Datasheet map¶
The driver follows the BNO08X datasheet. This page says which revision, where to get it, and where each part of the driver is described in it, so you can check any behaviour against the source. Section names and page numbers are the datasheet's own (the printed page numbers).
- Datasheet: BNO080/BNO085/BNO086 data sheet, CEVA 1000-3927, revision 1.17 (2023-07-24). Get it from the vendor
page or as a
PDF.
SHA-256 of the file used:
34ac0ca1dda8fb0ecf347b35042bb32d22c953b127a0e414852213edc2c502ca. - Datasheet: BNO080/BNO085 data sheet (earlier revision, history only), CEVA 1000-3927, revision 1.8 (2020-02-05).
Get it from the vendor page or as a
PDF.
SHA-256 of the file used:
f671e7282db5ca019906f77e07e8fe5682f3c65b392f01a19fbf923abeed9ce2. - Datasheet: BNO080 data sheet (earliest revision), CEVA (Hillcrest Labs) 1000-3927, revision 1.3 (2017-10-01). Get
it from the vendor page or as a
PDF.
SHA-256 of the file used:
f32c45e136faa5ac6fd08e23697cf5fe292a3d9fbe0877fa745ae020212960a5. - Datasheet companion, reference manual: SH-2 Reference Manual, CEVA 1000-3625, revision 1.9 (2021-06-10). Get it
from the vendor page or as a
PDF.
SHA-256 of the file used:
dfa74afa12177982428574ef6a60df0009f32ff8ea339e44db37442e9066b984. - Datasheet companion, reference manual: SH-2 Reference Manual (earlier revision, history only), CEVA (Hillcrest
Labs) 1000-3625, revision 1.2 (2017-05-19). Get it from the vendor
page or as a
PDF.
SHA-256 of the file used:
d8da934e9a8c3a1dad5859f59a6c58ee7d03198fb0991ef54fc2065700ac9514. - Datasheet companion, protocol: Sensor Hub Transport Protocol (SHTP), CEVA 1000-3535, revision 1.10 (2021-06-10).
Get it from the vendor page or as a
PDF.
SHA-256 of the file used:
528b04ae7a0908a038234e10f0194393cc4fb96d658a617696dc74f6e6b298b6. - Datasheet companion, protocol: SH-2 SHTP Reference Manual, CEVA 1000-3600, revision 1.6 (2019-01-01). Get it from
the vendor page or as a
PDF.
SHA-256 of the file used:
3a5accc0659b173654d49a8cb91cd123db52cc08f72313cf25592f310d90a553. - Datasheet companion, application note: BNO080/BNO085 calibration guide, CEVA 1000-4044, revision 1.6 (2023-02-01).
Get it from the vendor page
or as a PDF.
SHA-256 of the file used:
bbfdac37b0de057fbbfac78ae10d1c9e65c2b1eb4147978838848661a078516e. - Datasheet companion, application note: BNO080/BNO085 calibration procedure (earlier revision), CEVA 1000-4044,
revision 1.3 (2019-07-01). Get it from the vendor
page or as a
PDF.
SHA-256 of the file used:
a1606e5efd799dabb2e234c0f6e895c4a831dbfaced1dc21647b90851a9f4b55. - Datasheet companion, application note: BNO085/BNO086 tare usage guide, CEVA 1000-4045, revision 1.3 (2023-02-01).
Get it from the vendor page or
as a PDF.
SHA-256 of the file used:
481d144d8bc63419f89e37a07ac989f668cc2c65523b7a71a2268cd216b0a0ba. - Datasheet companion, application note: BNO080/BNO085 migration guide (from the BNO070), CEVA (Hillcrest Labs) none
printed, revision 1.6 (2017-10-01). Get it from the vendor
page or as a
PDF.
SHA-256 of the file used:
4787168aa0158b99bfd2b0203ae57b042991d3e77fa454952f1363c18edddc31. - Datasheet: FSP200 data sheet (same SH-2, read for context only), CEVA 1000-4121, revision 1.5 (2022-09-01). Get it
from the vendor page or as a
PDF.
SHA-256 of the file used:
592875d802438360d9538e83a93c2023611fe45c77087c53e56b76a2d07c80a7. - Datasheet: BMF055 data sheet (same silicon; electrical limits cross-check only), Bosch Sensortec BST-BMF055-DS000,
revision 0.4 (2020-11-01). Get it from the vendor
page.
SHA-256 of the file used:
9447d15a9ee4237d60935e83cf206816e3ab82d5aa65047c574e45b595c79448. - Datasheet companion, application note: BNO055 handling, soldering and mounting instructions (mounting cross-check
only), Bosch Sensortec BST-BNO055-HS000, revision 1.0 (2015-01-01). Get it from the vendor
page.
