Skip to content

Hardware

The TLE92466ED's pins, bus settings, timing and power, as the driver uses them. Section numbers refer to the datasheet, Rev. 1.2.

Datasheet sections this page relies on

From Infineon IFX-ntz1491827137291 1.2:

  • Pins, RESN, EN, DRV0/DRV1 and FAULTN: 2 Pin configuration; 4.2.3 TDS_I/O Pins, p. 7
  • Functional range of VDD, VBAT, VIO, f_SYS and f_PWM: 3.2.1 Functional range, Table 6, p. 11
  • Supplies, VIO_SEL and the power-on reset: 4.1.1 TDS_Power Supply, p. 14
  • Reset times t_RESN and t_POR: 4.1.3 Electrical characteristics power supply, Table 9, p. 15
  • Clock source, PLL dividers and INIT_DONE: 4.2.1 TDS_Clock; Equations 2, 3; Table 10, p. 16
  • Direct drive via SPI on-time and DRV pins: 4.8.1 TDS_Direct Drive; Equation 10, p. 32
  • SPI frame, mode and CRC-8 SAE J1850: 5.1.1 TDS_General information; 5.1.2 TDS_Cyclic redundancy check (CRC), p. 47
  • SPI timing: 5.1.4 Electrical characteristics SPI interface, Table 18, p. 48
  • Identity, ICVID and CHIPID: 5.3.2.19 Version Register; 5.3.2.24 Unique Chip Identification Number Register 0, p. 75
  • Application circuit: 6.1 TDS_Application information; Figure 26, p. 105

All of them, with the driver API for each: Datasheet map.

Pins

The PG-DSO-36 package from the top (section 2, Figure 2 and Table 1), with the cooling tab underneath.

Pinout of the TLE92466ED in PG-DSO-36, top view: 36 pins and an exposed pad, each with its name, its electrical type as a colour and the driver hook that uses it.Pinout of the TLE92466ED in PG-DSO-36, top view: 36 pins and an exposed pad, each with its name, its electrical type as a colour and the driver hook that uses it.
TLE92466ED pinout, PG-DSO-36
Figure description and sources

The TLE92466ED seen from the top, in its PG-DSO-36 package. Pin 1 is marked by the dot; the numbers run counter-clockwise from it. Each pad is coloured by the pin's electrical type (legend below). Next to it is the pin's name and, in mono, the hook of the driver's port that drives or reads it; a pin without a hook is not used by the driver. The dashed square is the exposed pad.

Drawn from: docs/hardware.yml; inc/tle92466ed_spi_interface.hpp.

PG-DSO-36, 36 pins and an exposed pad (2 Pin configuration, Figure 2, p. 7).

