|
|
constexpr uint8_t | pca9685::reg::kMode1 = 0x00 |
| | MODE1 (R/W): restart, clock, AI, sleep, group calls.
|
| |
|
constexpr uint8_t | pca9685::reg::kMode2 = 0x01 |
| | MODE2 (R/W): output inversion, change, drive, OE.
|
| |
|
constexpr uint8_t | pca9685::reg::kSubAdr1 = 0x02 |
| | SUBADR1 (R/W): I2C subaddress 1 (section 7.3.6).
|
| |
|
constexpr uint8_t | pca9685::reg::kSubAdr2 = 0x03 |
| | SUBADR2 (R/W): I2C subaddress 2.
|
| |
|
constexpr uint8_t | pca9685::reg::kSubAdr3 = 0x04 |
| | SUBADR3 (R/W): I2C subaddress 3.
|
| |
|
constexpr uint8_t | pca9685::reg::kAllCallAdr = 0x05 |
| | ALLCALLADR (R/W): LED All Call address (7.3.7).
|
| |
|
constexpr uint8_t | pca9685::reg::kLed0OnL = 0x06 |
| | LED0_ON_L (R/W): first of 16 x 4 channel bytes.
|
| |
|
constexpr uint8_t | pca9685::reg::kLed15OffH = 0x45 |
| | LED15_OFF_H (R/W): the last channel byte.
|
| |
|
constexpr uint8_t | pca9685::reg::kAllLedOnL = 0xFA |
| | ALL_LED_ON_L (W): loads every LEDn_ON_L (7.3.4).
|
| |
|
constexpr uint8_t | pca9685::reg::kAllLedOffH = 0xFD |
| | ALL_LED_OFF_H (W): loads every LEDn_OFF_H.
|
| |
|
constexpr uint8_t | pca9685::reg::kPreScale = 0xFE |
| | PRE_SCALE (R/W): PWM frequency; written in SLEEP.
|
| |
|
constexpr uint8_t | pca9685::reg::kBytesPerChannel = 4 |
| | Bytes per channel: ON_L, ON_H, OFF_L, OFF_H (table 7).
|
| |
|
constexpr uint8_t | pca9685::reg::kChannels = 16 |
| | Number of LED channels.
|
| |
|
constexpr uint8_t | pca9685::reg::kSubAdrReadOnly = 0x01 |
| | SUBADR1 to 3 and ALLCALLADR bit 0: read only, reads 0 (tables 9, 10).
|
| |
|
constexpr uint8_t | pca9685::reg::kSubAdr1Reset = 0xE2 |
| | SUBADR1 after a reset (table 9).
|
| |
| constexpr uint8_t | pca9685::reg::kMode1Restart = 1U << 7 |
| |
|
constexpr uint8_t | pca9685::reg::kMode1ExtClk = 1U << 6 |
| | EXTCLK: use the EXTCLK pin; sticky.
|
| |
|
constexpr uint8_t | pca9685::reg::kMode1Ai = 1U << 5 |
| | AI: register auto-increment.
|
| |
|
constexpr uint8_t | pca9685::reg::kMode1Sleep = 1U << 4 |
| | SLEEP: oscillator off, low-power mode.
|
| |
|
constexpr uint8_t | pca9685::reg::kMode1Sub1 = 1U << 3 |
| | SUB1: answer I2C subaddress 1.
|
| |
|
constexpr uint8_t | pca9685::reg::kMode1Sub2 = 1U << 2 |
| | SUB2: answer I2C subaddress 2.
|
| |
|
constexpr uint8_t | pca9685::reg::kMode1Sub3 = 1U << 1 |
| | SUB3: answer I2C subaddress 3.
|
| |
| constexpr uint8_t | pca9685::reg::kMode1AllCall = 1U << 0 |
| |
|
constexpr uint8_t | pca9685::reg::kMode1Reset = 0x11 |
| | MODE1 after a power-on or software reset: SLEEP and ALLCALL set (table 5).
|
| |
|
constexpr uint8_t | pca9685::reg::kMode2Reserved = 0xE0 |
| | Bits 7..5: reserved, read only, read 0.
|
| |
|
constexpr uint8_t | pca9685::reg::kMode2Invrt = 1U << 4 |
| | INVRT: output logic inverted (OE = 0 only).
|
| |
|
constexpr uint8_t | pca9685::reg::kMode2Och = 1U << 3 |
| | OCH: outputs change on ACK, not on STOP.
|
| |
| constexpr uint8_t | pca9685::reg::kMode2OutDrv = 1U << 2 |
| |
|
constexpr uint8_t | pca9685::reg::kMode2Reset = 0x04 |
| | MODE2 after a reset: change on STOP, totem pole, not inverted, LEDn = 0 when OE = 1.
|
| |
|
constexpr uint32_t | pca9685::reg::kOutneLow = 0U |
| | OUTNE = 00: LEDn = 0.
|
| |
| constexpr uint32_t | pca9685::reg::kOutneHigh |
| | OUTNE = 01: LEDn = 1 (totem pole), Hi-Z (open drain).
|
| |
|
constexpr uint32_t | pca9685::reg::kOutneHiZ = 2U |
| | OUTNE = 10: LEDn = high impedance.
|
| |
|
constexpr uint8_t | pca9685::reg::kLedHReserved = 0xE0 |
| | Bits 7..5 of the _H bytes: read only, read 0.
|
| |
|
constexpr uint8_t | pca9685::reg::kLedFull = 1U << 4 |
| | Bit 4: full ON (ON_H) or full OFF (OFF_H).
|
| |
| constexpr uint8_t | pca9685::reg::kLedCountHigh = 0x0F |
| |
|
constexpr uint16_t | pca9685::reg::kMaxCount = 4095 |
| | Highest LEDn_ON and LEDn_OFF count: the 12-bit counter runs 0 to 4095 (section 7.3.3).
|
| |
|
constexpr uint8_t | pca9685::reg::kLedOffHReset = 0x10 |
| | LEDn_OFF_H after a reset: full OFF (table 7). The other three bytes reset to 0.
|
| |
|
constexpr uint8_t | pca9685::reg::kPreScaleReset = 0x1E |
| | 30: about 200 Hz from the 25 MHz oscillator.
|
| |
|
constexpr uint8_t | pca9685::reg::kPreScaleMin = 3 |
| | The hardware forces at least 3 (1526 Hz).
|
| |
Addresses, fields and reset values.