows | T10: tests/test_configure.cpp; tests/test_charger.cpp | OK |
| FN-T65 | T65 Temperature regulation control register (copy) | Table 65 p62 | decided at REG-92 | model per the referenced rows | T10: tests/test_configure.cpp; tests/test_charger.cpp | OK |
| FN-T66 | T66 JEITA temperature control register (copy of T168) | Table 66 p63 | decided at REG-9A | model per the referenced rows | T10: tests/test_configure.cpp; tests/test_charger.cpp | OK |
| FN-T67 | T67 CV voltage adjustment settings | Table 67 p64 | decided at FLD-9A.CV_ADJ | model per the referenced rows | T10: tests/test_configure.cpp; tests/test_charger.cpp | OK |
| FN-T68 | T68 CC current adjustment settings | Table 68 p64 | decided at FLD-9A.CC_ADJ | model per the referenced rows | T10: tests/test_configure.cpp; tests/test_charger.cpp | OK |
| FN-T69 | T69 Battery overcurrent thresholds | Table 69 p66 | decided at FLD-91.BATFET_OC; EL-T14-IBOVCR | model per the referenced rows | T08: tests/test_charger.cpp | OK |
| FN-T70 | T70 LED modes | Table 70 p67 | decided at FLD-9E.LED_CFG | model per the referenced rows | T17: tests/test_configure.cpp | OK |
| FN-T71 | T71 LED enable conditions | Table 71 p67 | decided at FLD-9C.LED_EN, FLD-9E.LEDOVRD | model per the referenced rows | T17: tests/test_configure.cpp | OK |
| FN-T72 | T72 LED frequency setting | Table 72 p68 | decided at FLD-9E.LED_FREQ | model per the referenced rows | T17: tests/test_configure.cpp | OK |