Pin Name Type (domain) Function Driver hook If unused Datasheet
1 LOAD0 power output (VBAT) Low-side output, channel 0 - Leave open 2, p. 7
2 FWD0 analog (VBAT) Freewheeling diode of channel 0 - Leave open 2, p. 7
3 GNDP0 ground Power-stage ground, channel 0 - - 2, p. 7
4 GND ground Signal ground; connected to the cooling tab - - 2, p. 7
5 CSN bus (VIO) SPI chip select, active low; internal pull-up Transfer() - 2, p. 7
6 SCK bus (VIO) SPI clock, up to 8 MHz; internal pull-down Transfer() - 5.1.4, p. 48
7 SI bus (VIO) SPI data in (MOSI); internal pull-down Transfer() - 2, p. 7
8 VIO power (VIO) Supply of SO, 3.3 V or 5 V (3.0 V to 5.5 V) - - 3.2.1, p. 11
9 SO bus (VIO) SPI data out (MISO), push-pull from VIO Transfer() - 2, p. 7
10 GND ground Signal ground; connected to the cooling tab - - 2, p. 7
11 FAULTN open drain (VIO) Fault output, low on a critical fault, RESN low or an unmasked fault GpioRead(CtrlPin::Fault) Leave open 4.2.3, p. 17
12 GND ground Signal ground; connected to the cooling tab - - 2, p. 7
13 LOAD5 power output (VBAT) Low-side output, channel 5 - Leave open 2, p. 7
14 FWD5 analog (VBAT) Freewheeling diode of channel 5 - Leave open 2, p. 7
15 GNDP5 ground Power-stage ground, channel 5 - - 2, p. 7
16 GNDP1 ground Power-stage ground, channel 1 - - 2, p. 7
17 FWD1 analog (VBAT) Freewheeling diode of channel 1 - Leave open 2, p. 7
18 LOAD1 power output (VBAT) Low-side output, channel 1 - Leave open 2, p. 8
19 LOAD2 power output (VBAT) Low-side output, channel 2 - Leave open 2, p. 8
20 FWD2 analog (VBAT) Freewheeling diode of channel 2 - Leave open 2, p. 8
21 GNDP2 ground Power-stage ground, channel 2 - - 2, p. 8
22 VBAT power (VBAT) Battery supply through reverse protection and filter, 6 V to 18 V - - 3.2.1, p. 11
23 GND ground Signal ground; connected to the cooling tab - - 2, p. 8
24 CLK digital in (VIO) External clock, 1 MHz to 8 MHz; internal pull-down - Connect to GND 4.2.3, p. 17
25 DRV0 digital in (VIO) Direct-drive input 0; internal pull-down GpioSet(CtrlPin::Drv0) Connect to GND 4.2.3, p. 17
26 RESN digital in (VIO) Reset, active low; internal pull-down GpioSet(CtrlPin::Reset) - 4.2.3, p. 17
27 EN digital in (VIO) Enable, active high: low turns every channel off; internal pull-down GpioSet(CtrlPin::Enable) - 4.2.3, p. 17
28 DRV1 digital in (VIO) Direct-drive input 1; internal pull-down GpioSet(CtrlPin::Drv1) Connect to GND 4.2.3, p. 17
29 VDD power (VDD) 5 V supply of the digital circuits (4.5 V to 5.5 V) - - 3.2.1, p. 11
30 GND ground Signal ground; connected to the cooling tab - - 2, p. 8
31 LOAD4 power output (VBAT) Low-side output, channel 4 - Leave open 2, p. 8
32 FWD4 analog (VBAT) Freewheeling diode of channel 4 - Leave open 2, p. 8
33 GNDP4 ground Power-stage ground, channel 4 - - 2, p. 8
34 GNDP3 ground Power-stage ground, channel 3 - - 2, p. 8
35 FWD3 analog (VBAT) Freewheeling diode of channel 3 - Leave open 2, p. 8
36 LOAD3 power output (VBAT) Low-side output, channel 3 - Leave open 2, p. 8
EP TAB ground Cooling tab; connect to GND and the heat sink area - - 2, p. 8

Source of this table and of the chip figures: docs/hardware.yml.

The five GND pins and the tab are the signal ground; each channel's power stage has its own GNDPx, which connects to the same ground. Set Config::vio to the VIO level (the MCU's I/O supply). CLK is the external PLL clock, 1 MHz to 8 MHz; with the internal oscillator, tie it to GND. The pinout, the block diagram, the circuit and both tables are drawn from docs/hardware.yml.

Inside the chip

Section 1, Figure 1: the central logic takes the control pins and the SPI registers and runs six identical channels, each with its own channel logic, current control and dither, diagnosis, current sense, overcurrent and temperature protection, and a low-side DMOS with its shunt. The power supply block reports undervoltage and overvoltage to the central logic; the PLL makes the system clock f_SYS.

Block diagram of the TLE92466ED: its function blocks, how they connect and which package pins reach each block.Block diagram of the TLE92466ED: its function blocks, how they connect and which package pins reach each block.
Inside the TLE92466ED
Figure description and sources

The TLE92466ED's function blocks inside its outline. Arrows between blocks carry signals or data in the direction they point (both ways where they have two heads). The package pins stand on the left and right edges with their numbers, each wired to the block it reaches.

Drawn from: docs/hardware.yml; inc/tle92466ed_spi_interface.hpp.