SHA-256 of the file used:
ad153075fcd50f8bae9a34c5d37a9e9bb2431c5c29cf3e03d2b925372915e6f9.
| Topic | Datasheet section | Page | In the driver | Explained on |
|---|---|---|---|---|
| Features, variants and what differs | 1000-3927: Features (front page) | p. 1 | Variant, Config::variant, Config::strict_variant |
BNO08x Driver, Ambiguities and decisions, Hardware |
| Protocol selection (PS1, PS0) | 1000-3927: 1.2 BNO08X Connectivity | p. 9 | Transport, HubInterface::kTransport |
Hardware, Transports |
| Pins, straps and the clock source | 1000-3927: 1.2.1 Pin Descriptions | p. 10 | SetReset, SetBootn, IntAsserted, SetWake |
Hardware, Porting |
| I2C: address, clock stretching, framing | 1000-3927: 1.2.2 I2C interface | p. 12 | Transport::I2c, Config::i2c_address, I2cWrite, I2cRead |
Transports, Porting, Hardware |
| UART-SHTP: baud rate, framing, byte gap | 1000-3927: 1.2.3 UART-SHTP interface | p. 15 | Transport::UartShtp, UartRead, UartWriteByte |
Transports, Porting |
| SPI: mode, WAKE, H_INTN handshake | 1000-3927: 1.2.4 SPI Interface | p. 17 | Transport::Spi, SpiTransfer, SetWake, Config::wake_timeout_us |
Transports, Porting |
| UART-RVC: the 19-byte frame | 1000-3927: 1.2.5 UART-RVC interface | p. 20 | Transport::UartRvc, RvcFrame, EventKind::Rvc |
Transports |
| SHTP header, channels and cargo reads | 1000-3927: 1.3.1 SHTP | p. 22 | detail::RxEngine, Stats |
Transports, Architecture |
| Report structure, product ID, executable commands | 1000-3927: 1.3.2 Report Structure | p. 23 | ReadProductId(), Reset(), HubOn(), HubSleep() |
API guide, Architecture |
| Configuration and the commands list | 1000-3927: 1.3.3 BNO08X Configuration | p. 24 | SetFeature(), GetFeature(), the command operations |
API guide, Sensors |
| Sensor metadata and the FRS record list | 1000-3927: 1.3.4 Sensor Metadata | p. 25 | ReadMetadata(), ReadFrs(), Metadata |
Calibration and orientation |
| Sensor reports, timestamps and batching | 1000-3927: 1.3.5 Sensor Reports | p. 26 | Event, FeatureConfig::batch_us, Flush() |
Sensors |
| Motion, orientation and environmental outputs | 1000-3927: 2 Sensor data processing | p. 30 | SensorId, InDatasheet() |
Sensors, Ambiguities and decisions |
| Calibration and its accuracy | 1000-3927: 3.1 Calibration Effects | p. 37 | ConfigureMeCal(), Accuracy, SaveDcd() |
Calibration and orientation |
| Interactive calibration (BNO086 only) | 1000-3927: 3.3 Interactive Calibration (BNO086 only) | p. 39 | SetMotionIntent(), SensorId::MotionRequest |
Calibration and orientation, Ambiguities and decisions |
| Orientation and tare | 1000-3927: 4 BNO08X orientation | p. 40 | Tare(), SetReorientation() |
Calibration and orientation |
| Getting started: establishing contact and reading | 1000-3927: 5 Getting started with BNO08X | p. 43 | Begin(), Poll(), State |
Architecture, Quickstart |
| Supplies, absolute maximum ratings and power management | 1000-3927: 6.1 Absolute Maximum Electrical Ratings | p. 45 | - | Hardware |
| SPI timing | 1000-3927: 6.5.2 SPI timing | p. 46 | - | Transports |
| Start-up timing | 1000-3927: 6.5.3 Startup timing | p. 47 | HardReset(), Config::startup_timeout_ms |
Hardware, Architecture |
| Interrupt timing: host must answer H_INTN | 1000-3927: 6.5.4 Interrupt timing | p. 48 | Poll() guidance, Config::poll_interval_ms |
Transports, Troubleshooting |
| Report rates and latency | 1000-3927: 6.9 Report Rates | p. 50 | FeatureConfig::interval_us |
Sensors |
| Package outline and landing pattern | 1000-3927: 7.1 Package Outline | p. 53 | - | Hardware |
| Version history: BNO080 removed, polling note | 1000-3927: 8 Version history | p. 56 | Config::variant, Config::poll_without_int |
Ambiguities and decisions |
| UART inputs of the RVC mode | 1000-3625: 3.1.2 UART Inputs | p. 12 | RvcSend(), Config::rvc_inputs_experimental |
Transports, Ambiguities and decisions |
| Configuration records | 1000-3625: 4.3 Records | p. 14 | reg::kFrs*, ReadFrs(), WriteFrs() |
