|
BNO08X Driver 0.1.0
API reference
|
The configuration of a session. Config{} is the recommended setup for a BNO085.
More...
#include <bno08x_types.hpp>
Public Member Functions | |
| constexpr bool | TimesValid () const noexcept |
| Whether every time limit is non-zero and the SPI WAKE wait ends before an operation's limit, so WAKE is always released first (DS p18). | |
| constexpr bool | Valid () const noexcept |
| Whether every field is inside its documented range. | |
Public Attributes | |
| Variant | variant {Variant::Bno085} |
| Chip of the family; selects behaviour. | |
| ReadPolicy | read_policy {ReadPolicy::HeaderThenRest} |
| How I2C and SPI reads are sized. | |
| uint8_t | i2c_address {reg::kI2cAddrLow} |
| I2C: 0x4A (SA0 low) or 0x4B (SA0 high). | |
| uint16_t | fixed_read_bytes {64} |
Bytes per read for ReadPolicy::Fixed (header included). | |
| bool | strict_variant {true} |
Refuse features the chip lacks with Variant. | |
| bool | auto_restore {true} |
| Re-send enabled features after a hub restart. | |
| bool | poll_without_int {false} |
| Guarded: read on a cadence, ignoring H_INTN (I2C only). | |
| bool | require_init_response {true} |
| Wait for the unsolicited initialise response at start. | |
| bool | frs_verify {true} |
| Read an FRS record back after writing it. | |
| bool | set_feature_confirm {false} |
Complete SetFeature on the hub's reply, not when written. | |
| bool | strict_raw {false} |
| Refuse a raw sensor whose base sensor is off. | |
| bool | strict_cont_len {true} |
| Require continuation length = remaining + 4. | |
| bool | strict_padding {false} |
| Count non-zero padding bytes. | |
| bool | tare_any_mask {false} |
| Allow tare axis masks other than 0x07 and 0x04. | |
| bool | rvc_strict {false} |
| UART-RVC: also require the index to increment by one. | |
| bool | rvc_inputs_experimental {false} |
Guarded: allow the unverified $MIB host inputs. | |
| uint16_t | startup_timeout_ms {500} |
| Limit for each start-up wait (advertisement, ready). | |
| uint16_t | op_timeout_ms {1000} |
| Limit for one operation. | |
| uint16_t | frs_write_timeout_ms {5000} |
| Limit for one FRS write step. | |
| uint32_t | wake_timeout_us {10000} |
| SPI: limit for H_INTN after WAKE. | |
| uint32_t | reset_pulse_us {1000} |
| NRST low time; the datasheet minimum is 10 ns. | |
| uint16_t | advert_retry_ms {100} |
| Without NRST: wait before asking for the advertisement. | |
| uint16_t | uart_token_timeout_ms |
| UART-SHTP: BSN validity when the hub did not advertise one. | |
| uint16_t | uart_bsq_retry_ms {20} |
| UART-SHTP: wait for a BSN before the query is sent again. | |
| uint16_t | poll_interval_ms {10} |
poll_without_int: read cadence. | |
| uint8_t | resync_limit {4} |
| Violations within the window that force a recovery. | |
| uint16_t | resync_window_ms {100} |
The window of resync_limit. | |
| uint8_t | product_id_entries {1} |
| Product ID responses accepted (1, up to 5). | |
The configuration of a session. Config{} is the recommended setup for a BNO085.
|
inlineconstexprnoexcept |
Whether every time limit is non-zero and the SPI WAKE wait ends before an operation's limit, so WAKE is always released first (DS p18).
|
inlineconstexprnoexcept |
Whether every field is inside its documented range.
Begin() would accept the configuration. | uint16_t bno08x::Config::uart_token_timeout_ms |
UART-SHTP: BSN validity when the hub did not advertise one.