Control pins

The driver drives RESN, EN, DRV0 and DRV1 only through the optional GpioSet() hook of your port, with logical levels (GpioSignal::ACTIVE on RESN means "in reset", which your port writes as a low level), and reads FAULTN through the optional GpioRead() hook. Their idle levels, which your port drives before it enables each output:

Pin Idle level Why
RESN Low, ACTIVE (in reset) Every register at its reset value and every channel off until the driver starts the chip
EN Low, INACTIVE Every channel off; the driver raises it in EnterMissionMode() and lowers it in EnterConfigMode()
DRV0, DRV1 Low, INACTIVE A direct-drive channel stays off until the application drives the pin
CSN High The SPI driver's job; the chip ignores the bus while CSN is high

Without GpioSet(), tie RESN and EN high (through a resistor) and DRVx low: EnsureInitialized() then waits t_POR instead of pulsing RESN and writes every register, since the chip may keep what an earlier run wrote, and HardwareReset() and SetDrivePin() return Error::Unsupported.

Bus settings

Setting Value (sections 5.1, 5.2; Table 18) Driver constant
SPI mode 1: SCK idles low, SO changes on the rising edge, SI is sampled on the falling edge kSpiMode
Clock Up to 8 MHz kMaxClockHz
Bit order MSB first on SI and SO kMsbFirst
Frame 32 bits in one CSN low period; any other length is ignored kFrameBytes
CSN high between frames At least 600 ns (t_CSN_TD) kMinCsHighNs
CSN to SCK, SCK to CSN At least 250 ns (t_CSN_LEAD, t_CSN_LAG) kCsSetupNs, kCsHoldNs

Every frame carries a CRC-8 SAE J1850 (polynomial 0x1D, initial value 0xFF, final XOR 0xFF) in bits 31..24, computed over bits 7..0, 15..8 and 23..16 in that order (section 5.1.2). The chip answers each frame during the next one (section 5.2.1):

sequenceDiagram
    participant Host
    participant TLE92466ED
    Host->>TLE92466ED: frame 1: read FB_DC of CH0 (0x0240)
    TLE92466ED-->>Host: reply to the previous frame
    Host->>TLE92466ED: frame 2: anchor read of ICVID (0x0200)
    TLE92466ED-->>Host: FB_DC, 22-bit reply
Frame Bits 31..24 23..17 16 15..0
Write (5.2.3.1) CRC 7-bit address 1 Data
Read (5.2.3.2) CRC Don't care (sent as 1100000B) 0 16-bit address
16-bit reply (5.2.3.3) CRC Reply mode 00, 5-bit status R/W echo Data
22-bit reply (5.2.3.4) CRC Reply mode 01, data 21..16 Data 16 Data
Critical fault frame (5.2.3.5) Don't care Reply mode 10 Don't care Bits 7..0: supply and clock flags

Architecture shows how the driver checks each reply.

Timing

Parameter Symbol Value Driver
Logic ready after RESN released t_RESN 0.1 ms maximum (Table 9) kResetReleaseUs, then INIT_DONE polled
Logic ready after a power-on reset t_POR 10 ms maximum (Table 9) kPowerOnResetUs, waited when the port has no GpioSet()
RESN low pulse none Not specified: 1 ms is the design value kResetPulseUs (not verified on hardware)
INIT_DONE after a reset or a clock change none Not specified Polled every kPollIntervalUs for Config::init_timeout_us
SPI watchdog count f_SPI,WD f_SYS / 2^14, 0.585 ms per count at 28 MHz WatchdogReloadCode(), at most 2047 counts (1.198 s)
Overcurrent shutdown t_OC,DETECT 1.5 µs maximum The chip's own

Power and supervision

Supply Range (Table 6) Monitored (section 4.1.2)
VDD 4.5 V to 5.5 V; SPI works from 3.5 V UV 3.7 V to 4.5 V, OV 5.5 V to 6.4 V
VIO 3.0 V to 5.5 V Against the 3.3 V or the 5 V thresholds that VIO_SEL selects
VBAT 6 V to 18 V (4 V to 38 V with deviations) Config::vbat_uv_code and vbat_ov_code, 162 mV per count

A VDD or VIO fault ends Mission Mode and clears every EN_CH; a VBAT fault is reported only. With VIO_SEL on the wrong level (the reset value is 5 V), a 3.3 V VIO reads as undervoltage and EnterMissionMode() returns MissionBlocked. VDD draws up to 40 mA; VBAT up to 1 mA in normal mode and 10 µA with VDD and VIO off (Table 9).

