|
ISF15ACP4 Driver 0.1.0
API reference
|
Everything the driver sends at start-up, and its own time knobs. More...
#include <isf15acp4_types.hpp>
Public Attributes | |
| Variant | variant {Variant::Isf15acp4} |
| Which module; sets the geometry. | |
| Remap | remap {} |
| A0h. | |
| uint8_t | contrast_a {0x1C} |
| 81h. Reset value 0x80. | |
| uint8_t | contrast_b {0x2E} |
| 82h. | |
| uint8_t | contrast_c {0x2C} |
| 83h. | |
| uint8_t | precharge_speed_a {0x4F} |
| 8Ah: second pre-charge speed, colour A. | |
| uint8_t | precharge_speed_b {0x74} |
| 8Bh. | |
| uint8_t | precharge_speed_c {0x88} |
| 8Ch. | |
| uint8_t | master_current {0x0F} |
| 87h, 0 to 15 (1/16 to 16/16). | |
| uint8_t | start_line {0} |
| A1h, 0 to 63. | |
| uint8_t | display_offset {0} |
| A2h, 0 to 63. | |
| DisplayMode | mode {DisplayMode::Normal} |
| A4h to A7h. | |
| DimSettings | dim {} |
| ABh. | |
| bool | power_save {false} |
| B0h: false = disabled (reset value: enabled). | |
| uint8_t | phase1 {7} |
| B1h phase 1, 1 to 15 DCLK. | |
| uint8_t | phase2 {1} |
| B1h phase 2, 1 to 15 DCLK. | |
| uint8_t | clock_divide {0} |
| B3h A[3:0]: ratio is this + 1. | |
| uint8_t | clock_frequency {15} |
| B3h A[7:4]. | |
| uint8_t | precharge_level {14} |
| BBh A[5:1], 0 to 31. | |
| bool | precharge_bit0 {true} |
| BBh bit 0 (reserved): NKK Table 3 sends 1Dh, Tables 1/2 12h. | |
| bool | send_precharge_speeds {true} |
| 8Ah to 8Ch: only the ISF15ACP4 table (Table 3) has them. | |
| uint8_t | vcomh_level {16} |
| BEh A[5:1], 0 to 31. | |
| bool | linear_gray_scale {true} |
| B9h at start-up (false: the reset table stays). | |
| bool | clear_ram {true} |
| Zero GDDRAM before the supply is enabled. | |
| bool | red_on_segment_a {true} |
| Panel wiring: segment group A carries red. | |
| bool | writes_while_scrolling {false} |
| Allow RAM writes while scrolling (datasheet is silent). | |
| uint32_t | vcc_settle_ms {50} |
| VCC enable to AFh; the datasheet says only "stable". | |
| uint32_t | vcc_off_ms {reg::kVccOffTypicalMs} |
| VCC off to the end of power-down (tOFF typical). | |
| uint32_t | engine_settle_us {3000} |
| Wait after a drawing command; not in the datasheet. | |
| uint32_t | idle_dim_ms {0} |
Poll(): dim after this idle time; 0 = never. | |
| uint32_t | idle_sleep_ms {0} |
Poll(): sleep after this idle time; 0 = never. | |
| ButtonConfig | button {} |
| The switch. | |
Everything the driver sends at start-up, and its own time knobs.
Config{} is the ISF15ACP4 (NKK Table 3). The controller values are the module's table values (contrast, offset, multiplex ratio, master configuration, phase periods, clock, gray scale, pre-charge, VCOMH): NKK Note 1 says changing them may damage the OLED module. The dim contrasts may not exceed the contrasts. The time knobs are the driver's own and document an open point of the datasheets (docs/ambiguities.md). It has no operator==.