Calibration and orientation |
| Sensor metadata record layout | 1000-3625: 5.1 Sensor Metadata | p. 30 | Metadata, MetadataRecord() |
Calibration and orientation |
| Feature reports, rate and batch | 1000-3625: 5.4 Feature Reports | p. 34 | FeatureConfig, SetFeature() |
Sensors, API guide |
| Interactive calibration | 1000-3625: 5.6 Interactive Calibration | p. 36 | SetMotionIntent() |
Calibration and orientation |
| Product ID request and response | 1000-3625: 6.3.1 Product ID Request (0xF9) | p. 39 | ReadProductId(), ProductId |
API guide |
| FRS write and read | 1000-3625: 6.3.3 FRS Write Request (0xF7) | p. 40 | WriteFrs(), ReadFrs(), EraseFrs() |
Calibration and orientation |
| Command request and response | 1000-3625: 6.3.8 Command Request (0xF2) | p. 43 | detail::OpKind, onCommandResponse |
Architecture, API guide |
| Report errors, counters, initialise | 1000-3625: 6.4.1 Report Errors (0x01) | p. 45 | ReportErrors(), GetCounts(), ClearCounts(), Initialize() |
API guide |
| Tare now and persist tare | 1000-3625: 6.4.3 Tare (0x03) | p. 47 | Tare(), PersistTare(), SetReorientation() |
Calibration and orientation |
| Dynamic calibration data and ME calibration | 1000-3625: 6.4.5 Save DCD (0x06) | p. 51 | SaveDcd(), ConfigureMeCal(), GetMeCal(), SetPeriodicDcd() |
Calibration and orientation |
| Simple calibration, interactive calibration, wheel | 1000-3625: 6.4.10 Simple Calibration Commands (0x0C) | p. 55 | StartSimpleCal(), FinishSimpleCal(), SetMotionIntent(), SendWheel() |
Calibration and orientation, API guide |
| Sensor report common fields and status | 1000-3625: 6.5.1 Common Fields | p. 62 | Accuracy, Event::report_seq |
Sensors |
| Common dynamic feature report | 1000-3625: 6.5.2 Common Dynamic Feature Report | p. 63 | FeatureConfig |
Sensors |
| Batching and batch timestamps | 1000-3625: 7 Batching | p. 91 | Event::t_us, Config::strict_cont_len |
Sensors |
| Header, channels and the rules of a cargo | 1000-3535: 2.2.1 SHTP Header | p. 4 | detail::EncodeHeader, detail::RxEngine |
Transports, Architecture |
| Reading cargoes, continuations and interrupts | 1000-3535: 2.5 Reading Cargoes | p. 6 | Config::strict_cont_len, Stats::lost_cargo |
Transports |
| Synchronous protocols: I2C and SPI handshake | 1000-3535: 3 Synchronous protocols (SPI/I2C) | p. 7 | Transport::I2c, Transport::Spi |
Transports |
| SHTP over UART: control characters, BSQ and BSN | 1000-3535: 4 SHTP over UART | p. 10 | detail::UartFramer, Config::uart_token_timeout_ms |
Transports |
| Command channel and the error list | 1000-3535: 5.1 Command Channel | p. 13 | EventKind::HubError, Stats |
Transports, Troubleshooting |
| Channel advertisement | 1000-3535: 5.2 Channel Advertisement | p. 15 | detail::ParseAdvertisement |
Transports, Architecture |
| SH-2 channel usage and report lengths | 1000-3600: 2.2 SH-2 Channel Usage | p. 4 | detail::Advert, kReportLengths |
Transports, Sensors |
| Calibration procedure and user calibration | 1000-4044: 3.0 User Calibration | p. 5 | ConfigureMeCal(), SaveDcd() |
Calibration and orientation |
| Tare options and procedure | 1000-4045: Tare Overview | p. 1 | Tare(), AxisMask, TareBasis |
Calibration and orientation |
| Pin and interface differences from the BNO070 | none printed: 2.1 Pinout Comparisons | p. 7 | - | Hardware, Ambiguities and decisions |
When the datasheet and the driver differ¶
The driver is written against the revision above. If you have a newer revision, compare its revision history with the topics above; a change to a pin, a register, a timing or a value the driver uses is a bug report for this repository. Where the driver deliberately goes beyond the datasheet, the Contract says so.
The repository never contains the PDF itself: vendors own their documents. Download it from the vendor, and compare its SHA-256 with the one above to confirm you have the same file.