Application circuit

Section 6.1, Figure 26, with all six channels drawn: 100 µF and 100 nF on VBAT, 100 nF on VDD and on VIO at the pins, 4.7 nF to 10 nF from each LOAD and FWD pin to ground, a freewheeling diode from each FWDx to the load supply, and 10 kΩ from FAULTN to VIO. Each load connects between the load supply (behind a high-side safety switch, with 100 nF on it) and its LOADx pin. Figure 26 also ties RESN and EN to the reset and watchdog outputs of the system's power-supply chip; here the MCU drives them through GpioSet(), as the driver expects.

Schematic of the TLE92466ED simplified application circuit: the chip with U2 MCU, C1 polarized-capacitor 100 µF, C2 capacitor 100 nF, C3 capacitor 100 nF, C4 capacitor 100 nF, C5 capacitor 100 nF, R1 resistor 10 kΩ, L0 solenoid, L1 solenoid, L2 solenoid, L3 solenoid, L4 solenoid, L5 solenoid, D0 diode, D1 diode, D2 diode, D3 diode, D4 diode, D5 diode, C10 capacitor 4.7 nF to 10 nF, C11 capacitor 4.7 nF to 10 nF, C12 capacitor 4.7 nF to 10 nF, C13 capacitor 4.7 nF to 10 nF, C14 capacitor 4.7 nF to 10 nF, C15 capacitor 4.7 nF to 10 nF, C20 capacitor 4.7 nF to 10 nF, C21 capacitor 4.7 nF to 10 nF, C22 capacitor 4.7 nF to 10 nF, C23 capacitor 4.7 nF to 10 nF, C24 capacitor 4.7 nF to 10 nF, C25 capacitor 4.7 nF to 10 nF; the MCU wires carry the port hooks GpioRead(CtrlPin::Fault), GpioSet(CtrlPin::Drv0), GpioSet(CtrlPin::Drv1), GpioSet(CtrlPin::Enable), GpioSet(CtrlPin::Reset), Transfer().Schematic of the TLE92466ED simplified application circuit: the chip with U2 MCU, C1 polarized-capacitor 100 µF, C2 capacitor 100 nF, C3 capacitor 100 nF, C4 capacitor 100 nF, C5 capacitor 100 nF, R1 resistor 10 kΩ, L0 solenoid, L1 solenoid, L2 solenoid, L3 solenoid, L4 solenoid, L5 solenoid, D0 diode, D1 diode, D2 diode, D3 diode, D4 diode, D5 diode, C10 capacitor 4.7 nF to 10 nF, C11 capacitor 4.7 nF to 10 nF, C12 capacitor 4.7 nF to 10 nF, C13 capacitor 4.7 nF to 10 nF, C14 capacitor 4.7 nF to 10 nF, C15 capacitor 4.7 nF to 10 nF, C20 capacitor 4.7 nF to 10 nF, C21 capacitor 4.7 nF to 10 nF, C22 capacitor 4.7 nF to 10 nF, C23 capacitor 4.7 nF to 10 nF, C24 capacitor 4.7 nF to 10 nF, C25 capacitor 4.7 nF to 10 nF; the MCU wires carry the port hooks GpioRead(CtrlPin::Fault), GpioSet(CtrlPin::Drv0), GpioSet(CtrlPin::Drv1), GpioSet(CtrlPin::Enable), GpioSet(CtrlPin::Reset), Transfer().
TLE92466ED: Simplified application circuit
Figure description and sources

A schematic. The MCU is on the left, each of its pins level with the chip pin it connects to; above each wire is the hook of the driver's port that drives or reads it. Supply pins point up to their supply and decoupling, ground pins down. Pins on the right carry the loads and the pins tied to a supply or ground; a cross marks a pin left open. A dot is a junction; wires that cross without a dot are not connected.

Drawn from: docs/hardware.yml; inc/tle92466ed_spi_interface.hpp.

