Opcodes and bit masks of the chip, as constexpr values.
More...
|
|
using | StatusBp = detail::Field< uint8_t, kStatusBpShift, 2U > |
| | BP1:BP0 as a field of the status byte (Table 6-4): two bits from bit 2.
|
| |
|
| constexpr bool | IsIdleStatus (uint8_t status) noexcept |
| | True for a status byte an idle chip can return: bits 7 to 4 clear and RDY clear (Table 6-3). A busy chip returns kStatusBusyByte instead; anything else is not a status.
|
| |
|
|
constexpr uint8_t | kWren = 0x06 |
| | WREN: set the write enable latch.
|
| |
|
constexpr uint8_t | kWrdi = 0x04 |
| | WRDI: reset the write enable latch.
|
| |
|
constexpr uint8_t | kRdsr = 0x05 |
| | RDSR: read the status register.
|
| |
|
constexpr uint8_t | kWrsr = 0x01 |
| | WRSR: write the status register (BP1, BP0).
|
| |
|
constexpr uint8_t | kRead = 0x03 |
| | READ: read data from the array.
|
| |
|
constexpr uint8_t | kWrite = 0x02 |
| | WRITE: write data to the array.
|
| |
|
constexpr uint8_t | kOpcodeA8 = 0x08 |
| | Bit of a READ or WRITE opcode that carries address bit A8 (AT25040B only, Table 6-1 note 1).
|
| |
|
constexpr uint16_t | kAddressA8 = 0x100 |
| | Address bit that goes into the opcode instead of the address byte.
|
| |
|
constexpr uint16_t | kAddressLowMask = 0xFF |
| | Address bits A7 to A0: the address byte of READ and WRITE (Figures 7-6 and 7-7).
|
| |
|
constexpr uint16_t | kAddressMax = 0x1FF |
| | The highest address any part of the family decodes (A8 to A0, AT25040B).
|
| |
|
constexpr uint8_t | kStatusRdy = 0x01 |
| | RDY: 1 while a write cycle runs.
|
| |
|
constexpr uint8_t | kStatusWen = 0x02 |
| | WEN: 1 when the write enable latch is set.
|
| |
|
constexpr uint8_t | kStatusBp0 = 0x04 |
| | BP0: block protection, low bit.
|
| |
|
constexpr uint8_t | kStatusBp1 = 0x08 |
| | BP1: block protection, high bit.
|
| |
|
constexpr uint8_t | kStatusBpMask = 0x0C |
| | BP1 and BP0 together.
|
| |
|
constexpr uint8_t | kStatusBpShift = 2 |
| | Position of BP0.
|
| |
|
constexpr uint8_t | kStatusUnused = 0xF0 |
| | Bits 7 to 4: 0 when no write cycle runs.
|
| |
|
constexpr uint8_t | kStatusBusyByte = 0xFF |
| | Every bit reads 1 during a write cycle.
|
| |
Opcodes and bit masks of the chip, as constexpr values.
◆ IsIdleStatus()
| constexpr bool at25040b::reg::IsIdleStatus |
( |
uint8_t |
status | ) |
|
|
constexprnoexcept |
True for a status byte an idle chip can return: bits 7 to 4 clear and RDY clear (Table 6-3). A busy chip returns kStatusBusyByte instead; anything else is not a status.
- Parameters
-
| status | The byte RDSR returned. |
- Returns
- Whether it is an idle status.