Part Kind Value Connects Datasheet
U2 MCU - VDD: VIO, GND: GND, SCK: SCK, MOSI: SI, MISO: SO, CS: CSN, RST: RESN, EN: EN, FLT: FAULTN, D0: DRV0, D1: DRV1, CLKO: CLK 6.1, p. 105
C1 polarized capacitor 100 µF VBAT, GND 6.1, p. 105
C2 capacitor 100 nF VBAT, GND 6.1, p. 105
C3 capacitor 100 nF +5V, GND 6.1, p. 105
C4 capacitor 100 nF VIO, GND 6.1, p. 105
C5 capacitor 100 nF VBAT_SW, GND 6.1, p. 105
R1 resistor 10 kΩ VIO, FAULTN 6.1, p. 105
L0 solenoid - VBAT_SW, LOAD0 6.1, p. 105
L1 solenoid - VBAT_SW, LOAD1 6.1, p. 105
L2 solenoid - VBAT_SW, LOAD2 6.1, p. 105
L3 solenoid - VBAT_SW, LOAD3 6.1, p. 105
L4 solenoid - VBAT_SW, LOAD4 6.1, p. 105
L5 solenoid - VBAT_SW, LOAD5 6.1, p. 105
D0 diode - VBAT_SW, FWD0 6.1, p. 105
D1 diode - VBAT_SW, FWD1 6.1, p. 105
D2 diode - VBAT_SW, FWD2 6.1, p. 105
D3 diode - VBAT_SW, FWD3 6.1, p. 105
D4 diode - VBAT_SW, FWD4 6.1, p. 105
D5 diode - VBAT_SW, FWD5 6.1, p. 105
C10 capacitor 4.7 nF to 10 nF GND, LOAD0 6.1, p. 105
C11 capacitor 4.7 nF to 10 nF GND, LOAD1 6.1, p. 105
C12 capacitor 4.7 nF to 10 nF GND, LOAD2 6.1, p. 105
C13 capacitor 4.7 nF to 10 nF GND, LOAD3 6.1, p. 105
C14 capacitor 4.7 nF to 10 nF GND, LOAD4 6.1, p. 105
C15 capacitor 4.7 nF to 10 nF GND, LOAD5 6.1, p. 105
C20 capacitor 4.7 nF to 10 nF GND, FWD0 6.1, p. 105
C21 capacitor 4.7 nF to 10 nF GND, FWD1 6.1, p. 105
C22 capacitor 4.7 nF to 10 nF GND, FWD2 6.1, p. 105
C23 capacitor 4.7 nF to 10 nF GND, FWD3 6.1, p. 105
C24 capacitor 4.7 nF to 10 nF GND, FWD4 6.1, p. 105
C25 capacitor 4.7 nF to 10 nF GND, FWD5 6.1, p. 105

Export a circuit for a schematic or PCB tool: kokeb-docs hardware --kicad-netlist OUT.net --circuit typical.

Design decisions and bench steps

The datasheet is silent on these; the driver's choice and the step that confirms it on a bench:

What Driver's choice Bench step
RESN low time kResetPulseUs = 1 ms Scope RESN and SO: after the pulse and t_RESN the first FB_STAT reads INIT_DONE = 1
CSN timing of the port The ESP32 port runs 2 MHz so half a clock covers t_CSN_LEAD Scope CSN and SCK: lead and lag at least 250 ns, CSN high at least 600 ns
The don't-care bits of a read frame Sent as 1100000B Read ICVID at 1 MHz: 0xC1FC or 0xC1FE with status 0

Status and limitations lists every step still to run.

Reference documents

Every pin, setting and timing on this page cites a section of the datasheet; its revision, its SHA-256 and the sections each page relies on are in docs/datasheets.yml.

Document Revision Get it
Datasheet: TLE92466ED (Infineon IFX-ntz1491827137291) 1.2, 2022-02-01 PDF · vendor page

Written against these revisions; the SHA-256 of each file is in docs/datasheets.yml. Where each part of the driver is in the datasheet: Datasheet map.

Also useful Contents
inc/tle92466ed_registers.hpp The register map as the driver uses it, with datasheet section numbers
inc/tle92466ed_spi_interface.hpp The bus requirements and the frame codec